116 lines
4.7 KiB
C
116 lines
4.7 KiB
C
/* Name: usbconfig.h
|
|
* Project: AVR USB driver
|
|
* Author: Christian Starkjohann, modified by Till Harbaum
|
|
* Creation Date: 2005-04-01
|
|
* Tabsize: 4
|
|
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
|
* License: Proprietary, free under certain conditions. See Documentation.
|
|
* This Revision: $Id: usbconfig.h,v 1.2 2007/01/14 12:12:27 harbaum Exp $
|
|
*/
|
|
|
|
#ifndef __usbconfig_h_included__
|
|
#define __usbconfig_h_included__
|
|
|
|
/*
|
|
General Description:
|
|
This file contains parts of the USB driver which can be configured and can or
|
|
must be adapted to your hardware.
|
|
*/
|
|
|
|
/* ---------------------------- Hardware Config ---------------------------- */
|
|
|
|
#define USB_CFG_IOPORTNAME C
|
|
/* This is the port where the USB bus is connected. When you configure it to
|
|
* "PORTB", the registers PORTB, PINB (=PORTB+2) and DDRB (=PORTB+1) will be
|
|
* used.
|
|
*/
|
|
#define USB_CFG_DMINUS_BIT 0
|
|
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
|
* This MUST be bit 0. All other values will result in a compile error!
|
|
*/
|
|
#define USB_CFG_DPLUS_BIT 1
|
|
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
|
* This may be any bit in the port. Please note that D+ must also be connected
|
|
* to interrupt pin INT0!
|
|
*/
|
|
|
|
/* --------------------------- Functional Range ---------------------------- */
|
|
|
|
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
|
/* Define this to 1 if you want to compile a version with two endpoints: The
|
|
* default control endpoint 0 and an interrupt-in endpoint 1.
|
|
*/
|
|
#define USB_CFG_INTR_POLL_INTERVAL 10
|
|
/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
|
|
* interval. The value is in milliseconds and must not be less than 10 ms for
|
|
* low speed devices.
|
|
*/
|
|
#define USB_CFG_IS_SELF_POWERED 0
|
|
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
|
* device is powered from the USB bus.
|
|
*/
|
|
#define USB_CFG_MAX_BUS_POWER 75
|
|
/* Set this variable to the maximum USB bus power consumption of your device.
|
|
* The value is in milliamperes. [It will be divided by two since USB
|
|
* communicates power requirements in units of 2 mA.]
|
|
*/
|
|
#define USB_CFG_SAMPLE_EXACT 1
|
|
/* This variable affects Sampling Jitter for USB receiving. When it is 0, the
|
|
* driver guarantees a sampling window of 1/2 bit. The USB spec requires
|
|
* that the receiver has at most 1/4 bit sampling window. The 1/2 bit window
|
|
* should still work reliably enough because we work at low speed. If you want
|
|
* to meet the spec, set this value to 1. This will unroll a loop which
|
|
* results in bigger code size.
|
|
* If you have problems with long cables, try setting this value to 1.
|
|
*/
|
|
#define USB_CFG_IMPLEMENT_FN_WRITE 0
|
|
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
|
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
|
* bytes.
|
|
*/
|
|
#define USB_CFG_IMPLEMENT_FN_READ 0
|
|
/* Set this to 1 if you need to send control replies which are generated
|
|
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
|
* data from a static buffer, set it to 0 and return the data from
|
|
* usbFunctionSetup(). This saves a couple of bytes.
|
|
*/
|
|
|
|
/* -------------------------- Device Description --------------------------- */
|
|
|
|
#define USB_CFG_VENDOR_ID 0x03, 0x04
|
|
/* USB vendor ID for the device, low byte first. */
|
|
#define USB_CFG_DEVICE_ID 0x30, 0xc6
|
|
/* This is the ID of the device, low byte first. It is interpreted in the
|
|
* scope of the vendor ID. The only requirement is that no two devices may
|
|
* share the same product and vendor IDs. Not even if the devices are never
|
|
* on the same bus together!
|
|
*/
|
|
#define USB_CFG_DEVICE_VERSION 0x09, 0x01
|
|
/* Version number of the device: Minor number first, then major number.
|
|
*/
|
|
#define USB_CFG_VENDOR_NAME 'T', 'i', 'l', 'l', ' ', 'H', 'a', 'r', 'b', 'a', 'u', 'm'
|
|
#define USB_CFG_VENDOR_NAME_LEN 12
|
|
/* These two values define the vendor name returned by the USB device. The name
|
|
* must be given as a list of characters under single quotes. The characters
|
|
* are interpreted as Unicode (UTF-16) entities.
|
|
* If you don't want a vendor name string, undefine these macros.
|
|
*/
|
|
#define USB_CFG_DEVICE_NAME 'L', 'C', 'D', '2', 'U', 'S', 'B',' ','I','n','t','e','r','f','a','c','e'
|
|
#define USB_CFG_DEVICE_NAME_LEN 17
|
|
/* Same as above for the device name. If you don't want a device name, undefine
|
|
* the macros.
|
|
*/
|
|
#define USB_CFG_DEVICE_CLASS 0xff
|
|
#define USB_CFG_DEVICE_SUBCLASS 0
|
|
/* See USB specification if you want to conform to an existing device class.
|
|
*/
|
|
#define USB_CFG_INTERFACE_CLASS 0
|
|
#define USB_CFG_INTERFACE_SUBCLASS 0
|
|
#define USB_CFG_INTERFACE_PROTOCOL 0
|
|
/* See USB specification if you want to conform to an existing device class or
|
|
* protocol.
|
|
*/
|
|
|
|
|
|
#endif /* __usbconfig_h_included__ */
|