4 Commits
Author SHA1 Message Date
mangavalkandClaude Opus 5.5 80270ba17e 2026 remote v2: printable bottom shell, notes for the PC radio link
- Bottom shell: the brace pivot bosses stand on pillars and the lip's tie
  band steps out at 45 deg (both were floating overhangs); the kickstand
  barrel sits on the bed. Checked by slicing the STLs layer by layer: only
  bridges are left. STLs re-exported.
- remote_v2_top_multicolor.3mf: now the owner's OrcaSlicer project (all
  parts on two plates); export_3mf.py regenerates the plain multi-part file.
- README "Planned": a USB nRF24 stick on the PC so Unity can talk to both
  the robot and the remote (what to work out), plus pointers to the other
  notes for later.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-14 19:13:28 +01:00
mangavalkandClaude Opus 5.5 60605209fb 2026: remote v2 (flat console for the twist-grip sticks), STL/3MF exports, archive page
remote_v2.scad: a new remote for the same electronics, 216 x 116 x 32 mm,
ASA, two shells printed without supports and joined with M3 heat-set
inserts. Hangs level from a neck strap on a balance-point eyelet (top face
or front edge) with a fold-out body brace; kickstand for the table.
JH-D300X-R1 sticks clamp the plate; main perfboard (Teensy 4.0, nRF24,
IMU) clamped at its sides under the display; UPS board with its LEDs
through the floor. Red honeycomb and white ON/OFF inlays in the first
3 layers. Every part checked for collisions.

- stl/remote_v2/: print-ready STLs, plus a multi-part 3MF (export_3mf.py)
  with the inlays on filaments 2 and 3
- ARCHIVE.md: the original remote with the owner's photos; README shows v2
  and how to print it
- Notes for later: battery-voltage reading, IMU on Wire (18/19) with two
  stick axes moved to A7/A8, a stable 6 V supply for the 18 servos
- remote.scad: its sticks are JH-D300X-R1 (the model uses the D400X drawing)
- *.3mf through Git LFS; repo README says Teensy 4.0 remote

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-14 18:57:49 +01:00
mangavalkandClaude Opus 5.5 e23216b3a1 2026 remote: build for the Teensy 4.0 actually in the remote
Board teensy41 -> teensy40. All pins exist on the 4.0; the MPU6050's
Wire2 (SDA2 25 / SCL2 24) is on the underside solder pads.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-14 12:19:16 +01:00
mangavalkandClaude Opus 5.5 769d72462d 2026 Unity: add editor-generated GDK settings asset and GVH settings
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-14 12:19:15 +01:00
31 changed files with 1002 additions and 24 deletions

No files matched your search

+1
View File
@@ -38,3 +38,4 @@
*.ide-shm filter=lfs diff=lfs merge=lfs -text
2018-unity-sim/**/*.unity filter=lfs diff=lfs merge=lfs -text
*.bytes filter=lfs diff=lfs merge=lfs -text
*.3mf filter=lfs diff=lfs merge=lfs -text
+5 -5
View File
@@ -10,7 +10,7 @@ before changing anything.
```
robot/ Teensy 3.6 firmware (PlatformIO env robot)
remote/ Teensy 4.1 firmware (PlatformIO env remote)
remote/ Teensy 4.0 firmware (PlatformIO env remote)
shared/HexapodProtocol/ wire protocol, used by robot, remote and sim
sim/ robot firmware -> hexapod_sim.dll (CMake + g++), headless smoke test
Hexapod_Simulation_Unity/ Unity 6000.6 project that loads the DLL (Assets/HexapodSim/)
@@ -34,7 +34,7 @@ PlatformIO, one `platformio.ini`, two environments:
| Env | Board | Sketch dir | Purpose |
|-----|-------|------------|---------|
| `robot` | `teensy36` | `robot/` | walking robot |
| `remote` | `teensy41` | `remote/` | handheld transmitter |
| `remote` | `teensy40` | `remote/` | handheld transmitter |
- `shared/` is PlatformIO's `lib_dir`. `shared/HexapodProtocol/` is a
header-only library both sketches `#include <HexapodProtocol.h>`.
@@ -108,7 +108,7 @@ joint-rate clamp → servos.
| `Comms` | nRF24 RX, link timeout, `injectPacket()` for the harness |
| `ServoDriver` | 18 servos on hardware PWM (50 Hz, 16-bit), per-servo calibration from `Config.h` `SERVOS`, duty 0 = relaxed, skips invalid IK solutions |
## Remote architecture (`remote/`, Teensy 4.1)
## Remote architecture (`remote/`, Teensy 4.0)
Loop: drain Nextion + USB serial input every pass. On each `TX_HZ` (100)
tick: sticks → IMU → radio link status → RemoteState (smoothers,
@@ -366,7 +366,7 @@ Robot (`robot/README.md` has detail):
Remote (`remote/README.md` has detail):
- Pins in `remote/Config.h`, taken from the old remote sketch: radio CE 9 /
CSN 10, sticks A0–A5, Nextion on Serial1 (0/1). The MPU6050 is on
**Wire2 (25/24)**, since A4/A5 = Wire's SDA/SCL are stick pins; that's
**Wire2 (25/24, solder pads under the Teensy 4.0)**, since A4/A5 = Wire's SDA/SCL are stick pins; that's
the owner's choice and needs rewiring the MPU. Which stick axis is on
which pin is still unknown.
- `STICK_INVERT[]`, calibration defaults, deadzones, expo.
@@ -393,7 +393,7 @@ Remote (`remote/README.md` has detail):
- `b2` → **Nextion upload passthrough**: shows `uploadscreen`, then
bridges USB ↔ Serial1 forever, so Nextion Editor can upload a `.tft`
through the remote's USB port. The new firmware keeps this.
- Sticks on **A0–A5**, contiguous (`analogInPin + i`). On the Teensy 4.1,
- Sticks on **A0–A5**, contiguous (`analogInPin + i`). On the Teensy 4.0,
A4/A5 are pins 18/19 = Wire SDA/SCL, which the MPU6050 needs. The old
code had the MPU code disabled (`if (false)`). Owner's decision: keep
the sticks, move the MPU to Wire2.
@@ -0,0 +1,8 @@
fileFormatVersion: 2
guid: fc34dbb2de5c9264996b3a62ab44041a
folderAsset: yes
DefaultImporter:
externalObjects: {}
userData:
assetBundleName:
assetBundleVariant:
@@ -0,0 +1,15 @@
%YAML 1.1
%TAG !u! tag:unity3d.com,2011:
--- !u!114 &11400000
MonoBehaviour:
m_ObjectHideFlags: 0
m_CorrespondingSourceObject: {fileID: 0}
m_PrefabInstance: {fileID: 0}
m_PrefabAsset: {fileID: 0}
m_GameObject: {fileID: 0}
m_Enabled: 1
m_EditorHideFlags: 0
m_Script: {fileID: 11500000, guid: 84c25d82fb814954a15a26feee052c98, type: 3}
m_Name: GDKEdition
m_EditorClassIdentifier: Unity.Microsoft.GDK::Unity.XGamingRuntime.GdkEditionAsset
m_EditionNumber: -1
@@ -0,0 +1,8 @@
fileFormatVersion: 2
guid: 191b1a487084bf849be4570078df21cc
NativeFormatImporter:
externalObjects: {}
mainObjectFileID: 11400000
userData:
assetBundleName:
assetBundleVariant:
+63 -3
View File
@@ -1,10 +1,14 @@
# Hexapod
A six-legged walking robot (Teensy 3.6) and its handheld remote
(Teensy 4.1 + Nextion touchscreen), linked over nRF24L01.
(Teensy 4.0 + Nextion touchscreen), linked over nRF24L01.
![The hexapod, OpenSCAD model in its standing pose](hardware/openscad/renders/hexapod.png)
![The remote, OpenSCAD model](hardware/openscad/renders/remote.png)
![The remote (v2), OpenSCAD model: black ASA with a red honeycomb and white ON/OFF inlay](hardware/openscad/renders/remote_v2.png)
The remote above is the new design (`hardware/openscad/remote_v2.scad`, not
printed yet). The original printed remote is on the
[archive page](hardware/openscad/ARCHIVE.md).
```
robot/ robot firmware: IK, gait, body pose, IMU stabilization, state machine
@@ -12,7 +16,8 @@ remote/ remote firmware: 2 x 3-axis sticks, MPU6050 tilt, Nex
shared/ HexapodProtocol: the CmdPacket wire format + radio settings used by both
sim/ the unchanged robot firmware compiled into a DLL for the simulation
Hexapod_Simulation_Unity/ Unity project that runs that DLL on the 3D model
hardware/openscad/ OpenSCAD model of the robot and remote, rebuilt from the Fusion designs
hardware/openscad/ OpenSCAD model of the robot (rebuilt from the Fusion designs) and the new remote
hardware/openscad/stl/ print-ready STL exports
hardware/fusion360/ Fusion 360 designs: body, legs, servo, servo horn, remote case
scripts/ PlatformIO helper (per-environment sketch folder)
```
@@ -41,6 +46,61 @@ From this `2026-current` folder in PowerShell (the dev PC is Windows):
Then open `Hexapod_Simulation_Unity` and press Play. See
[sim/README.md](sim/README.md).
## Printing the remote (v2)
STLs in [hardware/openscad/stl/remote_v2/](hardware/openscad/stl/remote_v2/),
already in print orientation; everything prints in ASA without supports.
