Flipdot Display

Firmware for an 84 × 19 Brose flipdot display (three 28 × 19 panels) that runs as a Home Assistant–controlled clock.

The system uses two microcontrollers:

 ┌──────────────┐   WiFi / MQTT   ┌────────────────┐   UART 115200   ┌──────────────┐   GPIO   ┌──────────────┐
 │ Home         │ ◄─────────────► │ ESP32          │ ──────────────► │ Arduino Nano │ ───────► │ Brose        │
 │ Assistant    │                 │ (controller)   │  text commands  │ (driver)     │          │ flipdot      │
 └──────────────┘                 └───────┬────────┘                 └──────▲───────┘          │ panels 84x19 │
                                          │ GPIO 13                         │                  └──────▲───────┘
                                          ▼                                 │     power               │
                                   ┌─────────────┐                          │                         │
                                   │ Relay       │ ─────────────────────────┴─────────────────────────┘
                                   └─────────────┘

The relay powers both the panels and the Nano. When the relay is off, the Nano is off too, and it boots again each time the relay switches on. Only the ESP32 runs all the time.

Part	Folder	What it does
Arduino Nano	src/nano	Drives the panel's row and column electronics directly. Keeps a frame buffer and flips only the dots that changed. Takes simple text commands over serial.
ESP32	src/esp32	Connects to WiFi, gets the time over NTP, shows a clock with Pikachu bitmaps, exposes switches to Home Assistant over MQTT, switches display power with a relay and supports OTA updates.
BROSE9323 driver	lib/BROSE9323	Shared Adafruit_GFX display driver. On the Nano it toggles GPIO pins. On the ESP32 (-D ESPSERIAL) it turns every drawing call into a serial command for the Nano.

Because the driver is an Adafruit_GFX subclass on both boards, the ESP32 can use the normal GFX API (print, drawBitmap, fillScreen, ...). Each call is sent to the Nano and drawn there.

Repository layout

platformio.ini          one PlatformIO project, multiple environments
lib/BROSE9323/          shared flipdot driver (used by both targets)
src/nano/               Arduino Nano firmware
src/esp32/              ESP32 firmware
  secrets.example.h     template for WiFi / MQTT credentials
archive/                old, unused sketches kept for reference
CLAUDE.md               project notes for Claude Code

Building and flashing

Install PlatformIO (the VS Code extension is easiest) and open this folder.

1. Copy src/esp32/secrets.example.h to src/esp32/secrets.h and fill in your WiFi and MQTT details. secrets.h is gitignored.
2. Check the COM ports and the OTA IP in platformio.ini.
3. Build or upload:

Environment	Board	Upload method
nano	Arduino Nano (ATmega328P)	USB (COM10)
esp32	ESP32 DevKit v1	OTA over WiFi (10.1.1.198)
esp32_usb	ESP32 DevKit v1	USB (COM11). Use it for the first flash or for recovery.

pio run                          # build nano + esp32
pio run -e nano -t upload        # flash the Nano
pio run -e esp32 -t upload       # flash the ESP32 over the air
pio run -e esp32_usb -t upload   # flash the ESP32 over USB
pio device monitor -e nano       # serial monitor

In VS Code you can also pick the environment in the PlatformIO status bar.

Tip: The Nano and the ESP32 share a serial line. Disconnect the ESP32 TX → Nano RX wire before you flash the Nano over USB, or the upload may fail.

How it works

1. ESP32 boot. The ESP32 connects to WiFi and starts ArduinoOTA. After a crash or unexpected reset it stays in an OTA panic window for 15 seconds, so you can flash a fix before the main code runs again. It then switches the display relay on, starts NTP and connects to MQTT.
2. Clock loop (every second).
   • 07:00–22:00: Pikachu with a thought bubble showing HH:MM. A yawning Pikachu is shown from 17:00.
   • 22:00–23:30: the clock is only drawn on the quarter hour. In between, the relay turns the display off.
   • Night: the screen is cleared and power is cut after 30 seconds.
3. Home Assistant switches (MQTT discovery):
   • FlipDot Display Clock: off shows a Nintendo logo instead of the clock.
   • FlipDot Display Power: off clears the display and cuts power through the relay.
4. Nano. The Nano reads commands from the serial line and updates its frame buffer. On D it flips only the dots that changed. Every 2 minutes it redraws the whole screen to fix dots that did not flip.

The serial protocol is described in src/nano/README.md.