Pages choose their own refresh effect (or the Hardware setting), used when
the page appears and for its own changes. Schedule blocks that switch
instantly and rules still switch instantly. The ESP32 sends page effects
to the Nano with a new no-save flag (E ...,2), so page switches don't wear
the Nano's EEPROM. Page format 7 (version 6 pages are converted).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The Nano's periodic full redraw blocked for ~0.8 s. A frame that arrived
meanwhile overflowed its 64-byte serial buffer; lost bytes in a bitmap
shift the rest of the image (picture moved up), and diff frames never
repaired it.
- Nano: all drawing (frames, effects, the dot refresh) runs from update()
in ~1 ms slices; the refresh pauses while a frame is received or shown
- New commands: C (reply with the image checksum) and I (refresh minutes,
EEPROM)
- ESP32: NanoMonitor asks for the checksum after frames and sends the whole
image again on a mismatch, missing answer or Nano restart; counts ERR
replies. Periodic whole-image resync.
- Settings: "Dot refresh" and "Image resync" intervals (settings v5,
v4 records are migrated)
- System tab: loop timing, free memory, frame check counts
- test_driver: the real driver against a simulated panel
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Home Assistant: remove the Clock switch (its entity is deleted on connect),
add an IP sensor and Mode / Off image dropdowns whose options follow the
saved bitmaps. Remove the built-in "Nintendo border" bitmap.
Off image: a bitmap (or blank) left on the dots when the display switches off.
Nano: pause after each flip pulse and repeat pulses for changed dots, both
stored in EEPROM (G/N commands). Refresh effects (E command): instant,
sparkle, wipe, rain, from the middle out, diagonal, spiral, flip all then
reveal, push and random, optionally only for small changes. Effects run in
steps from loop() so serial input keeps flowing.
Web UI: flip settings, refresh effect and test patterns under Settings; the
System tab shows why the ESP32 last restarted. Settings records from
versions 1 and 2 are migrated. Firmware 2.3.0.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- Web UI on port 80: live view of the display, choose the page (clock or
a bitmap), bitmaps (list, show, live, edit, delete), draw / image upload
with conversion in the browser, live mode, settings, Home Assistant
- Live view from a shadow buffer in the BROSE9323 driver (shownPixel)
- Settings in NVS with the original behaviour as defaults: schedule times,
quarter hours, yawning Pikachu, No WiFi screen, flip time, status LED,
Home Assistant broker (restart on change)
- Bitmaps on LittleFS; new 320 KB partition, ota slots now 1.31 MB
- DisplayController: pages, live mode, settings; app.cpp holds the objects
- README for the recovery app; docs for the web UI
- Tests: settings, time parsing, bitmap format and names, schedule with
settings, pages and live mode (95 total)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- Clock firmware: 'Connecting to WiFi...' and 'Getting the time...' at
boot, 'Crashed!' in the OTA-only modes, and 'No WiFi' with the time
when WiFi is down for over a minute (new DisplayController screen)
- Recovery app: shows its reason, the setup WiFi name, or its IP address,
then powers the display off (flipdots keep the image)
- StatusScreen and drawTextLines shared by both apps
- Driver: ESP begin() no longer draws 'ESP Connected'
- Tests: No WiFi screen, short reason texts (70 total)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
mangavalkandClaude Opus 5.5