sync with real config parameters from sources

LCDd.conf

@@ -148,7 +148,7 @@ Brightness=255
 # This value is used when the display is normally
 # switched off in case LCDd is inactive
 OffBrightness=0
-# Set the communication speed [default: 9600; legal: 1200, 2400, 9600 or 19200]
+# Set the communication speed [default: 9600; legal: 1200, 2400, 9600, 19200i or 115200]
 Speed=9600
 # Set the firmware version (New means >= 2.0) [default: no; legal: yes, no]
 NewFirmware=no
@@ -165,7 +165,7 @@ Reboot=no
 Device=/dev/ttyS0
 # Select the LCD type (size) [default: 16x2]
 Size=16x2
-# Set the initial contrast [default: 140; legal: 0 - 1000]
+# Set the initial contrast [default: 560; legal: 0 - 1000]
 Contrast=140
 # Set the initial brightness [default: 1000; legal: 0 - 1000]
 Brightness=1000
@@ -193,7 +193,7 @@ Model=635
 Device=/dev/ttyUSB0
 # Select the LCD size [default: depending on model: 635: 20x4, 631 & 633: 16x2]
 Size=20x4
-# Set the initial contrast [default: 140; legal: 0 - 1000]
+# Set the initial contrast [default: 560; legal: 0 - 1000]
 Contrast=350
 # Set the initial brightness [default: 1000; legal: 0 - 1000]
 Brightness=1000
@@ -217,19 +217,19 @@ Reboot=yes
 
 # color settings
 # foreground color [default: blue]
-foreground=blue
+Foreground=blue
 # background color [default: cyan]
-background=cyan
+Background=cyan
 # backlight color [default: red]
-backlight=red
+Backlight=red
 
 # display size [default: 20x4]
-size=20x4
+Size=20x4
 
 # What position (X,Y) to start the left top corner at...
 # Default: (7,7)
-topleftx=7
+TopLeftx=7
-toplefty=7
+TopLefty=7
 
 
 
@@ -255,10 +255,10 @@ Reboot=no
 Keypad=yes
 
 # If you have a non standard keypad you can associate any keystrings to keys.
-# There are 6 input key in the CwLnx hardware that generate caracter
+# There are 6 input key in the CwLnx hardware that generate characters
 # from 'A' to 'F'.
 #
-# The following it the build in default mapping hardcoded in the driver.
+# The following it the built-in default mapping hardcoded in the driver.
 # You can leave those unchanged if you have a standard keypad.
 # You can change it if you want to report other keystrings or have a non
 # standard keypad.
@@ -275,6 +275,55 @@ Keypad=yes
 
 
 
+## glcdlib meta driver for graphical LCDs ##
+[glcdlib]
+
+## mandatory:
+
+# which graphical display supported by graphlcd-base to use [default: image]
+# (see /etc/graphlcd.conf for possible drivers)
+Driver=noritake800
+
+# no=use graphlcd bitmap fonts (they have only one size / font file)
+# yes=use fonts supported by FreeType2 (needs Freetype2 support in libglcdprocdriver and its dependants)
+UseFT2=yes
+
+# text resolution in fixed width characters [default: 16x4]
+# (if it won't fit according to available physical pixel resolutioni
+# and the minimum available font face size in pixels, then 
+# 'DebugBorder' will automatically be turned on)
+TextResolution=20x4
+
+# path to font file to use
+FontFile=/usr/share/fonts/corefonts/courbd.ttf
+
+
+## these only apply if UseFT2=yes:
+
+# character encoding to use
+CharEncoding=iso8859-2
+
+# minumum size in pixels in which fonts should be rendered
+MinFontFaceSize=7x12
+
+
+## optional:
+Brightness=50			# Brightness (in %) if applicable
+Contrast=50			# Contrast (in %) if applicable
+Backlight=no			# Backlight if applicable
+UpsideDown=no			# flip image upside down
+Invert=no			# invert light/dark pixels
+ShowDebugFrame=no		# turns on/off 1 pixel thick debugging
+				# border whithin the usable text area,
+				# for setting up TextResolution and
+				# MinFontFaceSize (if using FT2);
+ShowBigBorder=no		# border around the unused area
+ShowThinBorder=yes		# border around the unused area
+PixelShiftX=0
+PixelShiftY=2
+
+
+
 ## Matrix Orbital GLK driver ##
 [glk]
 
