2026: remote v2 (flat console for the twist-grip sticks), STL/3MF exports, archive page
remote_v2.scad: a new remote for the same electronics, 216 x 116 x 32 mm, ASA, two shells printed without supports and joined with M3 heat-set inserts. Hangs level from a neck strap on a balance-point eyelet (top face or front edge) with a fold-out body brace; kickstand for the table. JH-D300X-R1 sticks clamp the plate; main perfboard (Teensy 4.0, nRF24, IMU) clamped at its sides under the display; UPS board with its LEDs through the floor. Red honeycomb and white ON/OFF inlays in the first 3 layers. Every part checked for collisions. - stl/remote_v2/: print-ready STLs, plus a multi-part 3MF (export_3mf.py) with the inlays on filaments 2 and 3 - ARCHIVE.md: the original remote with the owner's photos; README shows v2 and how to print it - Notes for later: battery-voltage reading, IMU on Wire (18/19) with two stick axes moved to A7/A8, a stable 6 V supply for the 18 servos - remote.scad: its sticks are JH-D300X-R1 (the model uses the D400X drawing) - *.3mf through Git LFS; repo README says Teensy 4.0 remote Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
e23216b3a1
commit
60605209fb
24 files changed
+918
-6
No files matched your search
@@ -6,6 +6,24 @@ touchscreen, and sends a `CmdPacket` (defined in
|
||||
`../shared/HexapodProtocol/HexapodProtocol.h`) to the robot over nRF24L01
|
||||
at 100 Hz.
|
||||
|
||||
## Planned
|
||||
|
||||
- **Battery level** (not built yet): read the 18650's voltage through a
|
||||
~100k/100k divider from the cell's + (not the boost board's 5 V output)
|
||||
into A6 (pin 20, free), with 100 nF to GND, and show the charge on the
|
||||
Nextion with a low-battery warning. Details in
|
||||
`../hardware/openscad/PLANNING.md` (notes for future designs).
|
||||
|
||||
- **IMU on the normal pin headers** (suggestion, not done): with the GY-521 on
|
||||
the main board, wire it to Wire (SDA 18 / SCL 19) instead of Wire2 (the
|
||||
24/25 pads under the Teensy 4.0). 18/19 are A4/A5, used by two stick axes
|
||||
now, so move those two axes to A7 (pin 21) and A8 (pin 22): all on the
|
||||
edge headers. A6 (pin 20) stays free for the battery divider, A9 (23) is
|
||||
spare. Firmware: in `Config.h` `STICK_PINS = { A0, A1, A2, A3, A7, A8 }`
|
||||
and `#define IMU_WIRE Wire`; `Sticks.cpp` reads through `STICK_PINS`, so
|
||||
nothing else changes. Redo the stick axis check (`p` dump) and calibration
|
||||
afterwards. (Wire1 is no way out: its 16/17 are stick pins A2/A3 too.)
|
||||
|
||||
## Building
|
||||
|
||||
From the `2026-current` folder: `pio run -e remote`, flash with
|
||||
|
||||
Reference in new issue
Block a user