diff --git a/2026-current/README.md b/2026-current/README.md index 4122359..b6c7605 100644 --- a/2026-current/README.md +++ b/2026-current/README.md @@ -75,6 +75,32 @@ Hardware (besides the electronics of the old remote): Design notes, checks and open points: [hardware/openscad/PLANNING.md](hardware/openscad/PLANNING.md). +## Planned + +- **PC radio link (owner, later):** a USB nRF24L01 stick on the PC (it + probably shows up as a serial port), on the same radio as the robot and the + remote, so Unity on the PC can both receive data from (telemetry) and send + data to the robot and the remote. Not designed yet. To work out: + - what the stick's firmware does: many of these sticks are a USB-serial + chip with a microcontroller set up by AT commands (address, channel, data + rate) that passes raw payloads through; check that it can match + `HXP_RADIO_*` in `shared/HexapodProtocol/HexapodProtocol.h` (channel 96, + 250 kbps, 5-byte address `HXPD1`, fixed payload of `sizeof(CmdPacket)`) + and whether it can do auto-ack and ack payloads; + - the radio protocol: today the remote only transmits a `CmdPacket` to the + robot and nothing comes back. Three nodes need an address per node (or + per pipe), a packet type byte, and telemetry back (e.g. as ack payloads + or in time slots) so the nodes don't talk over each other; who has + priority when the PC and the remote both send commands; + - Unity side: a serial-port reader/writer next to the simulation (the + 2019 generation already drove the robot from Unity, through the remote + over USB: see `../2019-teensy-nrf24/`). +- Remote battery level and the IMU on the normal pin headers: see + [remote/README.md](remote/README.md), "Planned". +- Robot power: a stable 6 V supply for the 18 servos, see + [hardware/openscad/PLANNING.md](hardware/openscad/PLANNING.md), "Notes for + future designs". + ## Where to go next - **[robot/README.md](robot/README.md)**: placeholder geometry to measure, diff --git a/2026-current/hardware/openscad/PLANNING.md b/2026-current/hardware/openscad/PLANNING.md index 4883f6e..a4d63b3 100644 --- a/2026-current/hardware/openscad/PLANNING.md +++ b/2026-current/hardware/openscad/PLANNING.md @@ -189,6 +189,11 @@ charge/on LEDs show through two slots in the floor. cells dropped. Colours (owner, ASA): black case, red honeycomb (PART "inlay"), white ON/OFF (PART "text"); load "top", "inlay" and "text" as one multi-part object. Each extra colour adds a swap on the first 3 layers only. +- Printability (the STLs sliced in 0.2 mm layers, every area not carried by + the layer below listed): the brace pivot bosses stand on pillars and the + lip's tie band steps out at 45 deg (both were floating overhangs in the + first export); what's left are bridges: the 30 mm kickstand-recess roof, + the hinge trough, hole and counterbore tops, the USB-C opening. - Checked: no part collides with the shells or with each other, the shells and the inlay don't overlap, kickstand clear at 0 and 70 deg, bail clear from 0 to -180 deg (CGAL intersections). diff --git a/2026-current/hardware/openscad/remote_v2.scad b/2026-current/hardware/openscad/remote_v2.scad index e6722c7..dcb1d40 100644 --- a/2026-current/hardware/openscad/remote_v2.scad +++ b/2026-current/hardware/openscad/remote_v2.scad @@ -307,9 +307,10 @@ module bottom_shell() render(convexity = 10) difference() { offset(delta = -(T + FIT + LIP_W)) outline_2d(); for (s = SCREWS) translate(s) circle(d = BOSS_D + 2 * FIT); } - translate([0, 0, Z_SPLIT - 3]) lx(3) difference() { // ties