TWIST_CALIBRATE: wipe the nozzle before the contact step
Plastic left on the nozzle sets the contact Z too high and squeezes away during the run. The first real Verify (2026-11-04, about an hour after a PLA print) saw bd_pressure and Beacon contact sink by about 0.004 mm per point while proximity held within 0.006 mm, so it asked for a re-run. That cause is likely but not yet confirmed. Same order as PRINT_START: QGL, G28 Z, BLOBIFIER_CLEAN with the guard in log mode, then the contact step. Refuses to start without BLOBIFIER_CLEAN or _GUARD_ON. Tested against the simulated printer only. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
7bee9a1ecd
commit
1fc4b26366
3 files changed
+14
-5
No files matched your search
+10
-2
@@ -26,7 +26,7 @@ Modes:
|
||||
y 175/295. With good compensation, bdp - proximity is flat along X.
|
||||
|
||||
Both: BED_MESH_CLEAR (the active mesh only; saved profiles stay), nozzle 150C,
|
||||
HOME, QGL, contact Z, 2 passes (second in reverse order to cancel slow drift),
|
||||
HOME, QGL, G28 Z, nozzle wipe (BLOBIFIER_CLEAN), contact Z, 2 passes (second in reverse order to cancel slow drift),
|
||||
then Z10 and nozzle off. The bed heater is not touched.
|
||||
|
||||
Safety: refuses to start when Klipper is not ready, a print runs or another
|
||||
@@ -210,7 +210,8 @@ def preflight(p, mode):
|
||||
raise Problem("A print is running or paused. Try again afterwards.")
|
||||
objects = p.get("/printer/objects/list")["objects"]
|
||||
settings = p.query("configfile")["configfile"]["settings"]
|
||||
missing = [m for m in ("HOME", "_NOZZLE_CONTACT_TEMP", "_TWIST_STATE")
|
||||
missing = [m for m in ("HOME", "_NOZZLE_CONTACT_TEMP", "_TWIST_STATE",
|
||||
"_GUARD_ON", "BLOBIFIER_CLEAN")
|
||||
if "gcode_macro " + m not in objects]
|
||||
missing += [s for s in ["beacon"] + (["bdp_touch"] * (mode == "verify"))
|
||||
if s not in settings]
|
||||
@@ -287,6 +288,13 @@ def run_points(p, mode, path):
|
||||
p.gcode("_NOZZLE_CONTACT_TEMP WAIT=1")
|
||||
p.gcode("HOME")
|
||||
p.gcode("QUAD_GANTRY_LEVEL")
|
||||
# As in PRINT_START. Plastic left on the nozzle sets the contact Z too high
|
||||
# and squeezes away during the run: the touches then sink by ~0.004 mm per
|
||||
# point (2026-11-04). QGL moved Z, so home again before the brush takes the
|
||||
# nozzle below Z0. The bristles press on the nozzle: guard in log mode.
|
||||
p.gcode("M117 Twist %s: cleaning the nozzle" % mode)
|
||||
p.gcode("G28 Z")
|
||||
p.gcode("_GUARD_ON PHASE=brush MODE=log\nBLOBIFIER_CLEAN\n_GUARD_OFF")
|
||||
p.gcode("G28 Z METHOD=CONTACT CALIBRATE=1")
|
||||
p.gcode("G90")
|
||||
p.say("%d points, %d passes. The nozzle will touch the bed at each one."
|
||||
|
||||
Reference in new issue
Block a user