2026 remote v2: printable bottom shell, notes for the PC radio link
- Bottom shell: the brace pivot bosses stand on pillars and the lip's tie band steps out at 45 deg (both were floating overhangs); the kickstand barrel sits on the bed. Checked by slicing the STLs layer by layer: only bridges are left. STLs re-exported. - remote_v2_top_multicolor.3mf: now the owner's OrcaSlicer project (all parts on two plates); export_3mf.py regenerates the plain multi-part file. - README "Planned": a USB nRF24 stick on the PC so Unity can talk to both the robot and the remote (what to work out), plus pointers to the other notes for later. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
60605209fb
commit
80270ba17e
6 files changed
+44
-11
No files matched your search
@@ -75,6 +75,32 @@ Hardware (besides the electronics of the old remote):
|
|||||||
|
|
||||||
Design notes, checks and open points: [hardware/openscad/PLANNING.md](hardware/openscad/PLANNING.md).
|
Design notes, checks and open points: [hardware/openscad/PLANNING.md](hardware/openscad/PLANNING.md).
|
||||||
|
|
||||||
|
## Planned
|
||||||
|
|
||||||
|
- **PC radio link (owner, later):** a USB nRF24L01 stick on the PC (it
|
||||||
|
probably shows up as a serial port), on the same radio as the robot and the
|
||||||
|
remote, so Unity on the PC can both receive data from (telemetry) and send
|
||||||
|
data to the robot and the remote. Not designed yet. To work out:
|
||||||
|
- what the stick's firmware does: many of these sticks are a USB-serial
|
||||||
|
chip with a microcontroller set up by AT commands (address, channel, data
|
||||||
|
rate) that passes raw payloads through; check that it can match
|
||||||
|
`HXP_RADIO_*` in `shared/HexapodProtocol/HexapodProtocol.h` (channel 96,
|
||||||
|
250 kbps, 5-byte address `HXPD1`, fixed payload of `sizeof(CmdPacket)`)
|
||||||
|
and whether it can do auto-ack and ack payloads;
|
||||||
|
- the radio protocol: today the remote only transmits a `CmdPacket` to the
|
||||||
|
robot and nothing comes back. Three nodes need an address per node (or
|
||||||
|
per pipe), a packet type byte, and telemetry back (e.g. as ack payloads
|
||||||
|
or in time slots) so the nodes don't talk over each other; who has
|
||||||
|
priority when the PC and the remote both send commands;
|
||||||
|
- Unity side: a serial-port reader/writer next to the simulation (the
|
||||||
|
2019 generation already drove the robot from Unity, through the remote
|
||||||
|
over USB: see `../2019-teensy-nrf24/`).
|
||||||
|
- Remote battery level and the IMU on the normal pin headers: see
|
||||||
|
[remote/README.md](remote/README.md), "Planned".
|
||||||
|
- Robot power: a stable 6 V supply for the 18 servos, see
|
||||||
|
[hardware/openscad/PLANNING.md](hardware/openscad/PLANNING.md), "Notes for
|
||||||
|
future designs".
|
||||||
|
|
||||||
## Where to go next
|
## Where to go next
|
||||||
|
|
||||||
- **[robot/README.md](robot/README.md)**: placeholder geometry to measure,
|
- **[robot/README.md](robot/README.md)**: placeholder geometry to measure,
|
||||||
|
|||||||
@@ -189,6 +189,11 @@ charge/on LEDs show through two slots in the floor.
|
|||||||
cells dropped. Colours (owner, ASA): black case, red honeycomb (PART
|
cells dropped. Colours (owner, ASA): black case, red honeycomb (PART
|
||||||
"inlay"), white ON/OFF (PART "text"); load "top", "inlay" and "text" as one
|
"inlay"), white ON/OFF (PART "text"); load "top", "inlay" and "text" as one
|
||||||
multi-part object. Each extra colour adds a swap on the first 3 layers only.
|
multi-part object. Each extra colour adds a swap on the first 3 layers only.
|
||||||
|
- Printability (the STLs sliced in 0.2 mm layers, every area not carried by
|
||||||
|
the layer below listed): the brace pivot bosses stand on pillars and the
|
||||||
|
lip's tie band steps out at 45 deg (both were floating overhangs in the
|
||||||
|
first export); what's left are bridges: the 30 mm kickstand-recess roof,
|
||||||
|
the hinge trough, hole and counterbore tops, the USB-C opening.
|
||||||
- Checked: no part collides with the shells or with each other, the shells
|
- Checked: no part collides with the shells or with each other, the shells
|
||||||
and the inlay don't overlap, kickstand clear at 0 and 70 deg, bail clear
|
and the inlay don't overlap, kickstand clear at 0 and 70 deg, bail clear
|
||||||
from 0 to -180 deg (CGAL intersections).
|
from 0 to -180 deg (CGAL intersections).
