Commit Graph
6 Commits
Author SHA1 Message Date
mangavalkandClaude Opus 5.5 179afdb705 2026 docs: review of every README against today's state
- README / CLAUDE.md layout: dongle/, hardware/, tools/ submodule,
  make_remote_hmi.py; telemetry in the protocol; the PC can take the
  robot's place on the radio. CLAUDE.md: NextionUI is on Serial2 (said
  Serial1); remote-without-robot via the dongle + sim.
- remote/README: MPU6050 supply row; stick calibration button names of the
  new SETUP page; upload/USB-port hints.
- remote/NEXTION.md: display on Serial2, how the Editor upload goes.
- robot/README: Battery in the file list, Comms/ServoDriver roles, packet
  structs instead of payload size, check the IMU gives live data (the
  remote's MPU6050 needed a full reset; RobotIMU::begin() only wakes it).
- sim/README: smoke test covers telemetry and servo calibration;
  OpenScadModel.
- dongle/README: AT2401C test result, app command table, SignalRGB note,
  air settings incl. ack payloads.
- PLANNING.md: the display direction is in the generated HMI.
- Unity README: what the project is.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-17 22:56:14 +01:00
mangavalkandClaude Opus 5.5 2b4750f8f4 2026 sim: drive the Unity simulation with the real remote over the radio
Dongle (app):
- bridge mode: stands in for the robot's radio (ch 96 / 250k / HXPD1,
  auto-ack, dynamic payloads, ack payloads). Received packets go to the PC
  as A5-framed 'R' frames; the PC's 'A' frames become the ack payload of
  the next packet, like robot/Comms.cpp; dropped after ~0.5 s without a
  refresh. 'S' status once a second.
- USART RX through circular DMA into a ring buffer, overrun stall
  disabled, error flags cleared: a burst (e.g. SignalRGB probing the port)
  used to deafen the app until a replug.
- RX test mode ('x') accepts protocol v4's dynamic-length packets.
- safeboot_flash.py --knock: keeps knocking across a replug to catch
  safeboot's cold-boot window when the app doesn't answer.

Unity:
- SimRemote sources: Keyboard, or the real remote via the dongle
  (DongleLink.cs: kernel32 serial, auto-finds the CH340, all port I/O on
  one background thread). Packets go into the firmware byte for byte, the
  robot's telemetry goes back on the ack, so the remote's display shows
  the sim. Tested end to end with the real remote.
- Dropped the USB joystick and robot-serial-harness inputs and the old
  Serial/Serial2/Serial3/HandleHoystick scripts (and their components in
  Main.unity): no USB links to remote or robot any more.
- Test panel: dongle status; no sideways scroll bar.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-17 22:48:41 +01:00
mangavalkandClaude Opus 5.5 0b836af8de 2026 remote: tabbed Nextion UI, robot telemetry, servo centre calibration
Protocol v4: CmdPacket grows to 26 bytes (cal_cmd, cal_servo, cal_value);
new 30-byte Telemetry rides back on the nRF24 ack payload (robot state,
IMU, battery, 18 joint angles, packets/s, servo-cal echo). Each end drops
wrong-length packets, so version mismatches still fail closed.

Robot (owner-approved): SERVO_CAL state while disarmed, per-servo centre
trims (+-200 us) in EEPROM, telemetry, battery reading; the IMU estimate
now always runs (leveling still gated by ROBOT GYRO).

Remote: generated HMI (scripts/make_remote_hmi.py) with pages splash,
drive, status, servos, cal, setup, upload; page-aware NextionUI that only
writes the showing page and only what changed; servo calibration and
UPDATE DISPLAY on the touchscreen and serial console; battery module.
The display is on Serial2 (pins 7/8), found on the real remote; the old
sketch's Serial1 was never connected to it.

Sim: RF24 shim supports ack payloads, API version 8
(hxsim_get_ack_payload); sim_smoke checks telemetry and every CAL command.
Unity CmdPacket mirror updated.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-17 14:42:37 +01:00
mangavalk dfd4d34512 Fold LEGACY into the generation folders
The LEGACY copies of HexapodRobot, Hexapod_NEW, Hexapod_Teensy and the old remote sketch were identical to the imported repos and are removed. The old Nextion design moves to 2019-teensy-nrf24/remote-nextion/, the 2019 remote case files to 2019-teensy-nrf24/remote-case/. Paths in CLAUDE.md, READMEs, remote/ comments, sim/build.ps1, the Unity DLL message and .vscode/settings.json now point to the new places. robot/ is not touched (its CLAUDE.md asks to check with the owner first).
2026-10-25 17:30:35 +01:00
mangavalkandClaude Opus 5.5 5ff85c4eb8 Robot: Teensy 3.6 with the old robot's servo wiring and calibration
- LEGACY/Hexapod_Teensy/: old robot sketch (reference only).
- platformio.ini: robot env targets teensy36 (owner-confirmed board).
- Config.h: per-servo SERVOS table (pin, pulse at 0 deg, signed
  us/deg, pulse limits) built from the old sketch's pins, ranges, trims
  and the old Unity servo directions. Rear-left/front-left coxa offsets
  set to 0: the owner re-horns those two servos (the old +-90 left them
  at the end of travel; the sim showed them clamping).
- ServoDriver: 18 servos on hardware PWM (50 Hz, 16-bit); the Teensy 3.6
  Servo library stops at 12.
- Radio on CE 39 / CSN 15 with SPI SCK on pin 14.
- sim: analogWrite/PWM shims, pulses decoded through SERVOS (API v6).
- Docs: CLAUDE.md, READMEs.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-01 15:53:55 +02:00
mangavalkandClaude Opus 5.5 935526eab5 Firmware simulation, Unity project, and sim-verified robot fixes
Simulation
- sim/: the unchanged robot firmware compiled into hexapod_sim.dll
  against PC stand-ins (Arduino, Servo, Wire + register-level MPU6050,
  RF24 with matching-config radio), a kinematic body model (support
  plane + planted-foot odometry) that also drives the simulated IMU,
  and a headless smoke test (sim_smoke). build.ps1 builds and tests.
- Hexapod_Simulation_Unity/ folded in (history kept in a bundle
  outside the repo). Assets/HexapodSim loads the DLL, drives the
  existing leg rig, and offers joystick / keyboard / robot-serial
  input plus a test panel.

Robot (all found or confirmed in the simulation)
- Config.h geometry taken from the Unity model.
- IK femur elevation sign, gait stance direction, body pose
  rotation direction, yaw lever arm.
- Stance feet integrated from the current command; gait restarts at
  mid-stance; heading integrates the applied turn rate, only while
  walking.
- Leg clearance and reach checks (Limits::feetFeasible); walk command
  and body pose scaled as a whole, pose scale rate-limited, planted
  feet guarded so the body never snaps or legs collide.
- Robot-gyro self-leveling as an integrator.
- Heading mode: steering relative to the body; S walks backward.
- Standing height from the remote (STANCE_HEIGHT_RANGE_MM).

Protocol v3 (reflash both boards)
- CmdPacket gains body_height (22 bytes).

Remote
- Height slider (Nextion hHeight/nHeight, serial [ ]).
- Fixed unspecified I2C read order in RemoteIMU.

LEGACY/: owner's old Nextion HMI and remote hardware assets.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-09-29 00:37:12 +02:00