Regenerate them from `remote_v2.scad` with `-D 'PART="..."'`.
| File | Part | Notes |
|------|------|-------|
| `remote_v2_top_multicolor.3mf` | top shell with both inlays | One object with three parts on filaments 1/2/3: case black, honeycomb red, ON/OFF white. The inlays are the first 3 layers (0.6 mm) of the face-down shell, so the colour swaps only happen there. Made by `hardware/openscad/export_3mf.py` from the three STLs below |
| `remote_v2_top.stl` + `_inlay.stl` + `_text.stl` | the same, as STLs | Load the three at once and keep them as one multi-part object |
| `remote_v2_bottom.stl` | bottom shell | flat underside on the bed |
| `remote_v2_kickstand.stl` | table stand | |
| `remote_v2_eyelet.stl` | neck-strap eyelet | on the top face (slots to balance it) or on the front edge |
| `remote_v2_bail.stl` | body brace | swings down and back to rest against your body |
Hardware (besides the electronics of the old remote):
- 14 x M3 heat-set inserts (4.0 mm hole, ~5.7 mm long): 4 shell screws,
2 + 2 eyelet (top and front), 2 brace pivots, 4 main-board clamps
- M3 x 12 x 4 (shells), M3 x 8 button head x 2 (eyelet), M3 x 16 button
head + washer x 2 (brace), M3 x 8 button head + 7 mm washer x 4 (main
board clamps, no holes in the board), M3 x 40 + nut (kickstand pin)
- M2.5 x 14 x 8 (joysticks, into their own boxes), M2.5 self-tapping x 4
(display), M3 self-tapping x 2 (UPS board), M2 self-tapping x 2 (switch)
- Set the Nextion's display direction to 180 in the Nextion Editor: the
display is mounted turned round so its connector clears the Teensy's USB plug.
Design notes, checks and open points: [hardware/openscad/PLANNING.md](hardware/openscad/PLANNING.md).
## Planned
- **PC radio link (owner, later):** a USB nRF24L01 stick on the PC (it
probably shows up as a serial port), on the same radio as the robot and the
remote, so Unity on the PC can both receive data from (telemetry) and send
data to the robot and the remote. Not designed yet. To work out:
- what the stick's firmware does: many of these sticks are a USB-serial
chip with a microcontroller set up by AT commands (address, channel, data
rate) that passes raw payloads through; check that it can match
`HXP_RADIO_*` in `shared/HexapodProtocol/HexapodProtocol.h` (channel 96,
250 kbps, 5-byte address `HXPD1`, fixed payload of `sizeof(CmdPacket)`)
and whether it can do auto-ack and ack payloads;
- the radio protocol: today the remote only transmits a `CmdPacket` to the
robot and nothing comes back. Three nodes need an address per node (or
per pipe), a packet type byte, and telemetry back (e.g. as ack payloads
or in time slots) so the nodes don't talk over each other; who has
priority when the PC and the remote both send commands;
- Unity side: a serial-port reader/writer next to the simulation (the
2019 generation already drove the robot from Unity, through the remote
over USB: see `../2019-teensy-nrf24/`).
- Remote battery level and the IMU on the normal pin headers: see
[remote/README.md](remote/README.md), "Planned".
- Robot power: a stable 6 V supply for the 18 servos, see
[hardware/openscad/PLANNING.md](hardware/openscad/PLANNING.md), "Notes for
future designs".
## Where to go next
- **[robot/README.md](robot/README.md)**: placeholder geometry to measure,
+37
View File
@@ -0,0 +1,37 @@
# Archive: earlier designs
Designs that are no longer the current ones, kept for reference. The
current remote is `remote_v2.scad` (see [../../README.md](../../README.md)).
## Original remote (`remote.scad`)
![The original remote, OpenSCAD model](renders/remote.png)
The remote used with the robot until 2026: a 208 x 175 x 45 mm box printed
from the Fusion 360 design `../fusion360/remote/remote v40.f3d`.
`remote.scad` rebuilds it from that file's solids (details, and the bugs
fixed in the rebuild, in [PLANNING.md](PLANNING.md), section "Remote").
What's inside (from the owner and the photos below):
- Two joysticks, JH-D300X-R1 (3-axis twist grip), on the lid. The model
uses the similar JH-D400X-R4 drawing.
- Nextion NX4832T035 3.5" display under a window in the lid.
- A Teensy 4.0 socketed on a cut perfboard with the nRF24L01 (100 uF cap)
and an AMS1117 regulator.
- An MPU6050 (GY-521) on the big standoff in the middle.
- An 18650 UPS/boost board on two standoffs, with its charge and on LEDs
visible through two small slots in the floor.
- A USB-C breakout glued into the holder at the side port.
- A slide switch mounted on top of the lid, and a lanyard loop on the bump.
Photos of the printed remote, opened: [original remote/](original%20remote/).
| | |
|---|---|
| ![Lid from inside: Nextion and joysticks](original%20remote/20261114_175520.jpg) | ![Bottom shell: main board, battery, IMU, USB-C](original%20remote/20261114_175548.jpg) |
| ![Main board, top](original%20remote/20261114_175504.jpg) | ![Main board, wiring underneath](original%20remote/20261114_175509.jpg) |
Why it was replaced: the new remote (`remote_v2.scad`) is smaller
(216 x 116 x 32 mm), prints in ASA without supports, hangs level from a neck
strap (a balance-point eyelet and a body brace), and stands on a table.
+88 -3
View File
@@ -118,7 +118,7 @@ mm (sat in the ledge, posts overlapping the bosses); the display bezel's
mesh facets became a clean window; the stray Body12 (an ON-OFF bracket
line never cut in) is left out. The display is a Nextion NX4832T035
(3.5" Basic); its board's M3 holes are the lid's 94.2 x 48.5 post grid.
Reference parts in `remote.scad`: the joysticks are JH-D400X-R4 (4-axis,
Reference parts in `remote.scad`: the joysticks are modelled as JH-D400X-R4 (owner's photos later showed JH-D300X-R1; 4-axis,
X/Y ±25°, twist ±45°, button; owner), mounted with the dust cover on the
lid's top face; their M2.5 square is 32.5 mm, so the lid's screw holes moved
from the original's 33 mm square to 32.5. The battery is an 18650 UPS/boost
@@ -129,14 +129,99 @@ Also from the owner: the bump on top of the middle post is a lanyard loop
(the original's tunnel through it is modelled); the square hole is the on/off
slide switch, mounted on top (same switch as the robot). Inside: an IMU on the
21 x 9 mm block (assumed GY-521), a USB-C breakout on the side-port block, and
a Teensy **4.0** (confirmed by the owner, although `platformio.ini` builds
the remote for a 4.1); it has no mounting holes and is placed on the
a Teensy **4.0** (confirmed by the owner; `platformio.ini` now builds
the remote for it); it has no mounting holes and is placed on the
hole-less 8 x 24 mm block as a guess.
Open: what the 6 mm x 10 mm holes in the bottom bosses hold (magnets?), and
whether the upper two bosses are meant to be asymmetric (x -80.387 / +82.73).
## Remote v2 (`remote_v2.scad`), draft 4
A new remote for the same electronics; `remote.scad` stays as the record of
the printed one. How it's used (owner): the sticks are big twist grips that
take a whole hand each, so nothing holds the case. It hangs from a neck strap
or lies on a table. Earlier drafts: gamepad grips (dropped: nobody holds
them), strap tabs at the rear corners (it tipped forward), a hexapod emblem
inlay (owner preferred a honeycomb).
From the owner's photos and drawing: the sticks are JH-D300X-R1; the Teensy
sits socketed on a cut perfboard (~52 x 80, estimated) with the nRF24L01
(100 uF cap), an AMS1117, the ribbon connectors and now also the GY-521; the
switch's plate sits on top of the case, body through the slot, and the old
8 x 16 slot with d2 holes 19 mm apart fits it exactly; the UPS board's
charge/on LEDs show through two slots in the floor.
- Size 216 x 116 x 32 mm (old remote: 208 x 175 x 45). Sticks at u +-80,
display forward of them, strap eyelet behind the display, UPS board behind
that, switch at the rear centre. Main board under the display.
- JH-D300X-R1: dust cover d53.5 on the top face; the 40.4 mm control box
(25.5 tall) against the plate's underside, 4 x M2.5 x 14 through cover and
plate into the box (no nuts). Reaches 28.5 mm down. Pots (d16.5, 9.2 out)
towards the middle and towards the user.
- Display mounted turned 180 deg so its J1 connector is on the right, clear
of the Teensy's USB plug: set display direction 180 in the Nextion Editor.
Glass 1.5 mm under the top face, board on 4 posts (M2.5 self-tapping);
the LCD thickness (4.5) is a guess.
- Main board clamped at 4 points on its long sides, no holes in the board
(owner): posts beside the edges carry it, M3 x 8 button heads with d7
washers in heat-set inserts clamp the edge. 2 mm above the kickstand
recess for the wires underneath; Teensy micro-USB to the left, nRF24 to
the right. The cable plug clears the display board by ~0.2 mm and the left
stick's pot narrowly: plug and board sizes are estimates.
- UPS board on 2 standoffs behind the eyelet, Type-C end to the right (room
for the cut cable's plug); LEDs through 2 x 6 mm floor slots.
- Strap eyelet (separate part, 2 x M3 into heat-set inserts): on the top face
behind the display (slots +-5 mm to balance it), or on the front face (the
edge away from you, 2 more inserts at Z -19). Folded forward, the bail
hits a front-mounted eyelet: then park the bail back or down.
- Brace bail: U pivoting on the side faces (v -25, Z -22), M3 x 16 into
heat-set inserts; 0 = folded forward, -150 = brace against chest or belly,
-180 = straight back. Swings down under the case.