|
||||||
|
|||||||
@@ -307,9 +307,10 @@ module bottom_shell() render(convexity = 10) difference() {
|
|||||||
offset(delta = -(T + FIT + LIP_W)) outline_2d();
|
offset(delta = -(T + FIT + LIP_W)) outline_2d();
|
||||||
for (s = SCREWS) translate(s) circle(d = BOSS_D + 2 * FIT);
|
for (s = SCREWS) translate(s) circle(d = BOSS_D + 2 * FIT);
|
||||||
}
|
}
|
||||||
translate([0, 0, Z_SPLIT - 3]) lx(3) difference() { // ties the lip to the wall
|
// ties the lip to the wall; its underside steps out at 45 deg (no flat overhang)
|
||||||
|
for (i = [0 : 4]) translate([0, 0, Z_SPLIT - 3 - i * 0.35]) lx(3 + 0.01) difference() {
|
||||||
offset(delta = -(T - JOIN)) outline_2d();
|
offset(delta = -(T - JOIN)) outline_2d();
|
||||||
offset(delta = -(T + FIT + LIP_W)) outline_2d();
|
offset(delta = -(T + FIT + LIP_W - i * 0.35)) outline_2d();
|
||||||
for (s = SCREWS) translate(s) circle(d = BOSS_D + 2 * FIT);
|
for (s = SCREWS) translate(s) circle(d = BOSS_D + 2 * FIT);
|
||||||
}
|
}
|
||||||
intersection() {
|
intersection() {
|
||||||
@@ -317,8 +318,9 @@ module bottom_shell() render(convexity = 10) difference() {
|
|||||||
union() {
|
union() {
|
||||||
// screw towers
|
// screw towers
|
||||||
for (s = SCREWS) translate([s[0], s[1], Z_BOT]) cylinder(d = BOSS_D, h = Z_SPLIT - Z_BOT);
|
for (s = SCREWS) translate([s[0], s[1], Z_BOT]) cylinder(d = BOSS_D, h = Z_SPLIT - Z_BOT);
|
||||||
// bail pivot bosses in the side walls
|
// bail pivot bosses in the side walls, on pillars down to the floor (printable)
|
||||||
for (m = [-1, 1]) translate([m * SIDE_U, BAIL_PIVOT[0], BAIL_PIVOT[1]]) rotate([0, -m * 90, 0]) cylinder(d = 10, h = 14);
|
for (m = [-1, 1]) hull() for (z = [BAIL_PIVOT[1], Z_BOT + 5])
|
||||||
|
translate([m * SIDE_U, BAIL_PIVOT[0], z]) rotate([0, -m * 90, 0]) cylinder(d = 10, h = 14);
|
||||||
// UPS standoffs
|
// UPS standoffs
|
||||||
for (m = [-1, 1]) translate([UPS_CENTRE[0] + m * UPS_HOLES, UPS_CENTRE[1], Z_BOT]) cylinder(d = 6, h = UPS_Z - Z_BOT);
|
for (m = [-1, 1]) translate([UPS_CENTRE[0] + m * UPS_HOLES, UPS_CENTRE[1], Z_BOT]) cylinder(d = 6, h = UPS_Z - Z_BOT);
|
||||||
// kickstand recess and hinge trough walls
|
// kickstand recess and hinge trough walls
|
||||||
@@ -356,7 +358,7 @@ module bottom_shell() render(convexity = 10) difference() {
|
|||||||
// pin through a barrel. Friction on the pin holds the angle.
|
// pin through a barrel. Friction on the pin holds the angle.
|
||||||
KS_RECESS = KS_T + 0.5;
|
KS_RECESS = KS_T + 0.5;
|
||||||
KS_ROOF = Z_BOT + KS_RECESS + 2; // top of the recess roof
|
KS_ROOF = Z_BOT + KS_RECESS + 2; // top of the recess roof
|
||||||
KS_AXIS_Z = Z_BOT + KS_BARREL_D / 2 + 0.3;
|
KS_AXIS_Z = Z_BOT + KS_BARREL_D / 2; // barrel tangent to the underside (sits on the bed when printed)
|
||||||
module kickstand_housing() {
|
module kickstand_housing() {
|
||||||
translate([-KS_W / 2 - FIT - KS_WALL, KS_V[0] - FIT - KS_WALL_V, Z_BOT])
|
translate([-KS_W / 2 - FIT - KS_WALL, KS_V[0] - FIT - KS_WALL_V, Z_BOT])
|
||||||
cube([KS_W + 2 * (FIT + KS_WALL), KS_V[1] - KS_V[0] + KS_BARREL_D / 2 + 2 * FIT + 2 * KS_WALL_V, KS_RECESS + 2]);
|
cube([KS_W + 2 * (FIT + KS_WALL), KS_V[1] - KS_V[0] + KS_BARREL_D / 2 + 2 * FIT + 2 * KS_WALL_V, KS_RECESS + 2]);
|
||||||
|
|||||||
Binary file not shown.
Binary file not shown.
Binary file not shown.
Reference in new issue
Block a user