2026: remote v2 (flat console for the twist-grip sticks), STL/3MF exports, archive page

remote_v2.scad: a new remote for the same electronics, 216 x 116 x 32 mm,
ASA, two shells printed without supports and joined with M3 heat-set
inserts. Hangs level from a neck strap on a balance-point eyelet (top face
or front edge) with a fold-out body brace; kickstand for the table.
JH-D300X-R1 sticks clamp the plate; main perfboard (Teensy 4.0, nRF24,
IMU) clamped at its sides under the display; UPS board with its LEDs
through the floor. Red honeycomb and white ON/OFF inlays in the first
3 layers. Every part checked for collisions.

- stl/remote_v2/: print-ready STLs, plus a multi-part 3MF (export_3mf.py)
  with the inlays on filaments 2 and 3
- ARCHIVE.md: the original remote with the owner's photos; README shows v2
  and how to print it
- Notes for later: battery-voltage reading, IMU on Wire (18/19) with two
  stick axes moved to A7/A8, a stable 6 V supply for the 18 servos
- remote.scad: its sticks are JH-D300X-R1 (the model uses the D400X drawing)
- *.3mf through Git LFS; repo README says Teensy 4.0 remote

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
mangavalkandClaude Opus 5.5 committed 2026-11-14 18:57:49 +01:00
1 parent e23216b3a1
commit 60605209fb
24 files changed
+918 -6

No files matched your search

+37
View File
@@ -0,0 +1,37 @@
# Archive: earlier designs
Designs that are no longer the current ones, kept for reference. The
current remote is `remote_v2.scad` (see [../../README.md](../../README.md)).
## Original remote (`remote.scad`)
![The original remote, OpenSCAD model](renders/remote.png)
The remote used with the robot until 2026: a 208 x 175 x 45 mm box printed
from the Fusion 360 design `../fusion360/remote/remote v40.f3d`.
`remote.scad` rebuilds it from that file's solids (details, and the bugs
fixed in the rebuild, in [PLANNING.md](PLANNING.md), section "Remote").
What's inside (from the owner and the photos below):
- Two joysticks, JH-D300X-R1 (3-axis twist grip), on the lid. The model
uses the similar JH-D400X-R4 drawing.
- Nextion NX4832T035 3.5" display under a window in the lid.
- A Teensy 4.0 socketed on a cut perfboard with the nRF24L01 (100 uF cap)
and an AMS1117 regulator.
- An MPU6050 (GY-521) on the big standoff in the middle.
- An 18650 UPS/boost board on two standoffs, with its charge and on LEDs
visible through two small slots in the floor.
- A USB-C breakout glued into the holder at the side port.
- A slide switch mounted on top of the lid, and a lanyard loop on the bump.
Photos of the printed remote, opened: [original remote/](original%20remote/).
| | |
|---|---|
| ![Lid from inside: Nextion and joysticks](original%20remote/20261114_175520.jpg) | ![Bottom shell: main board, battery, IMU, USB-C](original%20remote/20261114_175548.jpg) |
| ![Main board, top](original%20remote/20261114_175504.jpg) | ![Main board, wiring underneath](original%20remote/20261114_175509.jpg) |
Why it was replaced: the new remote (`remote_v2.scad`) is smaller
(216 x 116 x 32 mm), prints in ASA without supports, hangs level from a neck
strap (a balance-point eyelet and a body brace), and stands on a table.