2026: remote v2 (flat console for the twist-grip sticks), STL/3MF exports, archive page
remote_v2.scad: a new remote for the same electronics, 216 x 116 x 32 mm, ASA, two shells printed without supports and joined with M3 heat-set inserts. Hangs level from a neck strap on a balance-point eyelet (top face or front edge) with a fold-out body brace; kickstand for the table. JH-D300X-R1 sticks clamp the plate; main perfboard (Teensy 4.0, nRF24, IMU) clamped at its sides under the display; UPS board with its LEDs through the floor. Red honeycomb and white ON/OFF inlays in the first 3 layers. Every part checked for collisions. - stl/remote_v2/: print-ready STLs, plus a multi-part 3MF (export_3mf.py) with the inlays on filaments 2 and 3 - ARCHIVE.md: the original remote with the owner's photos; README shows v2 and how to print it - Notes for later: battery-voltage reading, IMU on Wire (18/19) with two stick axes moved to A7/A8, a stable 6 V supply for the 18 servos - remote.scad: its sticks are JH-D300X-R1 (the model uses the D400X drawing) - *.3mf through Git LFS; repo README says Teensy 4.0 remote Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
e23216b3a1
commit
60605209fb
24 files changed
+918
-6
No files matched your search
+36
-2
@@ -4,7 +4,11 @@ A six-legged walking robot (Teensy 3.6) and its handheld remote
|
||||
(Teensy 4.0 + Nextion touchscreen), linked over nRF24L01.
|
||||
|
||||

|
||||

|
||||

|
||||
|
||||
The remote above is the new design (`hardware/openscad/remote_v2.scad`, not
|
||||
printed yet). The original printed remote is on the
|
||||
[archive page](hardware/openscad/ARCHIVE.md).
|
||||
|
||||
```
|
||||
robot/ robot firmware: IK, gait, body pose, IMU stabilization, state machine
|
||||
@@ -12,7 +16,8 @@ remote/ remote firmware: 2 x 3-axis sticks, MPU6050 tilt, Nex
|
||||
shared/ HexapodProtocol: the CmdPacket wire format + radio settings used by both
|
||||
sim/ the unchanged robot firmware compiled into a DLL for the simulation
|
||||
Hexapod_Simulation_Unity/ Unity project that runs that DLL on the 3D model
|
||||
hardware/openscad/ OpenSCAD model of the robot and remote, rebuilt from the Fusion designs
|
||||
hardware/openscad/ OpenSCAD model of the robot (rebuilt from the Fusion designs) and the new remote
|
||||
hardware/openscad/stl/ print-ready STL exports
|
||||
hardware/fusion360/ Fusion 360 designs: body, legs, servo, servo horn, remote case
|
||||
scripts/ PlatformIO helper (per-environment sketch folder)
|
||||
```
|
||||
@@ -41,6 +46,35 @@ From this `2026-current` folder in PowerShell (the dev PC is Windows):
|
||||
Then open `Hexapod_Simulation_Unity` and press Play. See
|
||||
[sim/README.md](sim/README.md).
|
||||
|
||||
## Printing the remote (v2)
|
||||
|
||||
STLs in [hardware/openscad/stl/remote_v2/](hardware/openscad/stl/remote_v2/),
|
||||
already in print orientation; everything prints in ASA without supports.
|
||||
Regenerate them from `remote_v2.scad` with `-D 'PART="..."'`.
|
||||
|
||||
| File | Part | Notes |
|
||||
|------|------|-------|
|
||||
| `remote_v2_top_multicolor.3mf` | top shell with both inlays | One object with three parts on filaments 1/2/3: case black, honeycomb red, ON/OFF white. The inlays are the first 3 layers (0.6 mm) of the face-down shell, so the colour swaps only happen there. Made by `hardware/openscad/export_3mf.py` from the three STLs below |
|
||||
| `remote_v2_top.stl` + `_inlay.stl` + `_text.stl` | the same, as STLs | Load the three at once and keep them as one multi-part object |
|
||||
| `remote_v2_bottom.stl` | bottom shell | flat underside on the bed |
|
||||
| `remote_v2_kickstand.stl` | table stand | |
|
||||
| `remote_v2_eyelet.stl` | neck-strap eyelet | on the top face (slots to balance it) or on the front edge |
|
||||
| `remote_v2_bail.stl` | body brace | swings down and back to rest against your body |
|
||||
|
||||
Hardware (besides the electronics of the old remote):
|
||||
|
||||
- 14 x M3 heat-set inserts (4.0 mm hole, ~5.7 mm long): 4 shell screws,
|
||||
2 + 2 eyelet (top and front), 2 brace pivots, 4 main-board clamps
|
||||
- M3 x 12 x 4 (shells), M3 x 8 button head x 2 (eyelet), M3 x 16 button
|
||||
head + washer x 2 (brace), M3 x 8 button head + 7 mm washer x 4 (main
|
||||
board clamps, no holes in the board), M3 x 40 + nut (kickstand pin)
|
||||
- M2.5 x 14 x 8 (joysticks, into their own boxes), M2.5 self-tapping x 4
|
||||
(display), M3 self-tapping x 2 (UPS board), M2 self-tapping x 2 (switch)
|
||||
- Set the Nextion's display direction to 180 in the Nextion Editor: the
|
||||
display is mounted turned round so its connector clears the Teensy's USB plug.
|
||||
|
||||
Design notes, checks and open points: [hardware/openscad/PLANNING.md](hardware/openscad/PLANNING.md).
|
||||
|
||||
## Where to go next
|
||||
|
||||
- **[robot/README.md](robot/README.md)**: placeholder geometry to measure,
|
||||
|
||||
Reference in new issue
Block a user