- Kickstand: 30 x 35 mm flap in a recess in the underside, hinged at the front
on an M3 x 40 into a nut trap; lifts the front a little on a table.
- Shells split at Z -12, both print without supports (top face down, bottom
on its flat underside), 45 deg chamfers, 1.2 mm locating lip, 4 x M3 x 12
from below into heat-set inserts. USB-C breakout glued into a pocket at
the front left, receptacle 0.6 mm inside the front face.
- Inlay (second colour, first 3 layers of the face-down top shell): ON/OFF
plus a honeycomb of whole cells (4.5 mm, 1.2 mm walls) right of a diagonal
through the middle, clear of display, sticks, eyelet and switch; lone
cells dropped. Colours (owner, ASA): black case, red honeycomb (PART
"inlay"), white ON/OFF (PART "text"); load "top", "inlay" and "text" as one
multi-part object. Each extra colour adds a swap on the first 3 layers only.
- Printability (the STLs sliced in 0.2 mm layers, every area not carried by
the layer below listed): the brace pivot bosses stand on pillars and the
lip's tie band steps out at 45 deg (both were floating overhangs in the
first export); what's left are bridges: the 30 mm kickstand-recess roof,
the hinge trough, hole and counterbore tops, the USB-C opening.
- Checked: no part collides with the shells or with each other, the shells
and the inlay don't overlap, kickstand clear at 0 and 70 deg, bail clear
from 0 to -180 deg (CGAL intersections).
- Open: perfboard size and holes, Teensy cable plug size, LCD thickness, UPS
hole spacing; hand room untested; set `IMU_AXIS_FROM_CHIP` /
`IMU_AXIS_SIGN` in `remote/Config.h` for the IMU on the main board.
## Notes for future designs
- Robot power (still to choose): a battery or supply that gives a **stable
6 V** with enough current for all 18 servos (12 x HS-485HB + 6 stronger
ones of the same size). Servos draw well over 1 A each when stalled or
starting, and many move at once while walking, so plan for a 6 V regulator
/ UBEC of 15-20 A peak (e.g. a 2S LiPo through a high-current 6 V BEC), or
a pack that stays near 6 V under that load. Check the servos' datasheet
for the stall current. The battery must also fit the bay (see open
question 3) and leave room for the servo plugs.
- Remote: connect the IMU to the normal pin headers instead of the Teensy
4.0's underside pads; see `remote/README.md`, "Planned" (Wire on 18/19,
the two stick axes there move to A7/A8).
- Remote: measure the 18650's voltage on the Teensy to show how much charge
is left (owner, later). Divider ~100k/100k from the cell's + (holder or the
UPS board's B+, not the 5 V output) to A6 (pin 20, free), 100 nF to GND;
full cell = ~2.1 V at the pin. Firmware: average, Li-ion curve to %, show
on the Nextion with a low-battery warning (optionally send it to the robot).
- Servo wires barely fit on the real robot: the six servo headers hang
above the battery bay, and the front pair sits right over the bay's end
stop (X 28.8..31.8, top at Z 13.5). Kept as-is for now; give the plugs and
@@ -0,0 +1,115 @@
"""Combine STL parts into one multi-part 3MF for OrcaSlicer / PrusaSlicer.
python export_3mf.py (from hardware/openscad, after the STL export)
Writes stl/remote_v2/remote_v2_top_multicolor.3mf: the top shell with its
two inlays as ONE object with three parts, in the same frame, each part on
its own extruder/filament (1 = case, 2 = honeycomb, 3 = ON/OFF text). The
part list is in PARTS below. Uses the PrusaSlicer 3MF layout (one mesh, the
parts as triangle ranges in Metadata/Slic3r_PE_model.config), which
OrcaSlicer and PrusaSlicer both read.
"""
import os
import zipfile
HERE = os.path.dirname(os.path.abspath(__file__))
OUT_DIR = os.path.join(HERE, "stl", "remote_v2")
# (file, part name, extruder)
PARTS = [
("remote_v2_top.stl", "top shell (black)", 1),
("remote_v2_inlay.stl", "honeycomb inlay (red)", 2),
("remote_v2_text.stl", "ON-OFF inlay (white)", 3),
]
OUT = "remote_v2_top_multicolor.3mf"
def read_stl(path):
"""Triangles of an ASCII or binary STL as lists of 3 vertex tuples."""
data = open(path, "rb").read()
tris = []
if data[:5] == b"solid" and b"facet" in data[:400]:
verts = []
for line in data.decode("ascii", "replace").splitlines():
t = line.split()
if t and t[0] == "vertex":
verts.append(tuple(float(x) for x in t[1:4]))
if len(verts) == 3:
tris.append(verts)
verts = []
else:
import struct
n = struct.unpack_from("<I", data, 80)[0]
for i in range(n):
f = struct.unpack_from("<12f", data, 84 + 50 * i)
tris.append([tuple(f[3:6]), tuple(f[6:9]), tuple(f[9:12])])
return tris
def main():
vertices, index, triangles, ranges = [], {}, [], []
for fname, name, extruder in PARTS:
first = len(triangles)
for tri in read_stl(os.path.join(OUT_DIR, fname)):
ids = []
for v in tri:
key = (round(v[0], 5), round(v[1], 5), round(v[2], 5), len(ranges)) # no sharing between parts
if key not in index:
index[key] = len(vertices)
vertices.append(v)
ids.append(index[key])
if len(set(ids)) == 3:
triangles.append(ids)
ranges.append((first, len(triangles) - 1, name, extruder))
model = ['<?xml version="1.0" encoding="UTF-8"?>',
'<model unit="millimeter" xml:lang="en-US" '
'xmlns="http://schemas.microsoft.com/3dmanufacturing/core/2015/02" '
'xmlns:slic3rpe="http://schemas.slic3r.org/3mf/2017/06">',
' <metadata name="slic3rpe:Version3mf">1</metadata>',
' <metadata name="Title">remote_v2 top shell with inlays</metadata>',
' <resources>',
' <object id="1" type="model">',
' <mesh>',
' <vertices>']
model += [' <vertex x="%.5f" y="%.5f" z="%.5f"/>' % v for v in vertices]
model += [' </vertices>', ' <triangles>']
model += [' <triangle v1="%d" v2="%d" v3="%d"/>' % tuple(t) for t in triangles]
model += [' </triangles>', ' </mesh>', ' </object>', ' </resources>',
' <build>', ' <item objectid="1"/>', ' </build>', '</model>']
config = ['<?xml version="1.0" encoding="UTF-8"?>', '<config>',
' <object id="1" instances_count="1">',
' <metadata type="object" key="name" value="remote_v2_top_multicolor"/>']
for first, last, name, extruder in ranges:
config += [' <volume firstid="%d" lastid="%d">' % (first, last),
' <metadata type="volume" key="name" value="%s"/>' % name,
' <metadata type="volume" key="volume_type" value="ModelPart"/>',
' <metadata type="volume" key="extruder" value="%d"/>' % extruder,
' </volume>']
config += [' </object>', '</config>']
content_types = ('<?xml version="1.0" encoding="UTF-8"?>\n'
'<Types xmlns="http://schemas.openxmlformats.org/package/2006/content-types">\n'
' <Default Extension="rels" ContentType="application/vnd.openxmlformats-package.relationships+xml"/>\n'
' <Default Extension="model" ContentType="application/vnd.ms-package.3dmanufacturing-3dmodel+xml"/>\n'
' <Default Extension="config" ContentType="text/xml"/>\n'
'</Types>\n')
rels = ('<?xml version="1.0" encoding="UTF-8"?>\n'
'<Relationships xmlns="http://schemas.openxmlformats.org/package/2006/relationships">\n'
' <Relationship Target="/3D/3dmodel.model" Id="rel0" '
'Type="http://schemas.microsoft.com/3dmanufacturing/2013/01/3dmodel"/>\n'
'</Relationships>\n')
path = os.path.join(OUT_DIR, OUT)
with zipfile.ZipFile(path, "w", zipfile.ZIP_DEFLATED) as z:
z.writestr("[Content_Types].xml", content_types)
z.writestr("_rels/.rels", rels)
z.writestr("3D/3dmodel.model", "\n".join(model) + "\n")
z.writestr("Metadata/Slic3r_PE_model.config", "\n".join(config) + "\n")
print("%s: %d vertices, %d triangles, parts %s" % (OUT, len(vertices), len(triangles),
", ".join("%s %d-%d" % (r[2], r[0], r[1]) for r in ranges)))
if __name__ == "__main__":
main()
+3 -2
View File
@@ -150,8 +150,9 @@ module nextion_3_5() {
color("#3050a0") translate([win[0] - 73.44/2, win[1] - 48.96/2, DISPLAY_POCKET_Z - 0.2]) cube([73.44, 48.96, 0.2]);
}
// JH-D400X-R4 4-axis joystick (X/Y +-25 deg, twist +-45 deg, button),
// from its dimension drawing. Mounted with its dust cover on the lid's top
// Joystick, modelled from the JH-D400X-R4 drawing (4-axis, X/Y +-25 deg,
// twist +-45 deg, button). The remote's sticks turned out to be JH-D300X-R1
// (label on the box, owner's photo): similar, dimensions not checked yet. Mounted with its dust cover on the lid's top
// face; the body hangs through the d40 opening. Local frame: stick axis on
// Z, Z = 0 on the dust cover's underside. Pots on +X and +Y.
JOY_COVER_D = 53.5;
@@ -0,0 +1,583 @@
// Remote v2: a flat console for the same electronics as the original remote
// (remote.scad, kept as the record of the printed one). Draft 3, not printed.