@@ -310,7 +359,7 @@ Backlight=no
 
 # If you have the additional output port ("bargraph") and you want to
 # be able to control it with the lcdproc OUTPUT command
-Outputport=no
+OutputPort=no
 
 # Specifies if the last line is pixel addressable or it controls an
 # underline effect. [default: true (= pixel addressable); legal: yes, no]
@@ -374,6 +423,17 @@ Size=20x4
 
 
 
+## Soundgraph/Ahanix/Silverstone/Uneed/Accent iMON driver ##
+[imon]
+
+# select the device to use
+Device=/dev/lcd0
+
+# display dimensions
+Size=16x2
+
+
+
 ## IrMan driver ##
 [IrMan]
 #if in trouble with IrMan, try Lirc emulator for IrMan
@@ -409,7 +469,7 @@ Device=/dev/lcd
 # Set the initial brightness [default: 255; legal: 0 - 255]
 Brightness=255
 
-# Set the communication speed [default: 19200; legal: 2400, 9600]
+# Set the communication speed [default: 9600; legal: 2400, 9600]
 Speed=9600
 
 # Reinitialize the LCD's BIOS [default: no; legal: yes, no]
@@ -444,7 +504,7 @@ MainMenuKey=RightKey
 ## HNE LCTerm driver ##
 [lcterm]
 Device=/dev/ttyS1
-size=16x2
+Size=16x2
 
 
 
@@ -488,26 +548,26 @@ Reboot=no
 [MtxOrb]
 
 # Select the output device to use [default: /dev/lcd]
-device=/dev/ttyS0
+Device=/dev/ttyS0
 
 # Set the display size [default: 20x4]
-size=20x4
+Size=20x4
 
 # Switch on the backlight? [default: yes]
 # NOTE: The driver will ignore this if the display is a vfd or vkd
 #       as they crash if the backlight is turned off
-enablebacklight=yes
+Backlight=yes
 
-# Set the initial contrast [default: 140]
+# Set the initial contrast [default: 480]
 # NOTE: The driver will ignore this if the display
 #       is a vfd or vkd as they don't have this feature
-contrast=800
+Contrast=800
 
 # Set the communication speed [default: 19200; legal: 1200, 2400, 9600, 19200]
-speed=19200
+Speed=19200
 
 # Set the display type [default: lcd; legal: lcd, lkd, vfd, vkd]
-type=lkd
+Type=lkd
 
 # The following table translate from MtxOrb Key to Logical Key.
 # See [input] section for an explanation of the key mappings
@@ -530,21 +590,27 @@ keypad_test_mode=no
 
 ## Noritake VFD driver ##
 [NoritakeVFD]
-# Port where the VFD is. Usual values are /dev/ttyS0 and /dev/ttyS1
+# device where the VFD is. Usual values are /dev/ttyS0 and /dev/ttyS1 [default: /dev/lcd]
 Device=/dev/ttyS0
 
 # Specifies the size of the LCD.
 Size=20x4
 
-Contrast=255
+# set the brightness
-# set the serial port speed [default: 9600]
+Brightness=255
+
+# set the serial port speed [default: 9600, legal: 1200, 2400, 9600, 19200, 115200]
 Speed=9600
 
+# re-initialize VFD ?
+#Reboot=yes
+
 
 
 ## Pyramid pylcd driver ##
 [pylcd]
 
+# device to connect to [default: /dev/lcd]
 Device=/dev/ttyUSB0
 
 
@@ -572,30 +638,30 @@ Port=0x378
 ## Serial VFD driver ##
 ## Drives various (see below) serial 5x7dot VFD's.  ##
 [serialVFD]
-# Port where the VFD is. Usual values are /dev/ttyS0 and /dev/ttyS1
+# device where the VFD is. Usual values are /dev/ttyS0 and /dev/ttyS1
 Device=/dev/ttyS1
 
 # Specifies the size of the VFD.
 Size=20x2
 
-# Specifies the displaytype.[default: 0]
+# Specifies the display type [default: 0]
 # 0 NEC (FIPC8367 based) VFDs.
 # 1 KD Rev 2.1.
 # 2 Noritake VFDs (*).
 # 3 Futaba VFDs (*).
 # (* most should work, not testet yet.)
-Displaytype=1
+Type=1
 
