Files
hexapod-robot/2026-current/sim/README.md
T
mangavalkandClaude Opus 5.5 179afdb705 2026 docs: review of every README against today's state
- README / CLAUDE.md layout: dongle/, hardware/, tools/ submodule,
  make_remote_hmi.py; telemetry in the protocol; the PC can take the
  robot's place on the radio. CLAUDE.md: NextionUI is on Serial2 (said
  Serial1); remote-without-robot via the dongle + sim.
- remote/README: MPU6050 supply row; stick calibration button names of the
  new SETUP page; upload/USB-port hints.
- remote/NEXTION.md: display on Serial2, how the Editor upload goes.
- robot/README: Battery in the file list, Comms/ServoDriver roles, packet
  structs instead of payload size, check the IMU gives live data (the
  remote's MPU6050 needed a full reset; RobotIMU::begin() only wakes it).
- sim/README: smoke test covers telemetry and servo calibration;
  OpenScadModel.
- dongle/README: AT2401C test result, app command table, SignalRGB note,
  air settings incl. ack payloads.
- PLANNING.md: the display direction is in the generated HMI.
- Unity README: what the project is.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-17 22:56:14 +01:00

6.2 KiB
Raw Blame History

Firmware simulation (software-in-the-loop)

This folder compiles the unchanged robot firmware (robot/*.cpp plus robot.ino) into a Windows DLL. The Unity project (Hexapod_Simulation_Unity/) runs that DLL, so the code you test in the simulation is exactly the code you flash to the Teensy. robot/ has no #ifdef SIM anywhere.

robot/ (unchanged) ──► PlatformIO + Teensy core ──► Teensy 3.6 firmware
                   └─► CMake + g++ + sim/shim/  ──► sim/build/hexapod_sim.dll ──► Unity

How it works

shim/ provides PC stand-ins for the only hardware the firmware touches:

Firmware uses Simulated as
analogWrite() hardware PWM (how ServoDriver drives the servos) the pulse width per pin, worked out from duty, resolution and frequency, then decoded back to angles through Config.h's per-servo SERVOS table
Wire + MPU6050 registers a register-level fake MPU6050 at 0x68, fed from the simulated body's tilt and rotation
RF24 a simulated radio: packets are received only if channel, address, data rate and payload size match (any length up to 32 once enableAckPayload() turns on dynamic payloads, as on the chip), and the RX FIFO holds 3. writeAckPayload() goes back with the next packet received: hxsim_get_ack_payload returns it (the robot's Telemetry)
millis() / micros() / Serial a simulated clock that Unity advances, and captured serial I/O

robot_ino.cpp compiles robot.ino itself and exposes read-only views of its globals (state machine, heading, IMU filter, gait phase) for status display. HexapodSimApi.h is the C API. Its forward kinematics is written separately from robot/Kinematics.cpp on purpose, so it can catch IK mistakes.

Build

Needs a 64-bit g++ and CMake. Strawberry Perl's C:\Strawberry\c\bin has g++, cmake and ninja, and the script falls back to it automatically. From the 2026-current folder in PowerShell:

.\sim\build.ps1             # configure (first time) + build + smoke test
.\sim\build.ps1 -NoTest     # build only
.\sim\build.ps1 -Clean      # rebuild from scratch

To run the steps by hand, use separate lines. Windows PowerShell 5.1 has no &&:

cmake -S sim -B sim\build -G Ninja
cmake --build sim\build
.\sim\build\sim_smoke.exe

Rebuild after any change in robot/ or shared/. In Unity, press Play (or Reload firmware in the panel) to pick up the new DLL. Unity copies the DLL before loading it, so it never locks the build output and you don't need to restart the editor.

Headless smoke test (tests/sim_smoke.cpp)

It drives the firmware the way the remote would and checks:

  • disarmed at power-on,
  • arm lands in SIT,
  • stand reaches STAND,
  • IK gives valid solutions and the feet end up at STANCE_HEIGHT,
  • FLAG_WALK leads to WALKING,
  • +vx moves the body forward,
  • link loss disarms,
  • a wrong-size packet is ignored,
  • the robot's telemetry comes back in the ack payload, and every servo calibration command (HOLD / SET / SAVE / REVERT, arming refused) works,
  • the serial harness still works,
  • plus the body-pose, leg-clearance, heading and robot-gyro checks listed in the file.

Using it in Unity

Open Hexapod_Simulation_Unity and press Play in Main.unity. No scene edits are needed: HexapodSimBootstrap adds a HexapodSimulation object, disables the old movement scripts (Walk, RotationControl, Leg), and binds the existing leg rig by name (Leg → hip1 / Hip2 / Knie). By default OpenScadModel swaps the old scene's robot for the OpenSCAD model of the real one (HexapodSimulation.useOpenScadModel). The on-screen panel (F1 toggles it) offers two input sources:

  • Keyboard: test without a remote. WASD walks, Q/E turns, IJKL + U/O drive the right stick, 1–7 flip the toggles, Backspace disarms, +/- change speed. The panel has every remote toggle, the speed slider and simulated handset tilt (remote gyro).
  • Real remote (radio): the real handheld remote, over the air. The USB nRF24 dongle (../dongle/, bridge mode) receives its packets, they go into the firmware byte for byte, and the robot's Telemetry goes back as the radio's ack payload, exactly like the real robot's Comms. The remote's display then shows the simulated robot (state, IMU, joint angles, servo calibration). DongleLink.cs finds the dongle's CH340 port by itself (or set SimRemote.donglePort, e.g. COM7); quit SignalRGB first, it grabs CH340 ports. Don't run the real robot at the same time: both would answer the remote.

There's no USB link to the remote or the robot any more (the old joystick and serial-harness inputs and the Serial* / HandleHoystick scripts are gone): everything goes over the radio.

The panel also has a ground tilt slider (to test the robot gyro), and live firmware state, joint angles, foot contact, the packet on air and the robot's debug prints.

The body moves kinematically, computed in the DLL (SimBody.cpp), so Unity shows what the smoke test checks:

  • The body rests on the support plane of its feet, the plane all feet are on or above.
  • Grounded feet don't slide.
  • The simulated MPU6050 reads that body's tilt and rotation rate.

The sphere at each foot (Point) is placed by the DLL's forward kinematics. If it doesn't sit on the tibia tip, the rig and Config.h disagree.

Setup that lives in the Inspector on HexapodSimulation:

  • forwardAxis: robot forward = Unity −X by default, taken from the old scene's invertForLeftLeg naming.
  • unitsPerMm: 0.1, since the model is in cm.
  • kneeRestDeg: −90, the rig's knee pose at rotation 0.

For a custom setup instead of the bootstrap, add a HexapodSimulation component to the scene yourself.

What is not simulated

  • Physics (mass, falling, slipping, servo torque and speed).
  • Whether the calibration matches the real servos. The sim decodes pulses through the same SERVOS table the firmware uses, so it shows what the firmware intends, including pulse-limit clamping (which is how it caught the old ±90° coxa offsets). Whether a real servo turns that way is a bench check.
  • The remote firmware, in Keyboard mode: SimRemote.cs mirrors its packet rules instead. With the real remote over the radio, its own firmware runs.