the lip to the wall + // ties the lip to the wall; its underside steps out at 45 deg (no flat overhang) + for (i = [0 : 4]) translate([0, 0, Z_SPLIT - 3 - i * 0.35]) lx(3 + 0.01) difference() { offset(delta = -(T - JOIN)) outline_2d(); - offset(delta = -(T + FIT + LIP_W)) outline_2d(); + offset(delta = -(T + FIT + LIP_W - i * 0.35)) outline_2d(); for (s = SCREWS) translate(s) circle(d = BOSS_D + 2 * FIT); } intersection() { @@ -317,8 +318,9 @@ module bottom_shell() render(convexity = 10) difference() { union() { // screw towers for (s = SCREWS) translate([s[0], s[1], Z_BOT]) cylinder(d = BOSS_D, h = Z_SPLIT - Z_BOT); - // bail pivot bosses in the side walls - for (m = [-1, 1]) translate([m * SIDE_U, BAIL_PIVOT[0], BAIL_PIVOT[1]]) rotate([0, -m * 90, 0]) cylinder(d = 10, h = 14); + // bail pivot bosses in the side walls, on pillars down to the floor (printable) + for (m = [-1, 1]) hull() for (z = [BAIL_PIVOT[1], Z_BOT + 5]) + translate([m * SIDE_U, BAIL_PIVOT[0], z]) rotate([0, -m * 90, 0]) cylinder(d = 10, h = 14); // UPS standoffs for (m = [-1, 1]) translate([UPS_CENTRE[0] + m * UPS_HOLES, UPS_CENTRE[1], Z_BOT]) cylinder(d = 6, h = UPS_Z - Z_BOT); // kickstand recess and hinge trough walls @@ -356,7 +358,7 @@ module bottom_shell() render(convexity = 10) difference() { // pin through a barrel. Friction on the pin holds the angle. KS_RECESS = KS_T + 0.5; KS_ROOF = Z_BOT + KS_RECESS + 2; // top of the recess roof -KS_AXIS_Z = Z_BOT + KS_BARREL_D / 2 + 0.3; +KS_AXIS_Z = Z_BOT + KS_BARREL_D / 2; // barrel tangent to the underside (sits on the bed when printed) module kickstand_housing() { translate([-KS_W / 2 - FIT - KS_WALL, KS_V[0] - FIT - KS_WALL_V, Z_BOT]) cube([KS_W + 2 * (FIT + KS_WALL), KS_V[1] - KS_V[0] + KS_BARREL_D / 2 + 2 * FIT + 2 * KS_WALL_V, KS_RECESS + 2]); diff --git a/2026-current/hardware/openscad/stl/remote_v2/remote_v2_bottom.stl b/2026-current/hardware/openscad/stl/remote_v2/remote_v2_bottom.stl index d158d0a..10e7ae5 100644 --- a/2026-current/hardware/openscad/stl/remote_v2/remote_v2_bottom.stl +++ b/2026-current/hardware/openscad/stl/remote_v2/remote_v2_bottom.stl @@ -1,3 +1,3 @@ version https://git-lfs.github.com/spec/v1 -oid sha256:03b4217577659447ca7c8debfad141d1c44265622f961e5cf02ec6a04847aa75 -size 1354705 +oid sha256:71be3a8e56f5d9ed6ad4bda359f998c31eecd19228f88788836aab00f57c5272 +size 1629433 diff --git a/2026-current/hardware/openscad/stl/remote_v2/remote_v2_kickstand.stl b/2026-current/hardware/openscad/stl/remote_v2/remote_v2_kickstand.stl index 724a47b..93e9fa0 100644 --- a/2026-current/hardware/openscad/stl/remote_v2/remote_v2_kickstand.stl +++ b/2026-current/hardware/openscad/stl/remote_v2/remote_v2_kickstand.stl @@ -1,3 +1,3 @@ version https://git-lfs.github.com/spec/v1 -oid sha256:1d2286a86da4c8b812f6a1f36e9e580e50d872780ef3fac39c59b50a95bd8563 -size 61640 +oid sha256:e02ceb28e6badc6a97669d96d5864aa7afe36cb7bab545d29cc3e8cfbe34ad0c +size 61072 diff --git a/2026-current/hardware/openscad/stl/remote_v2/remote_v2_top_multicolor.3mf b/2026-current/hardware/openscad/stl/remote_v2/remote_v2_top_multicolor.3mf index a2db16f..03e6342 100644 --- a/2026-current/hardware/openscad/stl/remote_v2/remote_v2_top_multicolor.3mf +++ b/2026-current/hardware/openscad/stl/remote_v2/remote_v2_top_multicolor.3mf @@ -1,3 +1,3 @@ version https://git-lfs.github.com/spec/v1 -oid sha256:1f48afe1e86b871c1b54dd81c577aad4b93a161d1433aba5ea2ba53b307d1f67 -size 118336 +oid sha256:da78964f62d44012311f03376ed6f3eb0e7aedade38603ff33bba4532c50cdac +size 314188