//
// Use (owner): both hands wrap the big twist-grip sticks, so nothing holds
// the case. It hangs from a neck strap on one eyelet on the top face, near
// the balance point and behind the display (slide it in its slots to balance),
// with a fold-out bail that braces against the body; or it lies on a table on
// its kickstand. The sticks sit far apart and nothing rises above the top face
// near them.
//
// Two shells split horizontally, printed in ASA: the top shell face down,
// the bottom shell on its flat underside, both without supports. The
// kickstand, strap eyelet and brace bail are separate parts. The shells are joined by M3 screws from below
// into heat-set inserts in the top shell.
//
// Frame: u to the right, v away from the user (the far edge is the front),
// Z up, Z = 0 on the top face.
//
// Electronics (all reused): 2 x JH-D300X-R1 joystick, Nextion NX4832T035
// (3.5"), 18650 UPS/boost board (89 x 22), Teensy 4.0, GY-521 (MPU6050),
// 12 x 15 mm 4-pin USB-C breakout (V, D-, D+, G), slide switch (the robot's).
// Wiring (owner): the breakout's V/G go to the UPS board's charge input and
// D-/D+ to the Teensy, through two halves of a cut USB cable whose plugs go
// into the UPS board and the Teensy; the UPS output feeds the Teensy.
/* [Shell] */
T = 2.4; // walls and floor (6 perimeters of 0.4)
PLATE = 3.0; // top plate
Z_BOT = -32; // flat underside (32 mm thick: the D300X sticks reach 28.5 down)
Z_SPLIT = -12; // top shell / bottom shell
CHAMFER = 4; // 45 deg bottom edge (printable without support)
TOP_CHAMFER = 1.5; // 45 deg top edge (the top shell prints face down)
LIP_H = 2.5; // locating lip on the bottom shell, into the top shell
LIP_W = 1.2;
FIT = 0.2; // clearance per side between printed parts
/* [Outline] */
STICKS = [[-80, 0], [80, 0]];
STICK_SQ = [28, 40]; // half size (u, v) of the rounded box around each stick
STICK_SQ_R = 10;
FRONT_BAND = [[-60, 0], [60, 52]]; // u, v box: display, USB-C, Teensy
FRONT_V = FRONT_BAND[1][1];
SIDE_U = STICKS[1][0] + STICK_SQ[0]; // the flat side faces
REAR_BAND = [[-80, -64], [80, 0]]; // UPS board behind the strap eyelet, switch behind that
CORNER_R = 10;
/* [Fasteners] */
// M3 x 12 from below; heat-set insert M3 (4.0 mm hole, 5.7 mm long) in the top shell
SCREWS = [[-58, 32], [58, 32], [-70, -52], [70, -52]];
BOSS_D = 9;
INSERT_D = 4.0;
INSERT_L = 6;
SCREW_D = 3.4;
HEAD_D = 6.5;
HEAD_Z = -19; // counterbore floor: 7 mm of tower + 5 mm into the insert
/* [Joysticks] */
STICK_HOLE_D = 40;
STICK_SCREW = 16.25; // 4 x M2.5 x 14 on a 32.5 mm square, through cover and plate into the control box
STICK_SCREW_D = 2.8;
/* [Display: Nextion NX4832T035] */
NX_BOARD = [100.5, 54.94];
NX_HOLES = [94.2, 48.5]; // M3 grid, centred on the board
NX_CENTRE = [0, 20]; // board centre (forward of the sticks, so the strap misses it)
NX_FLIP = true; // display mounted turned 180 deg (its J1 connector on the right, clear of
// the Teensy's USB plug): set display direction 180 in the Nextion Editor
NX_WIN_OFF = [NX_FLIP ? 2.15 : -2.15, 0]; // window (visible area) centre from the board centre
NX_WINDOW = [75.9, 50.9]; // opening in the plate
NX_LCD = [84, 54]; // LCD module outline
NX_LCD_T = 4.5; // LCD thickness: approximate, measure before printing
NX_BEZEL = 1.5; // plate left above the glass
NX_POST_D = 5.5; // clears the LCD module by 0.2 mm
NX_SCREW_D = 2.2; // M2.5 self-tapping through the board
/* [Switch: slide switch, mounted on top] */
SWITCH_POS = [0, -56];
SWITCH_SLOT = [16, 8]; // 8 x 16 slot and d2 holes 19 apart: fit the switch exactly (owner, old remote)
SWITCH_PITCH = 19;
SWITCH_HOLE_D = 2.0;
ENGRAVE_D = 0.6; // ON/OFF inlay: the first 3 layers (0.2) of the face-down top shell
/* [USB-C breakout] */
USBC_BOARD = [12, 15, 1.6];
USBC_RCPT = [8.94, 7.35, 3.26]; // receptacle, flush with the board's front edge
USBC_POS = [-45, 0]; // board centre u (v follows from the front wall)
USBC_Z = Z_BOT + 10; // board underside
/* [Other boards] */
UPS_CENTRE = [0, -41];
UPS_LEDS = [[-23.9, 0], [23.9, 0]]; // charge / on LEDs, seen through 2 x 6 mm floor slots (as on the old remote)
UPS_HOLES = 27.9; // +- u, not confirmed (same as the old remote)
UPS_Z = Z_BOT + T + 2; // board underside (2 mm standoffs); its top ends 2 mm under the plate
/* [Main board: perfboard with the Teensy 4.0 (socketed), nRF24L01, AMS1117] */
// Cut perfboard, 19 x 30 holes. Size and corner holes are estimates from the
// owner's photos: measure before printing. Board frame: x across (0..52), y
// along (0..80), Teensy micro-USB at y 0, nRF24 overhanging at y 80.
PERF = [52, 80, 1.6];
// Held by 4 clamps on its long sides, no holes in the board (owner): a post
// beside the edge carries the board's edge on its inner half, and an M3 x 8
// button head with a washer (d7) in a heat-set insert in the post clamps it.
PERF_CLAMPS = [[0, 4], [0, 68], [52, 4], [52, 68]]; // board frame: on the edges x = 0 / 52, at these y
PERF_CLAMP_OUT = 1.5; // post centre outside the board edge (washer overlaps the board ~2 mm)
PERF_POS = [-36, 37]; // where the board's (0, 0) corner goes; x runs to -v, y to +u
PERF_Z = Z_BOT + 7.5; // board underside: 2 mm over the kickstand recess roof for wires (the Teensy USB plug then clears the display board)
PERF_IMU = [23, 38]; // GY-521 on the main board (owner), on 8.5 mm headers: its corner, board frame
/* [Kickstand] */
KS_W = 30; // flap width (u)
KS_V = [8, 43.75]; // free end, hinge axis (the trough clears the main board)
KS_T = 3;
KS_BARREL_D = 6.5;
KS_PIN_D = 3.3; // M3 x 40 screw, from inside on the left, into a nut trap on the right
KS_WALL = 3; // side walls (nut trap)
KS_WALL_V = 2; // front/back walls
/* [Strap eyelet] */
// A loop on the top face for the neck strap's snap hook, near the balance
// point (estimated centre of mass v -3, Z -18: with the eyelet at v -24 the
// remote hangs level when the strap leaves at ~34 deg from vertical).
// Two M3 x 8 button heads into heat-set inserts; the slots give
// +-HOOK_TRAVEL to balance it.
HOOK_POS = [0, -24];
HOOK_TRAVEL = 5;
HOOK_INSERTS = 7; // +- u
HOOK_BASE = [24, 18, 4]; // u, v, Z
// Alternative place: the front face (the edge away from you), 2 inserts in
// the front wall of the bottom shell; the loop then points forward.
HOOK_FRONT_Z = -19;
HOOK_MOUNT = "top"; // [top, front] (assembly view only)
HOOK_HOLE_D = 8; // for the snap hook
HOOK_H = 16; // top of the loop above the top face
/* [Brace bail] */
// A U-shaped bail pivoting on the side faces, outside the case and below the
// hands. Folded forward it wraps the front edge; swung back and down its
// crossbar rests against your chest or belly. M3 x 16 button-head screws
// with a washer into heat-set inserts in the side walls; friction holds it.
BAIL_PIVOT = [-25, -22]; // v, Z on the side faces (u +-SIDE_U)
BAIL_L = 82; // pivot to crossbar centre line
BAIL_BOW = 10; // crossbar bows outwards by this much in the middle
BAIL_T = 5; // arm thickness (u)
BAIL_H = 12; // arm and crossbar height
BAIL_GAP = 0.5; // arm to side face (a washer fills it)
BAIL_ANGLE = 0; // 0 = folded forward, swings down: -90 hanging, -180 straight back, ~-150 brace
/* [Rendering] */
PART = "assembly"; // [assembly, top, inlay, text, bottom, kickstand, eyelet, bail]
SHOW_TOP = true;
SHOW_BOTTOM = true;
SHOW_PARTS = true;
SHOW_STICKS = true;
KS_OPEN = 0; // kickstand angle, deg
EXPLODE = 0;
/* [Hidden] */
$fa = 4; $fs = 0.5;
BIG = 400;
JOIN = 1;
module lx(h) linear_extrude(h, convexity = 10) children();
module rbox(b, r) translate(b[0] + [r, r]) offset(r = r) square(b[1] - b[0] - [2 * r, 2 * r]);
module rsq(c, h, r) translate(c) offset(r = r) square(2 * (h - [r, r]), center = true);
// ---------- outline and solid ----------------------------------------------
module outline_2d() hull() {
rbox(FRONT_BAND, CORNER_R);
rbox(REAR_BAND, CORNER_R);
for (s = STICKS) rsq(s, STICK_SQ, STICK_SQ_R);
}
// The outline swept with a 45 deg chamfer at the bottom (and optionally at
// the top): a thin slab of the outline, inset by the chamfer, Minkowski'd
// with a turned profile. `inset` gives the inner surface of the walls.
