2026: remote v2 (flat console for the twist-grip sticks), STL/3MF exports, archive page
remote_v2.scad: a new remote for the same electronics, 216 x 116 x 32 mm, ASA, two shells printed without supports and joined with M3 heat-set inserts. Hangs level from a neck strap on a balance-point eyelet (top face or front edge) with a fold-out body brace; kickstand for the table. JH-D300X-R1 sticks clamp the plate; main perfboard (Teensy 4.0, nRF24, IMU) clamped at its sides under the display; UPS board with its LEDs through the floor. Red honeycomb and white ON/OFF inlays in the first 3 layers. Every part checked for collisions. - stl/remote_v2/: print-ready STLs, plus a multi-part 3MF (export_3mf.py) with the inlays on filaments 2 and 3 - ARCHIVE.md: the original remote with the owner's photos; README shows v2 and how to print it - Notes for later: battery-voltage reading, IMU on Wire (18/19) with two stick axes moved to A7/A8, a stable 6 V supply for the 18 servos - remote.scad: its sticks are JH-D300X-R1 (the model uses the D400X drawing) - *.3mf through Git LFS; repo README says Teensy 4.0 remote Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
e23216b3a1
commit
60605209fb
24 files changed
+918
-6
No files matched your search
@@ -118,7 +118,7 @@ mm (sat in the ledge, posts overlapping the bosses); the display bezel's
|
||||
mesh facets became a clean window; the stray Body12 (an ON-OFF bracket
|
||||
line never cut in) is left out. The display is a Nextion NX4832T035
|
||||
(3.5" Basic); its board's M3 holes are the lid's 94.2 x 48.5 post grid.
|
||||
Reference parts in `remote.scad`: the joysticks are JH-D400X-R4 (4-axis,
|
||||
Reference parts in `remote.scad`: the joysticks are modelled as JH-D400X-R4 (owner's photos later showed JH-D300X-R1; 4-axis,
|
||||
X/Y ±25°, twist ±45°, button; owner), mounted with the dust cover on the
|
||||
lid's top face; their M2.5 square is 32.5 mm, so the lid's screw holes moved
|
||||
from the original's 33 mm square to 32.5. The battery is an 18650 UPS/boost
|
||||
@@ -135,8 +135,88 @@ hole-less 8 x 24 mm block as a guess.
|
||||
Open: what the 6 mm x 10 mm holes in the bottom bosses hold (magnets?), and
|
||||
whether the upper two bosses are meant to be asymmetric (x -80.387 / +82.73).
|
||||
|
||||
## Remote v2 (`remote_v2.scad`), draft 4
|
||||
|
||||
A new remote for the same electronics; `remote.scad` stays as the record of
|
||||
the printed one. How it's used (owner): the sticks are big twist grips that
|
||||
take a whole hand each, so nothing holds the case. It hangs from a neck strap
|
||||
or lies on a table. Earlier drafts: gamepad grips (dropped: nobody holds
|
||||
them), strap tabs at the rear corners (it tipped forward), a hexapod emblem
|
||||
inlay (owner preferred a honeycomb).
|
||||
|
||||
From the owner's photos and drawing: the sticks are JH-D300X-R1; the Teensy
|
||||
sits socketed on a cut perfboard (~52 x 80, estimated) with the nRF24L01
|
||||
(100 uF cap), an AMS1117, the ribbon connectors and now also the GY-521; the
|
||||
switch's plate sits on top of the case, body through the slot, and the old
|
||||
8 x 16 slot with d2 holes 19 mm apart fits it exactly; the UPS board's
|
||||
charge/on LEDs show through two slots in the floor.
|
||||
|
||||
- Size 216 x 116 x 32 mm (old remote: 208 x 175 x 45). Sticks at u +-80,
|
||||
display forward of them, strap eyelet behind the display, UPS board behind
|
||||
that, switch at the rear centre. Main board under the display.
|
||||
- JH-D300X-R1: dust cover d53.5 on the top face; the 40.4 mm control box
|
||||
(25.5 tall) against the plate's underside, 4 x M2.5 x 14 through cover and
|
||||
plate into the box (no nuts). Reaches 28.5 mm down. Pots (d16.5, 9.2 out)
|
||||
towards the middle and towards the user.
|
||||
- Display mounted turned 180 deg so its J1 connector is on the right, clear
|
||||
of the Teensy's USB plug: set display direction 180 in the Nextion Editor.
|
||||
Glass 1.5 mm under the top face, board on 4 posts (M2.5 self-tapping);
|
||||
the LCD thickness (4.5) is a guess.