 # Display brightness [default: 255].
 # 0 min ... 255 max ... 1000 also max
 # (4 steps 0-64, 65-128, 129-192, 193-1000)
 Brightness=255
 
-# set the serial port speed [default: 9600]
+# set the serial port speed [default: 9600; legal: 1200, 2400, 9600, 19200, 115200]
 Speed=9600
 
-# enable ISO 8859 1 compatibility [default: 1]
+# enable ISO 8859 1 compatibility [default: yes; legal: yes, no]
-#ISO_8859_1=1
+ISO_8859_1=yes
 
 
 
@@ -633,7 +699,7 @@ OffBrightness=500
 ## Text driver ##
 [text]
 # Set the display size [default: 20x4]
-size=20x4
+Size=20x4
 
 
 
@@ -649,7 +715,7 @@ Port=0x378
 # Is ECP mode on? [default: yes; legal: yes, no]
 #ECPlpt=yes
 
-# Use graphic? [default: no; legal: yes, no]
+# Use graphics? [default: no; legal: yes, no]
 #graphic=no
 
 
@@ -661,10 +727,33 @@ Port=0x378
 Device=/dev/lcd
 
 # Set the communication speed [default: 9600; legal: 4800, 9600]
-Speed=19200
+Speed=9600
 
 # set display size [default: 16x2]
-Size=160x2
+Size=16x2
+
+
+
+## ELV ula200 driver ##
+[ula200]
+
+# Select the LCD size [default: 20x4]
+Size=20x4
+
+# If you have a non standard keypad you can associate any keystrings to keys.
+# There are 6 input key in the CwLnx hardware that generate characters
+# from 'A' to 'F'.
+#
+# The following it the built-in default mapping hardcoded in the driver.
+# You can leave those unchanged if you have a standard keypad.
+# You can change it if you want to report other keystrings or have a non
+# standard keypad.
+# KeyMap_A=Up
+# KeyMap_B=Down
+# KeyMap_C=Left
+# KeyMap_D=Right
+# KeyMap_E=Enter
+# KeyMap_F=Escape
 
 
 
@@ -679,63 +768,6 @@ Speed=19200
 
 
 
-## glcdlib meta driver for graphical LCDs ##
-[glcdlib]
-
-## mandatory:
-
-# which graphical display supported by graphlcd-base to use
-# (see /etc/graphlcd.conf for possible drivers)
-Driver=noritake800
-
-# no=use graphlcd bitmap fonts (they have only one size / font file)
-# yes=use fonts supported by FreeType2 (needs Freetype2 support in libglcdprocdriver and its dependants)
-UseFT2=yes
-
-# text resolution in fixed width characters (if it won't fit according
-# to available physical pixel resolution and the minimum available font
-# face size in pixels, 'DebugBorder' will automatically be turned on)
-TextResolution=20x4
-
-# path to font file to use
-FontFile=/usr/share/fonts/corefonts/courbd.ttf # path to font file to use
-#FontFile=/fonts/f8b.fnt # path to font file to use
-
-
-## these only apply if UseFT2=yes:
-
-# character encoding to use
-CharEncoding=iso8859-2
-
-# minumum size in pixels in which fonts should be rendered
-MinFontFaceSize=7x12
-
-
-## optional:
-Brightness=50			# Brightness (in %) if applicable
-Contrast=50			# Contrast (in %) if applicable
-Backlight=no			# Backlight if applicable
-UpsideDown=no			# flip image upside down
-Invert=no			# invert light/dark pixels
-ShowDebugFrame=no		# turns on/off 1 pixel thick debugging
-				# border whithin the usable text area,
-				# for setting up TextResolution and
-				# MinFontFaceSize (if unsing FT2);
-ShowBigBorder=no		# border around the unused area
-ShowThinBorder=yes		# border around the unused area
-PixelShiftX=0
-PixelshiftY=2
-
-
-
-## Soundgraph/Ahanix/Silverstone/Uneed/Accent iMON driver ##
-[imon]
-
-Size=16x2
-Device=/dev/lcd0
-
-
-
 ## OnScreen Display using libxosd ##
 [xosd]