module swept(inset, z0, z1, top_chamfer) {
c = CHAMFER;
h = z1 - z0;
tc = top_chamfer;
minkowski() {
translate([0, 0, z0]) linear_extrude(0.01) offset(delta = -(c + inset)) outline_2d();
rotate_extrude($fn = 32) polygon([[0, 0], [c, c], [c, h - tc], [c - tc, h], [0, h]]);
}
}
module outer_solid() swept(0, Z_BOT, 0, TOP_CHAMFER);
module inner_solid() swept(T, Z_BOT + T, BIG / 4, 0);
// ---------- top shell -------------------------------------------------------
module nx_holes() for (du = [-1, 1], dv = [-1, 1]) translate(NX_CENTRE + [du * NX_HOLES[0], dv * NX_HOLES[1]] / 2) children();
module stick_screws() for (s = STICKS, du = [-1, 1], dv = [-1, 1]) translate(s + [du, dv] * STICK_SCREW) children();
NX_WIN = NX_CENTRE + NX_WIN_OFF;
NX_BOARD_TOP = -NX_BEZEL - NX_LCD_T; // board's top face
module top_shell() render(convexity = 10) difference() {
union() {
intersection() {
outer_solid();
difference() {
translate([-BIG / 2, -BIG / 2, Z_SPLIT]) cube([BIG, BIG, -Z_SPLIT]);
difference() { inner_solid(); translate([-BIG / 2, -BIG / 2, -PLATE]) cube(BIG); }
}
}
// eyelet inserts
for (m = [-1, 1]) translate([HOOK_POS[0] + m * HOOK_INSERTS, HOOK_POS[1], -PLATE - 7 + JOIN]) cylinder(d = 8, h = 7);
// screw bosses
for (s = SCREWS) translate([s[0], s[1], Z_SPLIT]) cylinder(d = BOSS_D, h = -Z_SPLIT - PLATE + JOIN);
// display posts
nx_holes() translate([0, 0, NX_BOARD_TOP]) cylinder(d = NX_POST_D, h = -NX_BOARD_TOP - PLATE + JOIN);
// joystick nut bosses
}
// display: window (chamfered to the top) and LCD pocket
translate(concat(NX_WIN, -NX_BEZEL - 0.01)) hull() {
translate([0, 0, 0.005]) cube(concat(NX_WINDOW, 0.01), center = true);
translate([0, 0, NX_BEZEL + 0.01]) cube(concat(NX_WINDOW + [2, 2] * NX_BEZEL, 0.02), center = true);
}
translate(concat(NX_WIN - (NX_LCD + [1, 1]) / 2, -PLATE - 1)) cube(concat(NX_LCD + [1, 1], PLATE + 1 - NX_BEZEL));
nx_holes() translate([0, 0, NX_BOARD_TOP - 1]) cylinder(d = NX_SCREW_D, h = 1 + 4.5);
// joysticks
for (s = STICKS) translate([s[0], s[1], -BIG / 2]) cylinder(d = STICK_HOLE_D, h = BIG);
stick_screws() translate([0, 0, -BIG / 2]) cylinder(d = STICK_SCREW_D, h = BIG);
// switch
translate(SWITCH_POS) {
translate([-SWITCH_SLOT[0] / 2, -SWITCH_SLOT[1] / 2, -BIG / 2]) cube([SWITCH_SLOT[0], SWITCH_SLOT[1], BIG]);
for (m = [-1, 1]) translate([m * SWITCH_PITCH / 2, 0, -BIG / 2]) cylinder(d = SWITCH_HOLE_D, h = BIG);
}
// inserts
for (s = SCREWS) translate([s[0], s[1], Z_SPLIT - 1]) cylinder(d = INSERT_D, h = 1 + INSERT_L);
translate([0, 0, -ENGRAVE_D]) lx(1 + ENGRAVE_D) top_inlay_2d(); // ON/OFF and honeycomb inlays
for (m = [-1, 1]) translate([HOOK_POS[0] + m * HOOK_INSERTS, HOOK_POS[1], -PLATE - 7]) {
cylinder(d = INSERT_D, h = 7 + PLATE - 1);
cylinder(d = SCREW_D, h = BIG);
}
}
// ON/OFF text, cut into the top face and printed as a second-colour inlay
// (PART = "inlay", exported in the same frame as PART = "top").
module switch_text_2d() for (t = [["ON", -1], ["OFF", 1]]) translate([t[1] * 19, 0])
text(t[0], size = 5, halign = "center", valign = "center", font = "Liberation Sans:style=Bold");
// Honeycomb on the right of a diagonal through the middle of the top face.
// Only whole cells are drawn (every wall full width): a cell is kept when its
// outer edge lies right of the diagonal, inside the top face (EDGE_KEEP from
// the outline) and clear of the display window, the stick covers, the strap
// eyelet (with its travel) and the switch with its ON/OFF text.
HEX_R = 4.5; // cell circumradius (wall centre lines)
HEX_LINE = 1.2; // wall width (3 extrusion widths)
DIAG_POINT = [0, -14]; // the diagonal passes through here...
DIAG_ANGLE = 20; // ...leaning this far from the v axis (top end to the right)
EDGE_KEEP = 3; // from the outline (clear of the top chamfer)
HEX_GAP = 1.5; // around the keep-outs
HEX_OUT = (HEX_R + HEX_LINE / 2 / cos(30)); // outer circumradius of a cell
// The outline is the hull of rounded boxes with one corner radius, so it is
// this convex polygon grown by CORNER_R (corners listed counter-clockwise).
function _ol_pts() = let(r = CORNER_R, f = FRONT_BAND, b = REAR_BAND,
su = STICKS[1][0] + STICK_SQ[0] - r, sv = STICK_SQ[1] - r)
[[f[0][0] + r, f[1][1] - r], [-su, sv], [-su, -sv], [b[0][0] + r, b[0][1] + r],
[b[1][0] - r, b[0][1] + r], [su, -sv], [su, sv], [f[1][0] - r, f[1][1] - r]];
function _cross(a, b, q) = (b[0] - a[0]) * (q[1] - a[1]) - (b[1] - a[1]) * (q[0] - a[0]);
function _seg_dist(a, b, q) = let(d = b - a, t = max(0, min(1, ((q - a) * d) / (d * d)))) norm(q - (a + t * d));
function _poly_dist(P, q) = let(n = len(P),
inside = min([for (i = [0 : n - 1]) _cross(P[i], P[(i + 1) % n], q)]) >= 0)
inside ? 0 : min([for (i = [0 : n - 1]) _seg_dist(P[i], P[(i + 1) % n], q)]);
function _in_face(q) = _poly_dist(_ol_pts(), q) <= CORNER_R - EDGE_KEEP;
function _right(q) = ((q - DIAG_POINT) * [cos(DIAG_ANGLE), -sin(DIAG_ANGLE)]) >= 0;
function _rect_dist(c, size, q) = let(d = [max(abs(q[0] - c[0]) - size[0] / 2, 0), max(abs(q[1] - c[1]) - size[1] / 2, 0)]) norm(d);
function _clear(q) = let(rr = HEX_OUT + HEX_GAP)
_rect_dist(NX_WIN, NX_WINDOW + [2, 2] * NX_BEZEL, q) >= rr &&
min([for (st = STICKS) norm(q - st)]) >= 53.5 / 2 + rr &&
_rect_dist(HOOK_POS, [HOOK_BASE[0], HOOK_BASE[1] + 2 * HOOK_TRAVEL], q) >= rr &&
_rect_dist(SWITCH_POS, [2 * 19 + 16, 7], q) >= rr;
function _cell_ok(c) = _clear(c) && min([for (k = [0 : 5]) let(q = c + HEX_OUT * [cos(60 * k), sin(60 * k)])
(_right(q) && _in_face(q)) ? 1 : 0]) == 1;
HEX_CELLS = [for (i = [-30 : 30], j = [-20 : 20])
let(c = [i * 1.5 * HEX_R, (j + (i % 2 == 0 ? 0 : 0.5)) * sqrt(3) * HEX_R]) if (_cell_ok(c)) c];
// drop stray cells (fewer than 2 neighbours)
HEX_KEEP = [for (c = HEX_CELLS) if (len([for (o = HEX_CELLS) if (o != c && norm(o - c) < 2 * HEX_R) 1]) >= 2) c];
module hex_pattern_2d() for (c = HEX_KEEP) translate(c) difference() {
circle(r = HEX_OUT, $fn = 6);
circle(r = HEX_R - HEX_LINE / 2 / cos(30), $fn = 6);
}
module top_inlay_2d() { translate(SWITCH_POS) switch_text_2d(); hex_pattern_2d(); }
// Two inlays, so each can have its own colour (owner: black case, red
// honeycomb, white ON/OFF). Each extra colour adds a swap on the first 3 layers.
