- README: the HMI is generated turned round (nothing to set in the Editor); PC radio link: bridge mode done, no USB links any more, what's left (Unity driving the real robot, three nodes at once). - remote/README checklist: sticks and IMU checked, display uploaded, radio checked against the sim through the dongle; replace the IMU board. - CLAUDE.md: display runs the new HMI; next steps. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
117 lines
6.1 KiB
Markdown
117 lines
6.1 KiB
Markdown
# Hexapod
|
|
|
|
A six-legged walking robot (Teensy 3.6) and its handheld remote
|
|
(Teensy 4.0 + Nextion touchscreen), linked over nRF24L01.
|
|
|
|

|
|

|
|
|
|
The remote above is the new design (`hardware/openscad/remote_v2.scad`, not
|
|
printed yet). The original printed remote is on the
|
|
[archive page](hardware/openscad/ARCHIVE.md).
|
|
|
|
```
|
|
robot/ robot firmware: IK, gait, body pose, IMU stabilization, state machine
|
|
remote/ remote firmware: 2 x 3-axis sticks, MPU6050 tilt, Nextion UI, RF24 TX
|
|
shared/ HexapodProtocol: the CmdPacket wire format + radio settings used by both
|
|
sim/ the unchanged robot firmware compiled into a DLL for the simulation
|
|
Hexapod_Simulation_Unity/ Unity project that runs that DLL on the 3D model
|
|
dongle/ USB nRF24 stick firmware (STM32F030): the PC-side radio, see dongle/README.md
|
|
hardware/openscad/ OpenSCAD model of the robot (rebuilt from the Fusion designs) and the new remote
|
|
hardware/openscad/stl/ print-ready STL exports
|
|
hardware/fusion360/ Fusion 360 designs: body, legs, servo, servo horn, remote case
|
|
scripts/ PlatformIO helper (per-environment sketch folder)
|
|
```
|
|
|
|
This is the `2026-current/` folder of the hexapod-robot repo; the earlier
|
|
generations (2009 onwards) are in the folders next to it, see
|
|
[../README.md](../README.md).
|
|
|
|
## Build (PlatformIO)
|
|
|
|
```
|
|
pio run # build both
|
|
pio run -e robot -t upload
|
|
pio run -e remote -t upload
|
|
pio device monitor -e robot
|
|
```
|
|
|
|
## Simulation
|
|
|
|
From this `2026-current` folder in PowerShell (the dev PC is Windows):
|
|
|
|
```
|
|
.\sim\build.ps1 # build hexapod_sim.dll + run the headless firmware checks
|
|
```
|
|
|
|
Then open `Hexapod_Simulation_Unity` and press Play. See
|
|
[sim/README.md](sim/README.md).
|
|
|
|
## Printing the remote (v2)
|
|
|
|
STLs in [hardware/openscad/stl/remote_v2/](hardware/openscad/stl/remote_v2/),
|
|
already in print orientation; everything prints in ASA without supports.
|
|
Regenerate them from `remote_v2.scad` with `-D 'PART="..."'`.
