Flipdot Display

Firmware for an 84 × 19 Brose flipdot display (three 28 × 19 panels) that runs as a Home Assistant–controlled clock.

The system uses two microcontrollers:

 ┌──────────────┐   WiFi / MQTT   ┌────────────────┐   UART 115200   ┌──────────────┐   GPIO   ┌──────────────┐
 │ Home         │ ◄─────────────► │ ESP32          │ ──────────────► │ Arduino Nano │ ───────► │ Brose        │
 │ Assistant    │                 │ (controller)   │  text commands  │ (driver)     │          │ flipdot      │
 └──────────────┘                 └───────┬────────┘                 └──────▲───────┘          │ panels 84x19 │
                                          │ GPIO 13                         │                  └──────▲───────┘
                                          ▼                                 │     power               │
                                   ┌─────────────┐                          │                         │
                                   │ Relay       │ ─────────────────────────┴─────────────────────────┘
                                   └─────────────┘

The relay powers both the panels and the Nano. When the relay is off, the Nano is off too, and it boots again each time the relay switches on. Only the ESP32 runs all the time.

Part	Folder	What it does
Arduino Nano	src/nano	Drives the panel's row and column electronics directly. Keeps a frame buffer and flips only the dots that changed. Takes simple text commands over serial.
ESP32	src/esp32	Connects to WiFi, gets the time over NTP, shows a clock with Pikachu bitmaps, exposes switches to Home Assistant over MQTT, switches display power with a relay and supports OTA updates.
BROSE9323 driver	lib/BROSE9323	Shared Adafruit_GFX display driver. On the Nano it toggles GPIO pins. On the ESP32 (-D ESPSERIAL) it turns every drawing call into a serial command for the Nano.

Because the driver is an Adafruit_GFX subclass on both boards, the ESP32 can use the normal GFX API (print, drawBitmap, fillScreen, ...). Each call is sent to the Nano and drawn there.

Repository layout

platformio.ini          one PlatformIO project, multiple environments
lib/BROSE9323/          shared flipdot driver (used by both targets)
src/nano/               Arduino Nano firmware
src/esp32/              ESP32 firmware
  secrets.example.h     template for WiFi / MQTT credentials
test/test_nano/         unit tests for the Nano firmware (run on the PC)
test/test_esp32/        unit tests for the ESP32 logic (run on the PC)
test/mocks/             fake Arduino, EEPROM and display driver for the Nano tests
tools/nano_net_upload.py  uploader for flashing the Nano over WiFi
archive/                old, unused sketches kept for reference
CLAUDE.md               project notes for Claude Code

Building and flashing

Install PlatformIO (the VS Code extension is easiest) and open this folder.

1. Copy src/esp32/secrets.example.h to src/esp32/secrets.h and fill in your WiFi and MQTT details. secrets.h is gitignored.
2. Check the COM ports and the OTA IP in platformio.ini.
3. Build or upload:

Environment	Board	Upload method
nano	Arduino Nano (ATmega328P)	USB (COM10)
nano_ota	Arduino Nano (ATmega328P)	Over WiFi through the ESP32 (10.1.1.198). See Flashing the Nano over WiFi.
esp32	ESP32 DevKit v1	OTA over WiFi (10.1.1.198)
esp32_usb	ESP32 DevKit v1	USB (COM11). Use it for the first flash or for recovery.

pio run                          # build nano + esp32
pio run -e nano -t upload        # flash the Nano over USB
pio run -e nano_ota -t upload    # flash the Nano over WiFi, through the ESP32
pio run -e esp32 -t upload       # flash the ESP32 over the air
pio run -e esp32_usb -t upload   # flash the ESP32 over USB
pio device monitor -e nano       # serial monitor
pio test -e test_nano -e test_esp32   # run the unit tests on the PC

The unit tests need gcc/g++ on your PATH. On Windows you can get it from MSYS2 or Strawberry Perl.

In VS Code you can also pick the environment in the PlatformIO status bar.

Tip: The ESP32 → Nano wire goes to the Nano's RX pin, which the Nano's USB chip also uses. Disconnect that wire before you flash the Nano over USB, or the upload may fail. Flashing over WiFi (nano_ota) doesn't have this problem.

Flashing the Nano over WiFi

The ESP32 can flash the Nano for you, so you don't need a USB cable at the display:

pio run -e nano_ota -t upload

What happens:

1. The uploader (tools/nano_net_upload.py) connects to the ESP32 on TCP port 2323 and tells it the bootloader's baud rate.
2. The ESP32 pauses the clock and switches the relay off for 1 second, then on again. If the reset wire is fitted, it also pulses the Nano's RESET pin. This restarts the Nano, and its bootloader starts.
3. The ESP32 switches its link to the bootloader's baud rate and passes bytes between WiFi and the Nano.
4. The uploader writes the new firmware and reads it back to verify it.
5. When the uploader disconnects, the ESP32 switches the relay off. The clock powers the Nano on again with the new firmware and continues.

The display goes dark for the duration of the upload, which takes a few seconds.

Requirements

• The reply wire must be connected: Nano D1 (TX) → voltage divider → ESP32 GPIO 16. The uploader needs the bootloader's answers.
• The ESP32 must be running firmware with the flash bridge (this version or newer).