module hex_inlay() translate([0, 0, -ENGRAVE_D]) lx(ENGRAVE_D) hex_pattern_2d();
module text_inlay() translate([0, 0, -ENGRAVE_D]) lx(ENGRAVE_D) translate(SWITCH_POS) switch_text_2d();
// ---------- bottom shell ----------------------------------------------------
USBC_V = FRONT_V - 0.6; // receptacle front, 0.6 inside the front face
module bottom_shell() render(convexity = 10) difference() {
union() {
difference() {
intersection() {
outer_solid();
translate([-BIG / 2, -BIG / 2, Z_BOT - 1]) cube([BIG, BIG, Z_SPLIT - Z_BOT + 1]);
}
inner_solid();
}
// locating lip
translate([0, 0, Z_SPLIT - 3]) lx(3 + LIP_H) difference() {
offset(delta = -(T + FIT)) outline_2d();
offset(delta = -(T + FIT + LIP_W)) outline_2d();
for (s = SCREWS) translate(s) circle(d = BOSS_D + 2 * FIT);
}
// ties the lip to the wall; its underside steps out at 45 deg (no flat overhang)
for (i = [0 : 4]) translate([0, 0, Z_SPLIT - 3 - i * 0.35]) lx(3 + 0.01) difference() {
offset(delta = -(T - JOIN)) outline_2d();
offset(delta = -(T + FIT + LIP_W - i * 0.35)) outline_2d();
for (s = SCREWS) translate(s) circle(d = BOSS_D + 2 * FIT);
}
intersection() {
inner_solid();
union() {
// screw towers
for (s = SCREWS) translate([s[0], s[1], Z_BOT]) cylinder(d = BOSS_D, h = Z_SPLIT - Z_BOT);
// bail pivot bosses in the side walls, on pillars down to the floor (printable)
for (m = [-1, 1]) hull() for (z = [BAIL_PIVOT[1], Z_BOT + 5])
translate([m * SIDE_U, BAIL_PIVOT[0], z]) rotate([0, -m * 90, 0]) cylinder(d = 10, h = 14);
// UPS standoffs
for (m = [-1, 1]) translate([UPS_CENTRE[0] + m * UPS_HOLES, UPS_CENTRE[1], Z_BOT]) cylinder(d = 6, h = UPS_Z - Z_BOT);
// kickstand recess and hinge trough walls
kickstand_housing();
// USB-C cradle
usbc_cradle();
}
}
// main board standoffs
intersection() {
inner_solid();
perf_clamp_place() translate([0, 0, Z_BOT - PERF_Z]) cylinder(d = 8, h = PERF_Z - Z_BOT);
}
// front eyelet inserts: bosses behind the front wall
intersection() {
inner_solid();
for (m = [-1, 1]) translate([m * HOOK_INSERTS, FRONT_V - T - 6 + JOIN, HOOK_FRONT_Z]) rotate([-90, 0, 0]) cylinder(d = 8, h = 6 + JOIN);
}
}
// screw holes: counterbore from below, clearance up to the split
for (s = SCREWS) translate([s[0], s[1], 0]) {
translate([0, 0, Z_BOT - 1]) cylinder(d = HEAD_D, h = HEAD_Z - Z_BOT + 1);
cylinder(d = SCREW_D, h = BIG, center = true);
}
for (m = [-1, 1]) translate([UPS_CENTRE[0] + m * UPS_HOLES, UPS_CENTRE[1], Z_BOT + 1.2]) cylinder(d = 2.5, h = 20);
for (l = UPS_LEDS) translate(concat(UPS_CENTRE + l, Z_BOT - 1)) lx(T + 2) hull() for (d = [-2, 2]) translate([0, d]) circle(d = 2);
perf_clamp_place() translate([0, 0, -6]) cylinder(d = INSERT_D, h = 7);
for (m = [-1, 1]) translate([m * HOOK_INSERTS, FRONT_V - INSERT_L - 1, HOOK_FRONT_Z]) rotate([-90, 0, 0]) cylinder(d = INSERT_D, h = INSERT_L + 2);
kickstand_cut();
usbc_cut();
for (m = [-1, 1]) translate([m * SIDE_U, BAIL_PIVOT[0], BAIL_PIVOT[1]]) rotate([0, -m * 90, 0]) translate([0, 0, -1]) cylinder(d = INSERT_D, h = 1 + 8);
}
// Kickstand: a flap in a recess in the underside, hinged at the front on a
// pin through a barrel. Friction on the pin holds the angle.
KS_RECESS = KS_T + 0.5;
KS_ROOF = Z_BOT + KS_RECESS + 2; // top of the recess roof
KS_AXIS_Z = Z_BOT + KS_BARREL_D / 2; // barrel tangent to the underside (sits on the bed when printed)
module kickstand_housing() {
translate([-KS_W / 2 - FIT - KS_WALL, KS_V[0] - FIT - KS_WALL_V, Z_BOT])
cube([KS_W + 2 * (FIT + KS_WALL), KS_V[1] - KS_V[0] + KS_BARREL_D / 2 + 2 * FIT + 2 * KS_WALL_V, KS_RECESS + 2]);
translate([-KS_W / 2 - FIT - KS_WALL, KS_V[1] - KS_BARREL_D / 2 - FIT - KS_WALL_V, Z_BOT])
cube([KS_W + 2 * (FIT + KS_WALL), KS_BARREL_D + 2 * (FIT + KS_WALL_V), KS_BARREL_D + 0.6 + FIT + 2]);
}
module kickstand_cut() {
translate([-KS_W / 2 - FIT, KS_V[0] - FIT, Z_BOT - 1]) cube([KS_W + 2 * FIT, KS_V[1] - KS_V[0] + 2 * FIT, 1 + KS_RECESS]);
translate([-KS_W / 2 - FIT, KS_V[1] - KS_BARREL_D / 2 - FIT, Z_BOT - 1]) cube([KS_W + 2 * FIT, KS_BARREL_D + 2 * FIT, 1 + KS_BARREL_D + 0.6 + FIT]);
translate([0, KS_V[1], KS_AXIS_Z]) rotate([0, 90, 0]) cylinder(d = KS_PIN_D, h = KS_W + 2 * KS_WALL + 10, center = true);
translate([KS_W / 2 + FIT + KS_WALL - 2.5, KS_V[1], KS_AXIS_Z]) rotate([0, 90, 0]) rotate([0, 0, 30]) cylinder(d = 5.5 / cos(30) + 0.3, h = 5, $fn = 6);
}
module kickstand() render(convexity = 10) difference() {
union() {
hull() {
translate([-KS_W / 2, KS_V[0], Z_BOT]) cube([KS_W, 1, KS_T]);
translate([-KS_W / 2, KS_V[1] - 1, Z_BOT]) cube([KS_W, 1, KS_T]);
}
translate([0, KS_V[1], KS_AXIS_Z]) rotate([0, 90, 0]) cylinder(d = KS_BARREL_D, h = KS_W, center = true);
// finger notch lip at the free end is cut below
}
translate([0, KS_V[1], KS_AXIS_Z]) rotate([0, 90, 0]) cylinder(d = KS_PIN_D, h = KS_W + 2, center = true);
translate([0, KS_V[0] - 2, Z_BOT - 1]) scale([1, 0.6, 1]) cylinder(r = 9, h = KS_T + 2); // finger notch
}
module perf_place() translate(concat(PERF_POS, PERF_Z)) rotate([0, 0, -90]) children();
// at each clamp post's axis, Z = 0 on the board's underside
module perf_clamp_place() perf_place() for (c = PERF_CLAMPS)
translate([c[0] + (c[0] > PERF[0] / 2 ? 1 : -1) * PERF_CLAMP_OUT, c[1], 0]) children();
module perf_clamp_screws() perf_clamp_place() translate([0, 0, PERF[2]]) color("#b0b0b0") {
cylinder(d = 7, h = 0.5); // washer
translate([0, 0, 0.5]) cylinder(d = 5.7, h = 1.65); // M3 button head
}
// USB-C breakout on a block, the receptacle in a slot through the front wall.
module usbc_cradle() translate([USBC_POS[0] - USBC_BOARD[0] / 2 - 2, USBC_V - USBC_BOARD[1] - 2, Z_BOT])
cube([USBC_BOARD[0] + 4, USBC_BOARD[1] + 2 + 3, USBC_Z - Z_BOT]);
module usbc_cut() {
inner_v = FRONT_V - T;
// board pocket (glue it in), open towards the inside; through the wall only the board's own slot
translate([USBC_POS[0] - USBC_BOARD[0] / 2 - FIT, USBC_V - USBC_BOARD[1] - FIT, USBC_Z]) cube([USBC_BOARD[0] + 2 * FIT, inner_v - (USBC_V - USBC_BOARD[1] - FIT), 20]);
translate([USBC_POS[0] - USBC_BOARD[0] / 2 - FIT, USBC_V - 5, USBC_Z]) cube([USBC_BOARD[0] + 2 * FIT, 5 + FIT, USBC_BOARD[2] + 2 * FIT]);
// receptacle opening, chamfered on the outside for the plug
translate([USBC_POS[0], USBC_V - 3, USBC_Z + USBC_BOARD[2] + USBC_RCPT[2] / 2]) rotate([-90, 0, 0]) {
linear_extrude(10) offset(r = 1.4) square([USBC_RCPT[0] + 0.6 - 2.8, USBC_RCPT[2] + 0.6 - 2.8], center = true);
translate([0, 0, 3 + 0.6 - 0.01]) linear_extrude(1.01, scale = [1.3, 1.6]) offset(r = 1.4) square([USBC_RCPT[0] + 0.6 - 2.8, USBC_RCPT[2] + 0.6 - 2.8], center = true);
}
}
// Strap eyelet: printed base down (the d8 loop hole is a short bridge).
module eyelet() render(convexity = 10) difference() {
b = HOOK_BASE;
union() {
translate([-b[0] / 2, -b[1] / 2, 0]) cube(b);
hull() {
translate([-4, -b[1] / 2 + 2, 0]) cube([8, b[1] - 4, b[2]]);
translate([-4, 0, HOOK_H - b[1] / 2 + 2]) rotate([0, 90, 0]) cylinder(r = b[1] / 2 - 2, h = 8);
}
}
translate([-10, 0, HOOK_H - b[1] / 2 + 2]) rotate([0, 90, 0]) cylinder(d = HOOK_HOLE_D, h = 20);
for (m = [-1, 1]) translate([m * HOOK_INSERTS, 0, -1]) hull() for (d = [-1, 1]) translate([0, d * HOOK_TRAVEL, 0]) cylinder(d = SCREW_D, h = 10);
// screw heads (M3 button head, 5.7 mm) in slotted counterbores beside the loop
for (m = [-1, 1]) translate([m * HOOK_INSERTS, 0, 2]) hull() for (d = [-1, 1]) translate([0, d * HOOK_TRAVEL, 0]) cylinder(d = 6.2, h = 10);
}
module eyelet_placed(shift = 0) translate([HOOK_POS[0], HOOK_POS[1] + shift, 0]) eyelet();
module eyelet_front_placed() translate([HOOK_POS[0], FRONT_V, HOOK_FRONT_Z]) rotate([-90, 0, 0]) eyelet();
// Brace bail, in its pivot frame: arms along +y (folded forward), pivots on x.