|
||||
- Main board clamped at 4 points on its long sides, no holes in the board
|
||||
(owner): posts beside the edges carry it, M3 x 8 button heads with d7
|
||||
washers in heat-set inserts clamp the edge. 2 mm above the kickstand
|
||||
recess for the wires underneath; Teensy micro-USB to the left, nRF24 to
|
||||
the right. The cable plug clears the display board by ~0.2 mm and the left
|
||||
stick's pot narrowly: plug and board sizes are estimates.
|
||||
- UPS board on 2 standoffs behind the eyelet, Type-C end to the right (room
|
||||
for the cut cable's plug); LEDs through 2 x 6 mm floor slots.
|
||||
- Strap eyelet (separate part, 2 x M3 into heat-set inserts): on the top face
|
||||
behind the display (slots +-5 mm to balance it), or on the front face (the
|
||||
edge away from you, 2 more inserts at Z -19). Folded forward, the bail
|
||||
hits a front-mounted eyelet: then park the bail back or down.
|
||||
- Brace bail: U pivoting on the side faces (v -25, Z -22), M3 x 16 into
|
||||
heat-set inserts; 0 = folded forward, -150 = brace against chest or belly,
|
||||
-180 = straight back. Swings down under the case.
|
||||
- Kickstand: 30 x 35 mm flap in a recess in the underside, hinged at the front
|
||||
on an M3 x 40 into a nut trap; lifts the front a little on a table.
|
||||
- Shells split at Z -12, both print without supports (top face down, bottom
|
||||
on its flat underside), 45 deg chamfers, 1.2 mm locating lip, 4 x M3 x 12
|
||||
from below into heat-set inserts. USB-C breakout glued into a pocket at
|
||||
the front left, receptacle 0.6 mm inside the front face.
|
||||
- Inlay (second colour, first 3 layers of the face-down top shell): ON/OFF
|
||||
plus a honeycomb of whole cells (4.5 mm, 1.2 mm walls) right of a diagonal
|
||||
through the middle, clear of display, sticks, eyelet and switch; lone
|
||||
cells dropped. Colours (owner, ASA): black case, red honeycomb (PART
|
||||
"inlay"), white ON/OFF (PART "text"); load "top", "inlay" and "text" as one
|
||||
multi-part object. Each extra colour adds a swap on the first 3 layers only.
|
||||
- Checked: no part collides with the shells or with each other, the shells
|
||||
and the inlay don't overlap, kickstand clear at 0 and 70 deg, bail clear
|
||||
from 0 to -180 deg (CGAL intersections).
|
||||
- Open: perfboard size and holes, Teensy cable plug size, LCD thickness, UPS
|
||||
hole spacing; hand room untested; set `IMU_AXIS_FROM_CHIP` /
|
||||
`IMU_AXIS_SIGN` in `remote/Config.h` for the IMU on the main board.
|
||||
|
||||
## Notes for future designs
|
||||
|
||||
- Robot power (still to choose): a battery or supply that gives a **stable
|
||||
6 V** with enough current for all 18 servos (12 x HS-485HB + 6 stronger
|
||||
ones of the same size). Servos draw well over 1 A each when stalled or
|
||||
starting, and many move at once while walking, so plan for a 6 V regulator
|
||||
/ UBEC of 15-20 A peak (e.g. a 2S LiPo through a high-current 6 V BEC), or
|
||||
a pack that stays near 6 V under that load. Check the servos' datasheet
|
||||
for the stall current. The battery must also fit the bay (see open
|
||||
question 3) and leave room for the servo plugs.
|
||||
|
||||
- Remote: connect the IMU to the normal pin headers instead of the Teensy
|
||||
4.0's underside pads; see `remote/README.md`, "Planned" (Wire on 18/19,
|
||||
the two stick axes there move to A7/A8).
|
||||
|
||||
- Remote: measure the 18650's voltage on the Teensy to show how much charge
|
||||
is left (owner, later). Divider ~100k/100k from the cell's + (holder or the
|
||||
UPS board's B+, not the 5 V output) to A6 (pin 20, free), 100 nF to GND;
|
||||
full cell = ~2.1 V at the pin. Firmware: average, Li-ion curve to %, show
|
||||
on the Nextion with a low-battery warning (optionally send it to the robot).
|
||||
|
||||
- Servo wires barely fit on the real robot: the six servo headers hang
|
||||
above the battery bay, and the front pair sits right over the bay's end
|
||||
stop (X 28.8..31.8, top at Z 13.5). Kept as-is for now; give the plugs and
|
||||
|
||||
Reference in new issue
Block a user