Bootloaders

Flashing the Nano's firmware never changes its bootloader. Both common Nano bootloaders are supported:

Bootloader	Baud	Starts after a power cycle	Reset wire
Old bootloader (ATmegaBOOT), the one this Nano has now	57600	Yes	Not needed
Optiboot ("new bootloader")	115200	No, only after a reset-pin reset	Required

By default (--baud=auto in upload_flags) the uploader tries 57600 first and then 115200. Set --baud=57600 or --baud=115200 to skip the other attempt.

If you ever replace the bootloader with Optiboot:

• Fit the reset wire: ESP32 GPIO → 1 kΩ → base of an NPN transistor (e.g. 2N2222 or BC547). Connect the collector to Nano RESET and the emitter to GND. Set NANO_RESET_PIN in src/esp32/config.h to that GPIO, for example 4. The transistor keeps the Nano's 5 V reset line away from the 3.3 V ESP32 pin.
• For uploads over USB, change board in the nano environment to nanoatmega328new.

Settings

• ESP32 IP address: upload_port in the nano_ota environment in platformio.ini. You can add a port number: 10.1.1.198:2323. For a one-time different address, use pio run -e nano_ota -t upload --upload-port 10.1.1.50.
• Port, reset pin and timings: NANO_FLASH_PORT, NANO_RESET_PIN, NANO_POWER_OFF_TIME and NANO_RESET_DELAY in src/esp32/config.h.

If it fails

Message	Cause
can't connect to ...	Wrong IP address, or the ESP32 is offline
the ESP32 flash bridge didn't accept the request	The ESP32 runs older firmware without the flash bridge. Flash it first (esp32 or esp32_usb).
no answer from the Nano bootloader	Reply wire missing, or the Nano has Optiboot and the reset wire is missing
bad reply to command ... / verify failed	Connection problem. Try again. A failed upload can leave the Nano without working firmware, but the bootloader itself is never overwritten, so flashing again (over WiFi or USB) always fixes it.

The ESP32 ends the session after 10 seconds without data, so the clock always resumes, even if the uploader is interrupted.

Security: anyone on your network can connect to port 2323 and flash the Nano, just like the ESP32's own OTA has no password. Keep the display on a trusted network.

Wiring between ESP32 and Nano

The ESP32 talks to the Nano on UART2 (Serial2, 115200 baud). The ESP32's own Serial (UART0, USB) is free for debug output.

ESP32	Nano	Notes
GPIO 17 (TX2)	D0 (RX)	Display commands
GPIO 16 (RX2)	D1 (TX)	READY and ERR replies, and bootloader answers when flashing over WiFi. Use a 5 V → 3.3 V voltage divider (e.g. 1 kΩ / 2 kΩ), because the ESP32 is not 5 V tolerant. Without it, the ESP waits a fixed 3 s after power-on, and nano_ota doesn't work.
GPIO set in NANO_RESET_PIN	RESET (through an NPN transistor)	Optional, only needed to flash a Nano with Optiboot over WiFi. See Bootloaders.
GND	GND	Common ground
GPIO 13	Relay input	Relay powers the panels and the Nano (LOW = on)

How it works

1. ESP32 boot. The ESP32 connects to WiFi and starts ArduinoOTA. After a crash or unexpected reset it stays in an OTA panic window for 15 seconds, so you can flash a fix before the main code runs again. It then switches the display relay on, waits for the Nano's READY message (at most 3 s), shows "Connecting...", starts NTP and connects to MQTT.
2. Clock. Once the time is synced, the ESP32 sends a new frame whenever the screen changes, mostly once a minute:
   • 08:00–22:00: Pikachu with a thought bubble showing HH:MM. A yawning Pikachu is shown from 17:00.
   • 22:00–23:30: the clock is only shown during the minutes :00, :15, :30 and :45. 30 seconds after each of those minutes, the relay turns the display off.
   • 23:31–08:00: the screen is cleared and power is cut after 30 seconds.
3. Home Assistant switches (MQTT discovery):
   • FlipDot Display Clock: off shows a Nintendo logo instead of the clock.
   • FlipDot Display Power: off clears the display and cuts power through the relay.
4. Nano. The Nano reads commands from the serial line and updates its frame buffer. On D it flips only the dots that changed. Every 2 minutes it redraws the whole screen to fix dots that did not flip.

The serial protocol is described in src/nano/README.md.

TODO

• Rewire the Nano link to UART2. The firmware now uses Serial2 (GPIO 16/17) instead of Serial (GPIO 1/3). Move the ESP32 TX wire from GPIO 1 to GPIO 17 before you flash this firmware, or the display gets no data. See Wiring between ESP32 and Nano.
• Add the reply wire: Nano D1 (TX) → voltage divider → ESP32 GPIO 16 (RX2). With it, the ESP sends the first frame as soon as the Nano is ready, instead of after 3 s, and the Nano can be flashed over WiFi (nano_ota).
• Test flashing over WiFi on the real hardware. The uploader is tested against a simulated bootloader, not yet against the real Nano. Check especially that the old bootloader starts after the relay power cycle.
• Check the boot timing. Build the Nano with MEASURE_REFRESH to see how long a full redraw takes. If the reply wire isn't fitted, check that 3 s (NANO_BOOT_TIMEOUT) is enough for the Nano to boot.