A CLOG DETECTED pause is usually a real blockage: on 2026-11-17 a nozzle
blocked right after a swap, the purge check passed (a blocked nozzle also
builds pressure) and the automatic resume only printed air until the next
CLOG pause. CLOG messages are still cleared after a resume, so a leftover
one cannot hide the next NOT FEEDING message.
The purge check now also fails when bd_pressure's delta is still above
pressure_max_delta (15) when the check stops: 16 good purges -3..+10, two
long purges into the blocked nozzle +19/+21 (the short ones did not show it).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Both now live in the fork https://github.com/MangaValk/bd_pressure
(klipper/, branch main, upstream PR markniu/bd_pressure#13), installed by
its klipper/install.sh and its own Moonraker update_manager entry. The fork's
bdpressure_check.py also reads the v2 firmware diagnostics. bdp_touch.py
stays here. Docs and comments point to the bd_pressure repo.
install.sh only links the files it has, so after this update it no longer
overwrites the bd_pressure links. Run ~/bd_pressure/klipper/install.sh
before updating, or the two links are left dangling.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
An AFC swap pauses and resumes the file without the PAUSE and RESUME macros
and only stops on AFC's own error state. A failed check called PAUSE, so the
swap went on and restarted the print while the printer counted as paused.
During a swap (file paused, pause_resume not paused) the check now raises an
error at the end of BLOBIFIER_CHECKED, after the temperature and sensor
cleanup. CHANGE_TOOL catches it and pauses through AFC_error. AFC's remap is
skipped, so the message names the SET_MAP command. Other failed checks still
call PAUSE.
Read from AFC 5ea84ea and Klipper 0cee841; render tests only, not yet run on
the printer.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- flex_lanes.cfg: a 5 s poller sets SET_LONG_MOVE_SPEED to 50 mm/s (AFC's
minimum) for lanes whose material is TPU/TPE/flex and back to the
configured long_moves_speed otherwise; reapplied after a restart.
- BLOBIFIER_CHECKED: remembers the temperature of the filament in the
nozzle (saved nozzle_last_temp). When it is more than flush_margin
(10C) above the new filament's, the purge runs at that temperature and
the nozzle cools back afterwards, so the leftover melts out (seen: ASA
leftover with TPU loaded at 210C).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
action_raise_error aborts while the macro renders, so an M117 in the same
macro never ran and errors such as the RESUME lane check only reached the
console. messages.cfg adds _ERROR (M117, then raise in a separate macro)
and _WARN (RESPOND TYPE=error + M117); all errors and warnings use them.
PAUSE shows AFC's error as the pause reason; RESUME, CANCEL_PRINT and
PRINT_WARMUP clear the display.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A bd_pressure that does not answer used to be reported as "pressure
skipped" and the purge passed unchecked. It now fails the check, so in
enforce mode the printer pauses (and a resume purge stays paused).
PURGE_CHECK_IGNORE_SENSOR lets purges pass without the sensor until the
print ends; _PRINT_CLEANUP clears it so the next print checks again.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
bdwidth's motion reading stays at 0, its per-reading width compensation
made the flow jump between 77 and 119%, and a USB dropout shut down
Klipper. PRINT_START no longer enables it. _PRINT_CLEANUP,
BLOBIFIER_CHECKED and PURGE_UNTIL_EMPTY only send bdwidth commands when
[bdwidth fila_width_0] exists, and bdwidth_status reports present: False
with neutral values when it is not configured, so the section can be
removed from printer.cfg.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
_RESUME_PRINT purges 40 mm with BLOBIFIER_CHECKED (instead of the 2 mm
unretract), so the nozzle is primed, wiped and checked before going back
to the print. A failed purge check raises an error that aborts the whole
resume, AFC_RESUME's restore included, so the printer stays paused; the
next RESUME checks again. RESUME PURGE=0 skips the purge.
The purge check records a failure in _PURGE_CHECK_CFG.last_failed, since
its PAUSE has no effect while the printer is already paused.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- Split the macro files into folders by topic (print, heating, afc,
pressure_advance, spoolman, leds, sensors); klipper-macros.cfg is the
one file printer.cfg includes. Macros moved unchanged; the effective
config is identical apart from the paths of the PA shell scripts.
- Add the modified Blobifier (Turtleblobifier for AFC) and define
[save_variables] once in save_variables.cfg instead of in both
blobifier.cfg and the PA macros (same file, bd_pa_variables.cfg).
- PRINT_WARMUP: heat to the loaded lane's temperature before the first
tool change. AFC skips heating when the loaded lane's tool number is
not in the print file's temperature list, and the unload then failed
below min_extrude_temp.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>