- ESP32: NanoFlashBridge on TCP port 2323. A connection power cycles the
Nano into its bootloader and bridges TCP <-> Serial2 at 57600 baud; the
clock pauses during the session, 10 s idle timeout
- tools/nano_net_upload.py: STK500v1 uploader over TCP (standard library
only), with sync retries, write and read-back verification. avrdude 6.3
net: ports are broken on Windows, so avrdude is not used
- New nano_ota environment: pio run -e nano_ota -t upload
- README: usage, requirements, troubleshooting; TODO for hardware test
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- New native environment: pio test -e native
- test/mocks: fake Arduino core, EEPROM and recording BROSE9323 driver
- test/test_nano: 25 tests covering every command, bitmaps, bad input,
flip time storage and the periodic full redraw
- Board environments ignore tests so they are never uploaded
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- config.h: all constants and debug defines
- command_parser.h/.cpp: CommandParser class, one method per command
- settings.h/.cpp: EEPROM flip time storage
- main.cpp: setup/loop and the periodic full redraw only
- Full redraw now checks frameEnded() after the serial buffer is drained
- Drop the SPI/Adafruit_I2CDevice include workaround (not needed)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- ESP32 talks to the Nano on UART2 (GPIO 17 TX / GPIO 16 RX); Serial (USB)
is now free for debug output and boot messages no longer reach the Nano
- README: wiring table, actual schedule (clock from 08:00), TODO section
for the rewiring
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Nano / driver:
- No full on/off flip at boot; the first display() after boot is a forced
full redraw instead, since the physical dot state is unknown
- Send READY when booted
ESP32:
- relayOn() only switches and waits when the relay was off, and waits for
the Nano's READY (3 s timeout) instead of a fixed 3 s on every frame
- relayOff() ends Serial and releases the TX pin so the idle-high line no
longer back-powers the Nano through its RX pin
- No display commands are sent while the relay is off
- Switching the relay on cancels a pending power-off countdown
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- Commands run on '\n' instead of busy-waiting for a byte count, which
fixes s/F/T waiting for the next command and P drawing 0xFF garbage
- Invalid bitmaps no longer leak their data as commands; bitmap data is
streamed so full-screen bitmaps still fit
- Store flip time as uint16 with magic marker, validate 50-2000 us
- Overflow-safe millis() handling for the periodic refresh
- Run the full refresh only after D or when serial is idle, so incoming
data is not lost while the redraw blocks
- Put the boot refresh measurement behind MEASURE_REFRESH
- Fix DEBUG hex output and use F() strings to save RAM
- Driver: direct mode now updates the old buffer instead of re-setting
the new one
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- Shared BROSE9323 driver in lib/, ESPSERIAL selected via build_flags
- Nano firmware in src/nano, ESP32 firmware in src/esp32
- Move WiFi/MQTT credentials to gitignored secrets.h (template provided)
- Pin home-assistant-integration to 2.1.0 from the registry
- Add esp32_usb environment for first flash / recovery
- Add READMEs and CLAUDE.md
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
mangavalkandClaude Opus 5.5