2026 remote v2: printable bottom shell, notes for the PC radio link

- Bottom shell: the brace pivot bosses stand on pillars and the lip's tie
  band steps out at 45 deg (both were floating overhangs); the kickstand
  barrel sits on the bed. Checked by slicing the STLs layer by layer: only
  bridges are left. STLs re-exported.
- remote_v2_top_multicolor.3mf: now the owner's OrcaSlicer project (all
  parts on two plates); export_3mf.py regenerates the plain multi-part file.
- README "Planned": a USB nRF24 stick on the PC so Unity can talk to both
  the robot and the remote (what to work out), plus pointers to the other
  notes for later.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
mangavalkandClaude Opus 5.5 committed 2026-11-14 19:13:28 +01:00
1 parent 60605209fb
commit 80270ba17e
6 files changed
+44 -11

No files matched your search

+26
View File
@@ -75,6 +75,32 @@ Hardware (besides the electronics of the old remote):
Design notes, checks and open points: [hardware/openscad/PLANNING.md](hardware/openscad/PLANNING.md).
## Planned
- **PC radio link (owner, later):** a USB nRF24L01 stick on the PC (it
probably shows up as a serial port), on the same radio as the robot and the
remote, so Unity on the PC can both receive data from (telemetry) and send
data to the robot and the remote. Not designed yet. To work out:
- what the stick's firmware does: many of these sticks are a USB-serial
chip with a microcontroller set up by AT commands (address, channel, data
rate) that passes raw payloads through; check that it can match
`HXP_RADIO_*` in `shared/HexapodProtocol/HexapodProtocol.h` (channel 96,
250 kbps, 5-byte address `HXPD1`, fixed payload of `sizeof(CmdPacket)`)
and whether it can do auto-ack and ack payloads;
- the radio protocol: today the remote only transmits a `CmdPacket` to the
robot and nothing comes back. Three nodes need an address per node (or
per pipe), a packet type byte, and telemetry back (e.g. as ack payloads
or in time slots) so the nodes don't talk over each other; who has
priority when the PC and the remote both send commands;
- Unity side: a serial-port reader/writer next to the simulation (the
2019 generation already drove the robot from Unity, through the remote
over USB: see `../2019-teensy-nrf24/`).
- Remote battery level and the IMU on the normal pin headers: see
[remote/README.md](remote/README.md), "Planned".
- Robot power: a stable 6 V supply for the 18 servos, see
[hardware/openscad/PLANNING.md](hardware/openscad/PLANNING.md), "Notes for
future designs".
## Where to go next
- **[robot/README.md](robot/README.md)**: placeholder geometry to measure,
@@ -189,6 +189,11 @@ charge/on LEDs show through two slots in the floor.
cells dropped. Colours (owner, ASA): black case, red honeycomb (PART
"inlay"), white ON/OFF (PART "text"); load "top", "inlay" and "text" as one
multi-part object. Each extra colour adds a swap on the first 3 layers only.
- Printability (the STLs sliced in 0.2 mm layers, every area not carried by
the layer below listed): the brace pivot bosses stand on pillars and the
lip's tie band steps out at 45 deg (both were floating overhangs in the
first export); what's left are bridges: the 30 mm kickstand-recess roof,
the hinge trough, hole and counterbore tops, the USB-C opening.
- Checked: no part collides with the shells or with each other, the shells
and the inlay don't overlap, kickstand clear at 0 and 70 deg, bail clear
from 0 to -180 deg (CGAL intersections).
@@ -307,9 +307,10 @@ module bottom_shell() render(convexity = 10) difference() {
offset(delta = -(T + FIT + LIP_W)) outline_2d();
for (s = SCREWS) translate(s) circle(d = BOSS_D + 2 * FIT);
}
translate([0, 0, Z_SPLIT - 3]) lx(3) difference() { // ties the lip to the wall
// ties the lip to the wall; its underside steps out at 45 deg (no flat overhang)
for (i = [0 : 4]) translate([0, 0, Z_SPLIT - 3 - i * 0.35]) lx(3 + 0.01) difference() {
offset(delta = -(T - JOIN)) outline_2d();
offset(delta = -(T + FIT + LIP_W)) outline_2d();
offset(delta = -(T + FIT + LIP_W - i * 0.35)) outline_2d();
for (s = SCREWS) translate(s) circle(d = BOSS_D + 2 * FIT);
}
intersection() {
@@ -317,8 +318,9 @@ module bottom_shell() render(convexity = 10) difference() {
union() {
// screw towers
for (s = SCREWS) translate([s[0], s[1], Z_BOT]) cylinder(d = BOSS_D, h = Z_SPLIT - Z_BOT);
// bail pivot bosses in the side walls
for (m = [-1, 1]) translate([m * SIDE_U, BAIL_PIVOT[0], BAIL_PIVOT[1]]) rotate([0, -m * 90, 0]) cylinder(d = 10, h = 14);
// bail pivot bosses in the side walls, on pillars down to the floor (printable)
for (m = [-1, 1]) hull() for (z = [BAIL_PIVOT[1], Z_BOT + 5])
translate([m * SIDE_U, BAIL_PIVOT[0], z]) rotate([0, -m * 90, 0]) cylinder(d = 10, h = 14);
// UPS standoffs
for (m = [-1, 1]) translate([UPS_CENTRE[0] + m * UPS_HOLES, UPS_CENTRE[1], Z_BOT]) cylinder(d = 6, h = UPS_Z - Z_BOT);
// kickstand recess and hinge trough walls
@@ -356,7 +358,7 @@ module bottom_shell() render(convexity = 10) difference() {
// pin through a barrel. Friction on the pin holds the angle.
KS_RECESS = KS_T + 0.5;
KS_ROOF = Z_BOT + KS_RECESS + 2; // top of the recess roof
KS_AXIS_Z = Z_BOT + KS_BARREL_D / 2 + 0.3;
KS_AXIS_Z = Z_BOT + KS_BARREL_D / 2; // barrel tangent to the underside (sits on the bed when printed)
module kickstand_housing() {
translate([-KS_W / 2 - FIT - KS_WALL, KS_V[0] - FIT - KS_WALL_V, Z_BOT])
cube([KS_W + 2 * (FIT + KS_WALL), KS_V[1] - KS_V[0] + KS_BARREL_D / 2 + 2 * FIT + 2 * KS_WALL_V, KS_RECESS + 2]);