BAIL_X = SIDE_U + BAIL_GAP;
module bail() render(convexity = 10) difference() {
union() {
for (m = [-1, 1]) hull() for (y = [0, BAIL_L]) translate([m > 0 ? BAIL_X : -BAIL_X - BAIL_T, y, 0]) rotate([0, 90, 0]) cylinder(d = BAIL_H, h = BAIL_T);
// crossbar, bowed outwards
n = 16;
w = BAIL_X + BAIL_T / 2;
translate([0, 0, -BAIL_H / 2]) lx(BAIL_H) for (i = [0 : n - 1]) hull() for (k = [i, i + 1]) {
x = -w + k * 2 * w / n;
translate([x, BAIL_L + BAIL_BOW * (1 - pow(x / w, 2))]) circle(d = 8);
}
}
rotate([0, 90, 0]) cylinder(d = SCREW_D, h = 2 * BIG, center = true);
}
module bail_placed() translate([0, BAIL_PIVOT[0], BAIL_PIVOT[1]]) rotate([BAIL_ANGLE, 0, 0]) bail();
// ---------- reference parts (local frames, then placed) ---------------------
module nextion() {
translate(concat(NX_CENTRE, NX_BOARD_TOP - 1.6)) color("#1e5a2a") difference() {
translate(concat(-NX_BOARD / 2, 0)) cube(concat(NX_BOARD, 1.6));
for (du = [-1, 1], dv = [-1, 1]) translate([du * NX_HOLES[0], dv * NX_HOLES[1], 0] / 2 + [0, 0, -1]) cylinder(d = 3.2, h = 4);
}
translate(concat(NX_WIN - NX_LCD / 2, NX_BOARD_TOP)) color("#202020") cube(concat(NX_LCD, NX_LCD_T));
translate(concat(NX_WIN - [73.44, 48.96] / 2, -NX_BEZEL - 0.2)) color("#3050a0") cube([73.44, 48.96, 0.2]);
translate(concat(NX_CENTRE + [(NX_FLIP ? 1 : -1) * (NX_BOARD[0] / 2 - 7), -5], NX_BOARD_TOP - 1.6 - 6)) color("#eee") cube([6, 10, 6]); // J1 4-pin connector (approx.)
}
module ups_18650() translate(concat(UPS_CENTRE, UPS_Z)) {
color("#202020") difference() {
translate([-89 / 2, -22 / 2, 0]) cube([89, 22, 1.6]);
for (m = [-1, 1]) translate([m * UPS_HOLES, 0, -1]) cylinder(d = 3, h = 4);
}
color("#151515") translate([-77 / 2, -21 / 2, 1.6]) difference() {
cube([77, 21, 22.4 - 1.6]);
translate([3, 1.5, 3]) cube([71, 18, 30]);
}
color("#4060c0") translate([-65 / 2, 0, 1.6 + 3 + 18.5 / 2]) rotate([0, 90, 0]) cylinder(d = 18.5, h = 65);
color("#b0b0b0") translate([89 / 2 - 7, -4.5, 1.6]) cube([7.5, 9, 3.2]); // Type-C (charge input)
color("#808080") translate([89 / 2 + 0.5, -6, 0]) cube([18, 12, 7]); // cut-cable plug (approx.)
}
// Main board as in the owner's photos (layout approximate).
module main_board() { perf_clamp_screws(); main_board_only(); }
module main_board_only() perf_place() {
color("#2a8a4a") difference() {
cube(PERF);
}
// Teensy 4.0 in female headers (8.5 mm), micro-USB at the board edge
translate([12.1, 1, PERF[2]]) {
color("#111") for (x = [0, 17.8 - 2.5]) translate([x, 0, 0]) cube([2.5, 35.6, 8.5]);
translate([0, 0, 8.5]) {
color("#1e5a2a") cube([17.8, 35.6, 1.6]);
color("#222") translate([4, 12, 1.6]) cube([10, 10, 1.2]);
color("#c0c0c0") translate([(17.8 - 7.5) / 2, -1, 1.6]) cube([7.5, 5.7, 2.9]);
color("#808080") translate([(17.8 - 10) / 2, -1 - 18, 1.6 - 2]) cube([10, 18, 7]); // cable plug (approx.)
}
}
// nRF24L01 lying over the far edge, on its 2 x 4 header
translate([15, 63, PERF[2]]) {
color("#111") translate([2, 0, 0]) cube([10, 5, 2.5]);
color("#151515") translate([0, 0, 2.5]) cube([15.3, 29, 1.2]);
}
color("#222") translate([2, 74, PERF[2]]) cube([11, 6.3, 6.3]); // 100 uF cap, lying
color("#222") translate([5, 58, PERF[2]]) cube([7, 6.5, 1.8]); // AMS1117
// ribbon and display/IMU connectors at the edge, plugs on top (approx.)
color("#333") translate([44, 8, PERF[2]]) cube([5, 21, 12]);
color("#333") translate([44, 44, PERF[2]]) cube([5, 11, 12]);
}
// GY-521 on the main board, on headers (board frame: 15.6 across, 21.2 along)
module imu_gy521() perf_place() translate(concat(PERF_IMU, PERF[2])) {
color("#111") translate([0, 1, 0]) cube([2.5, 19, 8.5]);
translate([0, 0, 8.5]) {
color("#1f4fa0") cube([15.6, 21.2, 1.6]);
color("#222") translate([6, 8.6, 1.6]) cube([4, 4, 1]);
}
}
module usbc_breakout() translate([USBC_POS[0], USBC_V, USBC_Z]) {
color("#1a7a3a") translate([-USBC_BOARD[0] / 2, -USBC_BOARD[1], 0]) cube(USBC_BOARD);
color("#c0c0c0") translate([-USBC_RCPT[0] / 2, -USBC_RCPT[1], USBC_BOARD[2]]) cube(USBC_RCPT);
}
// Slide switch as on the old remote: mounting plate on the top face, screwed
// down with 2 screws, body hanging through the slot. Sizes approximate.
module slide_switch() translate(SWITCH_POS) color("#303030") {
translate([-12.5, -3.5, 0]) cube([25, 7, 0.8]); // mounting plate
translate([-7.5, -3.5, -10]) cube([15, 7, 10]); // body, through the slot
translate([-1.5, -1.5, 0.8]) cube([3, 3, 4]); // knob
}
// JH-D300X-R1 3-axis joystick (owner's drawing): handle d35 with the twist
// pot inside, dust cover d53.5 on top of the plate, 40.4 mm control box
// (25.5 tall) under it, clamping the plate with 4 x M2.5 x 14. X/Y pots
// d16.5 sticking 9.2 out of the box on -x and -y. Local Z = 0 on the cover's
// underside (the top face); the box hangs from the plate's underside.
