Modified the INSTALL file a bit -- we're using automake/autoconf now, not
"edit Makefile, make, make install" ... :)
This commit is contained in:
William Ferrell
@@ -1,11 +1,11 @@
|
||||
0. REALLY-QUICK START
|
||||
|
||||
Try this, if you're in a hurry:
|
||||
edit Makefile.config (use your preferred text editor, of course)
|
||||
make
|
||||
su
|
||||
make install
|
||||
If you're in a desperate hurry:
|
||||
|
||||
./configure
|
||||
make
|
||||
su
|
||||
make install
|
||||
|
||||
1. GETTING STARTED
|
||||
|
||||
@@ -13,68 +13,15 @@ First read the README if you haven't already.
|
||||
|
||||
2. CONNECTING THE DISPLAY TO YOUR SYSTEM
|
||||
|
||||
WARNING! Danger, Will Robinson, Danger! This is pretty easy, but if
|
||||
by chance you screw up your machine by crossing some wires or by
|
||||
pouring water on things with the power turned on, don't blame us!
|
||||
Neither we, Matrix Orbital Corporation, or any manufacturer of LCDs
|
||||
you're trying to use shall be held responsible for damage incurred
|
||||
by following these directions.
|
||||
|
||||
These instructions are SPECIFICALLY FOR MATRIX ORBITAL'S DISPLAYS!
|
||||
Other displays will quite obviously have different requirements!
|
||||
|
||||
2.1. POWER CONNECTION
|
||||
|
||||
Matrix Orbital has instructions online for connecting the power
|
||||
cable. It's at http://www.matrix-orbital.com/addendum.htm
|
||||
Go there, if you're online. Or you can just read this:
|
||||
|
||||
The LCD takes either +5V or +12V, depending on which model you
|
||||
bought. You should have the +5V model unless you requested
|
||||
otherwise. Either amount can be provided conveniently by a slightly
|
||||
modified floppy power cable.
|
||||
|
||||
************* For +5V, use the RED wire. **************
|
||||
*********** For +12V, use the YELLOW wire. ************
|
||||
|
||||
Basically, disconnect the wire you don't need (yellow for +12V, or red
|
||||
for +5V) and one of the black wires (they're both grounds so it
|
||||
shouldn't matter which one you use). Then move the two remaining
|
||||
wires to the opposite ends of the connector. The power wire goes to the
|
||||
clearly marked +5V pin, and the black one goes to the also clearly
|
||||
marked GND pin.
|
||||
|
||||
Assuming you modified the cable right (we'll have pictures on the
|
||||
web site in a few days to show how this connection should be made),
|
||||
plug the other end of your modified wire into your system's power
|
||||
cables and turn the system on (you don't need to connect the serial
|
||||
cable until you know you got the power working). The LCD should light
|
||||
up and tell you what version of the BIOS it has in it. If it does,
|
||||
you've got it. If it doesn't, uh-oh. Turn the machine off quickly and
|
||||
try it again.
|
||||
|
||||
2.2. SERIAL CONNECTION
|
||||
|
||||
The LCD uses a standard DB9 serial connector. However you want to
|
||||
get from your motherboard or add-in card's serial port to the back of
|
||||
the LCD is up to you. In one of my machines, I just literally pulled
|
||||
one of the DB9 connectors off the back of my machine and plugged it
|
||||
straight into the LCD, so it was just running from the motherboard
|
||||
right to the LCD. YMMV (your milage may vary). In my new machine, I
|
||||
needed a longer cable, so I just went out and bought a 6' external
|
||||
serial cable, rolled it up and put it on top of my power supply, and
|
||||
everything worked.
|
||||
|
||||
By default (at least mine was shipped this way ;) the LCD is
|
||||
configured to run at 19,200 baud, 8-N-1. You might want to make sure
|
||||
yours is set like this; otherwise you'll need to hack our code which
|
||||
you shouldn't have to do for this to work right.
|
||||
For now, please refer to LCDproc's hardware page at
|
||||
http://lcdproc.omnipotent.net/hardware.php3 for details. Several
|
||||
different types of displays are now supported.
|
||||
|
||||
3. BUILDING LCDPROC
|
||||
|
||||
As long as you have a working gcc and make, this should work.
|
||||
|
||||
- Edit Makefile.config to configure some options.
|
||||
- Run the configure script from the distribution: ./configure
|
||||
- Run "make"
|
||||
|
||||
LCDproc will build in (hopefully) a few seconds. It's not very big. If
|
||||
@@ -89,6 +36,8 @@ to allow all users to write to the port (so users can run LCDproc).
|
||||
If you _don't_ want to allow this, change the permissions back after
|
||||
installing LCDproc. :)
|
||||
|
||||
[change this crap]
|
||||
|
||||
4. RUNNING LCDPROC / MANUAL INSTALL
|
||||
|
||||
First, you'll need to run the LCDd server. If you're in the LCDproc
|
||||
@@ -119,6 +68,7 @@ To install manually, you'll want to do something like the following:
|
||||
Some prereleases or development releases will have broken auto-install
|
||||
scripts, so manual installs may be necessary for those versions.
|
||||
|
||||
[this needs to be updated as well]
|
||||
|
||||
5. PUTTING LCDPROC IN SYSTEM STARTUP
|
||||
|
||||
@@ -156,5 +106,5 @@ That's all the OS`s we've actually done this with so far..
|
||||
Visit http://lcdproc.omnipotent.net/ for the latest updates and news
|
||||
for LCDproc. If you've got comments, suggestions, bug fixes, or
|
||||
problems (related to LCDproc, not women ;), send e-mail to either
|
||||
William W. Ferrell (choadster@earthlink.net) or Scott Scriven
|
||||
(scriven@cs.colostate.edu).
|
||||
William W. Ferrell (willfe@yahoo.com) or Scott Scriven
|
||||
(toykeeper@cheerful.com).
|
||||
|
||||
Reference in New Issue
Block a user