|
|
|
|
| File | Part | Notes |
|
|
|------|------|-------|
|
|
| `remote_v2_top_inlays.3mf` | top shell with both inlays | One object with three parts on filaments 1/2/3: case black, honeycomb red, ON/OFF white. The inlays are the first 3 layers (0.6 mm) of the face-down shell, so the colour swaps only happen there. Made by `hardware/openscad/export_3mf.py` from the three STLs below |
|
|
| `remote_v2_top.stl` + `_inlay.stl` + `_text.stl` | the same, as STLs | Load the three at once and keep them as one multi-part object |
|
|
| `remote_v2_top_multicolor.3mf` | OrcaSlicer project (owner) | all parts on two plates; after re-exporting STLs, update its parts with Orca's "Reload from disk" |
|
|
| `remote_v2_bottom.stl` | bottom shell | flat underside on the bed |
|
|
| `remote_v2_kickstand.stl` | table stand | |
|
|
| `remote_v2_eyelet.stl` | neck-strap eyelet | on the top face (slots to balance it) or on the front edge |
|
|
| `remote_v2_bail.stl` | body brace | swings down and back to rest against your body |
|
|
|
|
Hardware (besides the electronics of the old remote):
|
|
|
|
- 14 x M3 heat-set inserts (4.0 mm hole, ~5.7 mm long): 4 shell screws,
|
|
2 + 2 eyelet (top and front), 2 brace pivots, 4 main-board clamps
|
|
- M3 x 12 x 4 (shells), M3 x 8 button head x 2 (eyelet), M3 x 16 button
|
|
head + washer x 2 (brace), M3 x 8 button head + 7 mm washer x 4 (main
|
|
board clamps, no holes in the board), M3 x 40 + nut (kickstand pin)
|
|
- M2.5 x 14 x 8 (joysticks, into their own boxes), M3 x 5 machine screws x 4
|
|
(display, tap the posts M3), M3 self-tapping x 2 (UPS board), M2 self-tapping x 2 (switch)
|
|
- The display is mounted turned round so its connector clears the Teensy's USB
|
|
plug. `remote.HMI` is generated for that (display direction 270 in the
|
|
Editor's terms, see [remote/NEXTION.md](remote/NEXTION.md)), nothing to set.
|
|
|
|
Design notes, checks and open points: [hardware/openscad/PLANNING.md](hardware/openscad/PLANNING.md).
|
|
|
|
## Planned
|
|
|
|
- **PC radio link:** a USB nRF24L01 stick on the PC as the PC-side radio, on
|
|
the same air settings as the robot and the remote. It's reverse-engineered
|
|
and runs our own firmware (STM32F030 + Si24R1 + AT2401C, updated wire-free
|
|
over USB), see **[dongle/README.md](dongle/README.md)**. Done (2026-11-17):
|
|
its **bridge mode** lets the real remote drive the Unity simulation over the
|
|
air, with the sim's telemetry going back to the remote's display as the ack
|
|
payload ([sim/README.md](sim/README.md), "Using it in Unity"). There's no USB
|
|
link to the remote or the robot any more; everything goes over the radio.
|
|
Still to do:
|
|
- Unity driving the **real** robot (the dongle transmitting instead of
|
|
listening) and mirroring it;
|
|
- three nodes at once: today the dongle answers the remote *instead of* the
|
|
robot. Needs an address per node (or per pipe), a packet type byte, and a
|
|
rule for who has priority. Owner's decisions: the remote wins, with a
|
|
toggle on the remote that hands the robot to Unity and lets the remote's
|
|
sticks control Unity instead; the PC is the hub while it's online, the
|
|
robot is the hub when it isn't; goals: mirror the real robot in Unity,
|
|
drive it from Unity, remote data to the PC, and PC data to the remote.
|
|
- Remote battery level: see [remote/README.md](remote/README.md), "Planned".
|
|
- Robot power: a stable 6 V supply for the 18 servos, see
|
|
[hardware/openscad/PLANNING.md](hardware/openscad/PLANNING.md), "Notes for
|
|
future designs".
|
|
|
|
## Where to go next
|
|
|
|
- **[robot/README.md](robot/README.md)**: placeholder geometry to measure,
|
|
the bench-check checklist, and the serial test harness for driving the
|
|
robot without a remote.
|
|
- **[remote/README.md](remote/README.md)**: wiring, control scheme, stick
|
|
calibration, and the remote's serial console.
|
|
- **[remote/NEXTION.md](remote/NEXTION.md)**: how to build the touchscreen
|
|
HMI.
|
|
- **[shared/HexapodProtocol/HexapodProtocol.h](shared/HexapodProtocol/HexapodProtocol.h)**:
|
|
the protocol. Change it only by reflashing both boards.
|