diff --git a/macros/calibration/twist_check.cfg b/macros/calibration/twist_check.cfg index 2bb564a..58eae1c 100644 --- a/macros/calibration/twist_check.cfg +++ b/macros/calibration/twist_check.cfg @@ -80,7 +80,7 @@ gcode: {% if bed > 40 %} RESPOND TYPE=command MSG="action:prompt_text Note: the bed is at {bed|int} C. The reference runs were on a cold bed, so wait for it to cool unless you want this on purpose." {% endif %} - RESPOND TYPE=command MSG="action:prompt_text It heats the nozzle to 150 C, homes, levels and takes {'25' if mode == 'measure' else '17'} minutes. The configuration is not changed." + RESPOND TYPE=command MSG="action:prompt_text It heats the nozzle to 150 C, homes, levels, wipes the nozzle on the brush and takes {'25' if mode == 'measure' else '17'} minutes. The configuration is not changed." RESPOND TYPE=command MSG="action:prompt_footer_button Back|TWIST_CALIBRATE|secondary" RESPOND TYPE=command MSG="action:prompt_footer_button All checked, start|_TWIST_START MODE={mode}|primary" RESPOND TYPE=command MSG="action:prompt_show" diff --git a/scripts/twist_check.md b/scripts/twist_check.md index b7e1832..d3ea9f3 100644 --- a/scripts/twist_check.md +++ b/scripts/twist_check.md @@ -42,8 +42,8 @@ The calibration clears the active bed mesh (saved profiles stay). ## What the run does -It heats the nozzle to 150 C, homes, runs QGL and sets Z by contact. It then -visits each point twice, the second pass in reverse order to cancel slow drift. +It heats the nozzle to 150 C, homes, runs QGL, wipes the nozzle on the Blobifier +brush and sets Z by contact. It then visits each point twice, the second pass in reverse order to cancel slow drift. The nozzle touches the bed at every point. At the end it lifts to Z10 and turns the nozzle heater off. The bed heater is not touched. @@ -140,6 +140,7 @@ that computer, under its own home directory. - Mainsail with `[respond]`, for the windows - `gcode_shell_command`, to start the script from a macro - Beacon, used in contact and proximity mode +- The Blobifier macros (`BLOBIFIER_CLEAN`) and the nozzle guard (`_GUARD_ON`) - Python 3 on the Pi (standard library only), and Moonraker trusting localhost - For Verify: `[bdp_touch]` and the bd_pressure load-check firmware - `[axis_twist_compensation]` is not needed for the first Measure; the result diff --git a/scripts/twist_check.py b/scripts/twist_check.py index ffe6edd..069715a 100644 --- a/scripts/twist_check.py +++ b/scripts/twist_check.py @@ -26,7 +26,7 @@ Modes: y 175/295. With good compensation, bdp - proximity is flat along X. Both: BED_MESH_CLEAR (the active mesh only; saved profiles stay), nozzle 150C, -HOME, QGL, contact Z, 2 passes (second in reverse order to cancel slow drift), +HOME, QGL, G28 Z, nozzle wipe (BLOBIFIER_CLEAN), contact Z, 2 passes (second in reverse order to cancel slow drift), then Z10 and nozzle off. The bed heater is not touched. Safety: refuses to start when Klipper is not ready, a print runs or another @@ -210,7 +210,8 @@ def preflight(p, mode): raise Problem("A print is running or paused. Try again afterwards.") objects = p.get("/printer/objects/list")["objects"] settings = p.query("configfile")["configfile"]["settings"] - missing = [m for m in ("HOME", "_NOZZLE_CONTACT_TEMP", "_TWIST_STATE") + missing = [m for m in ("HOME", "_NOZZLE_CONTACT_TEMP", "_TWIST_STATE", + "_GUARD_ON", "BLOBIFIER_CLEAN") if "gcode_macro " + m not in objects] missing += [s for s in ["beacon"] + (["bdp_touch"] * (mode == "verify")) if s not in settings] @@ -287,6 +288,13 @@ def run_points(p, mode, path): p.gcode("_NOZZLE_CONTACT_TEMP WAIT=1") p.gcode("HOME") p.gcode("QUAD_GANTRY_LEVEL") + # As in PRINT_START. Plastic left on the nozzle sets the contact Z too high + # and squeezes away during the run: the touches then sink by ~0.004 mm per + # point (2026-11-04). QGL moved Z, so home again before the brush takes the + # nozzle below Z0. The bristles press on the nozzle: guard in log mode. + p.gcode("M117 Twist %s: cleaning the nozzle" % mode) + p.gcode("G28 Z") + p.gcode("_GUARD_ON PHASE=brush MODE=log\nBLOBIFIER_CLEAN\n_GUARD_OFF") p.gcode("G28 Z METHOD=CONTACT CALIBRATE=1") p.gcode("G90") p.say("%d points, %d passes. The nozzle will touch the bed at each one."