JOY_BOX = 40.4; JOY_BOX_H = 25.5; JOY_POT_D = 16.5; JOY_POT_L = 49.6 - 40.4;
JOY_COVER_T = 3.8; JOY_POT_Z = 15.3; // pot axis above the box bottom (from the drawing)
module jh_d300x() {
zb = -PLATE - JOY_BOX_H; // box bottom
color("#202020") {
difference() {
cylinder(d1 = 53.5, d2 = 50, h = JOY_COVER_T);
for (du = [-1, 1], dv = [-1, 1]) translate([du * STICK_SCREW, dv * STICK_SCREW, -1]) cylinder(d = 2.7, h = 6);
}
translate([0, 0, JOY_COVER_T]) cylinder(d = 39.5, h = 1); // dust ring
translate([-JOY_BOX / 2, -JOY_BOX / 2, zb]) cube([JOY_BOX, JOY_BOX, JOY_BOX_H]);
translate([0, 0, zb + JOY_POT_Z]) {
rotate([0, -90, 0]) translate([0, 0, JOY_BOX / 2]) cylinder(d = JOY_POT_D, h = JOY_POT_L); // Y pot, -x
rotate([90, 0, 0]) translate([0, 0, JOY_BOX / 2]) cylinder(d = JOY_POT_D, h = JOY_POT_L); // X pot, -y
}
t = JOY_COVER_T;
translate([0, 0, t]) cylinder(d = 6, h = 11.5); // shaft
translate([0, 0, t + 11]) cylinder(d1 = 12, d2 = 18, h = 8); // neck
translate([0, 0, t + 19]) cylinder(d = 32, h = 7);
translate([0, 0, t + 26]) cylinder(d = 35, h = 19); // knurled grip
translate([0, 0, t + 45]) cylinder(d1 = 35, d2 = 30, h = 8); // top: 53 above the cover
}
}
// pots towards the middle and towards the user
module sticks() for (s = STICKS) translate(concat(s, 0)) if (s[0] > 0) jh_d300x(); else mirror([1, 0, 0]) jh_d300x();
module electronics() {
nextion();
ups_18650();
main_board();
imu_gy521();
usbc_breakout();
slide_switch();
}
// ---------- assembly and print layout --------------------------------------
module kickstand_placed() translate([0, KS_V[1], KS_AXIS_Z]) rotate([KS_OPEN, 0, 0]) translate([0, -KS_V[1], -KS_AXIS_Z]) kickstand();
module remote_v2() {
if (SHOW_BOTTOM) { color("#1c1c1c") bottom_shell(); color("#1c1c1c") kickstand_placed(); color("#1c1c1c") bail_placed(); }
if (HOOK_MOUNT == "front") color("#1c1c1c") eyelet_front_placed();
else if (SHOW_TOP) translate([0, 0, EXPLODE]) color("#1c1c1c") eyelet_placed();
if (SHOW_TOP) translate([0, 0, EXPLODE]) { color("#262626") top_shell(); color("#c8102e") hex_inlay(); color("#f2f2f2") text_inlay(); }
if (SHOW_PARTS) { translate([0, 0, EXPLODE]) { nextion(); slide_switch(); }
ups_18650(); main_board(); imu_gy521(); usbc_breakout(); }
if (SHOW_STICKS) translate([0, 0, EXPLODE]) sticks();
}
if (PART == "assembly") remote_v2();
else if (PART == "top") rotate([180, 0, 0]) top_shell(); // face down on the bed
else if (PART == "inlay") rotate([180, 0, 0]) hex_inlay(); // load with "top" (and "text") as one multi-part object
else if (PART == "text") rotate([180, 0, 0]) text_inlay();
else if (PART == "bottom") translate([0, 0, -Z_BOT]) bottom_shell();
else if (PART == "kickstand") translate([0, 0, -Z_BOT]) kickstand();
else if (PART == "eyelet") eyelet(); // base on the bed, the loop hole bridges
else if (PART == "bail") translate([0, 0, BAIL_H / 2]) bail();
Binary file not shown.
Binary file not shown.
+2 -2
View File
@@ -1,6 +1,6 @@
; Hexapod: two firmware images in one project.
; pio run -e robot build robot/ (Teensy 3.6)
; pio run -e remote build remote/ (Teensy 4.1)
; pio run -e remote build remote/ (Teensy 4.0)
; pio run -e robot -t upload flash (Teensy Loader / teensy_cli)
; pio device monitor -e robot serial monitor at 115200
;
@@ -25,5 +25,5 @@ board = teensy36
custom_src_dir = robot
[env:remote]
board = teensy41
board = teensy40
custom_src_dir = remote
+5 -3
View File
@@ -2,7 +2,7 @@
#include <Arduino.h>
// =====================================================================
// Remote handset config (Teensy 4.1). Everything here is a placeholder
// Remote handset config (Teensy 4.0). Everything here is a placeholder
// until checked against your real wiring and parts - see the BENCH notes.
// Radio address/channel/rate/PA/payload size are NOT here: they live in
// shared/HexapodProtocol so they can't drift from the robot.
@@ -69,8 +69,10 @@ constexpr float STICK_EXPO[NUM_AXES] = { 0.25f, 0.25f, 0.30f, 0.20f, 0.20f,
// One-pole low-pass on raw ADC counts (1 = no filtering). Pots are noisy.
constexpr float STICK_FILTER_ALPHA = 0.5f;
// ---- Remote IMU: MPU6050 on the second I2C bus (Wire2: SDA2 = 25, SCL2 = 24) ----
// Not Wire (18/19): those pins are stick axes A4/A5.
// ---- Remote IMU: MPU6050 on the third I2C bus (Wire2: SDA2 = 25, SCL2 = 24) ----
// On the Teensy 4.0, 24/25 are solder pads on the underside, not edge pins.
// Not Wire (18/19): those pins are stick axes A4/A5. Not Wire1 (17/16) either:
// those are stick axes A3/A2.
#define IMU_WIRE Wire2
constexpr uint8_t IMU_ADDR = 0x68; // 0x69 if AD0 is pulled high
// Mounting remap: which chip axis (0=X,1=Y,2=Z) and sign gives each handset
+22 -4
View File
@@ -1,4 +1,4 @@
# Hexapod remote firmware (Teensy 4.1)
# Hexapod remote firmware (Teensy 4.0)
Handheld transmitter for the hexapod. It reads two 3-axis twist-grip
joysticks and an MPU6050, takes operator commands from a Nextion
@@ -6,6 +6,24 @@ touchscreen, and sends a `CmdPacket` (defined in
`../shared/HexapodProtocol/HexapodProtocol.h`) to the robot over nRF24L01
at 100 Hz.
## Planned
- **Battery level** (not built yet): read the 18650's voltage through a
~100k/100k divider from the cell's + (not the boost board's 5 V output)
into A6 (pin 20, free), with 100 nF to GND, and show the charge on the
Nextion with a low-battery warning. Details in
`../hardware/openscad/PLANNING.md` (notes for future designs).
- **IMU on the normal pin headers** (suggestion, not done): with the GY-521 on
the main board, wire it to Wire (SDA 18 / SCL 19) instead of Wire2 (the
24/25 pads under the Teensy 4.0). 18/19 are A4/A5, used by two stick axes
now, so move those two axes to A7 (pin 21) and A8 (pin 22): all on the
edge headers. A6 (pin 20) stays free for the battery divider, A9 (23) is
spare. Firmware: in `Config.h` `STICK_PINS = { A0, A1, A2, A3, A7, A8 }`
and `#define IMU_WIRE Wire`; `Sticks.cpp` reads through `STICK_PINS`, so
nothing else changes. Redo the stick axis check (`p` dump) and calibration
afterwards. (Wire1 is no way out: its 16/17 are stick pins A2/A3 too.)
## Building
From the `2026-current` folder: `pio run -e remote`, flash with
@@ -13,17 +31,17 @@ From the `2026-current` folder: `pio run -e remote`, flash with
## Wiring (from the old remote sketch in `../../2019-teensy-nrf24/remote/`; edit `Config.h` if yours differs)
| Part | Signal | Teensy 4.1 pin |
| Part | Signal | Teensy 4.0 pin |
|------|--------|----------------|
| nRF24L01 | MOSI / MISO / SCK | 11 / 12 / 13 (SPI0) |
| nRF24L01 | CE / CSN | 9 / 10 |
| nRF24L01 | VCC | 3.3 V, with a 10–100 µF cap right at the module |
| MPU6050 | SDA / SCL | **25 / 24 (Wire2)**: not 18/19, those are stick pins A4/A5 |
| MPU6050 | SDA / SCL | **25 / 24 (Wire2)**, solder pads on the underside of the 4.0: not 18/19, those are stick pins A4/A5 |
| Nextion | TX → RX1, RX ← TX1 | 0 / 1 (Serial1), 5 V supply |
| Sticks | 6 axes | A0–A5. Which axis is on which pin isn't known yet: reorder `STICK_PINS` until the `p` dump reads right |
**MPU6050 rewiring:** the old remote had its MPU code switched off, probably
because A4/A5 double as Wire's pins. Move the MPU's SDA/SCL to pins 25/24.
because A4/A5 double as Wire's pins. Move the MPU's SDA/SCL to pins 25/24 (the pads under the board).
Stick pots are wired 3.3 V – wiper – GND. **Never feed 5 V into a Teensy
4.x analog pin.**
+1 -1
View File
@@ -7,7 +7,7 @@
#include "NextionUI.h"
#include "SerialConsole.h"
// Hexapod remote (Teensy 4.1): reads two 3-axis sticks and the handset
// Hexapod remote (Teensy 4.0): reads two 3-axis sticks and the handset
// MPU6050, takes operator commands from the Nextion touchscreen (and the USB
// serial console), and transmits a CmdPacket to the robot at TX_HZ.
// See README.md for wiring, calibration and the serial key map.
+1 -1
View File
@@ -17,7 +17,7 @@ named after the year it started, with its firmware, simulation, hardware, docume
| [`2016-ssc32-processing-port/`](2016-ssc32-processing-port/) | ~2016–2018 | Arduino + SSC-32 | the Processing simulator's classes ported to Arduino, driving the SSC-32 again |
| [`2018-unity-sim/`](2018-unity-sim/) | 2018–2023 | PC + SSC-32, later the Teensy | Unity computes the walking and drives the robot: first the SSC-32 over serial, from 2019 through the remote |
| [`2019-teensy-nrf24/`](2019-teensy-nrf24/) | 2019–2022 | Teensy 3.6 on the robot (replaces the SSC-32), Teensy remote with Nextion screen, nRF24L01 | servo passthrough: Unity → remote over USB → radio → robot |
| [`2026-current/`](2026-current/) | 2026– | Teensy 3.6 robot, Teensy 4.1 remote, Fusion 360 designed parts | IK, gait, body pose and IMU stabilisation on the robot; the unchanged firmware also runs inside Unity |
| [`2026-current/`](2026-current/) | 2026– | Teensy 3.6 robot, Teensy 4.0 remote, Fusion 360 designed parts, OpenSCAD rebuild and new remote | IK, gait, body pose and IMU stabilisation on the robot; the unchanged firmware also runs inside Unity |
## Repository notes