2026 remote_v2 case: taller top shell, measured display, M3 display posts
- TOP_GROW: top shell 10 mm taller (room behind the display); the bottom shell is unchanged, dependent heights follow Z_SPLIT / Z_BOT. - Nextion dimensions as measured by the owner: board 100.6 x 55, LCD 85.7 x 55 x 3.86 plus a 1.3 mm flex cable, 11.21 mm glass to back of J1. LCD pocket allows the cable on either short side; bezel 1.0 mm (the display sat on the Teensy). - Display posts tapped M3 for M3 x 5 machine screws, 1.2 mm skin under the top face (was M2.5 self-tapping). README screw list and PLANNING.md updated; STLs regenerated. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
2b4750f8f4
commit
3d6c4dd2f0
6 files changed
+32
-26
No files matched your search
@@ -70,8 +70,8 @@ Hardware (besides the electronics of the old remote):
|
|||||||
- M3 x 12 x 4 (shells), M3 x 8 button head x 2 (eyelet), M3 x 16 button
|
- M3 x 12 x 4 (shells), M3 x 8 button head x 2 (eyelet), M3 x 16 button
|
||||||
head + washer x 2 (brace), M3 x 8 button head + 7 mm washer x 4 (main
|
head + washer x 2 (brace), M3 x 8 button head + 7 mm washer x 4 (main
|
||||||
board clamps, no holes in the board), M3 x 40 + nut (kickstand pin)
|
board clamps, no holes in the board), M3 x 40 + nut (kickstand pin)
|
||||||
- M2.5 x 14 x 8 (joysticks, into their own boxes), M2.5 self-tapping x 4
|
- M2.5 x 14 x 8 (joysticks, into their own boxes), M3 x 5 machine screws x 4
|
||||||
(display), M3 self-tapping x 2 (UPS board), M2 self-tapping x 2 (switch)
|
(display, tap the posts M3), M3 self-tapping x 2 (UPS board), M2 self-tapping x 2 (switch)
|
||||||
- Set the Nextion's display direction to 180 in the Nextion Editor: the
|
- Set the Nextion's display direction to 180 in the Nextion Editor: the
|
||||||
display is mounted turned round so its connector clears the Teensy's USB plug.
|
display is mounted turned round so its connector clears the Teensy's USB plug.
|
||||||
|
|
||||||
|
|||||||
@@ -151,7 +151,7 @@ switch's plate sits on top of the case, body through the slot, and the old
|
|||||||
8 x 16 slot with d2 holes 19 mm apart fits it exactly; the UPS board's
|
8 x 16 slot with d2 holes 19 mm apart fits it exactly; the UPS board's
|
||||||
charge/on LEDs show through two slots in the floor.
|
charge/on LEDs show through two slots in the floor.
|
||||||
|
|
||||||
- Size 216 x 116 x 32 mm (old remote: 208 x 175 x 45). Sticks at u +-80,
|
- Size 216 x 116 x 42 mm (top shell 10 mm taller than first printed, TOP_GROW: room behind the display) (old remote: 208 x 175 x 45). Sticks at u +-80,
|
||||||
display forward of them, strap eyelet behind the display, UPS board behind
|
display forward of them, strap eyelet behind the display, UPS board behind
|
||||||
that, switch at the rear centre. Main board under the display.
|
that, switch at the rear centre. Main board under the display.
|
||||||
- JH-D300X-R1: dust cover d53.5 on the top face; the 40.4 mm control box
|
- JH-D300X-R1: dust cover d53.5 on the top face; the 40.4 mm control box
|
||||||
@@ -160,8 +160,9 @@ charge/on LEDs show through two slots in the floor.
|
|||||||
towards the middle and towards the user.
|
towards the middle and towards the user.
|
||||||
- Display mounted turned 180 deg so its J1 connector is on the right, clear
|
- Display mounted turned 180 deg so its J1 connector is on the right, clear
|
||||||
of the Teensy's USB plug: set display direction 180 in the Nextion Editor.
|
of the Teensy's USB plug: set display direction 180 in the Nextion Editor.
|
||||||
Glass 1.5 mm under the top face, board on 4 posts (M2.5 self-tapping);
|
Glass 1.0 mm under the top face, board on 4 posts tapped M3 (3.66 mm of thread, 1.2 mm under the top face);
|
||||||
the LCD thickness (4.5) is a guess.
|
LCD 85.7 x 55 x 3.86 plus a 1.3 mm flex cable on one side, 11.21 mm glass to
|
||||||
|
back of J1 (owner measured).
|
||||||
- Main board clamped at 4 points on its long sides, no holes in the board
|
- Main board clamped at 4 points on its long sides, no holes in the board
|
||||||
(owner): posts beside the edges carry it, M3 x 8 button heads with d7
|
(owner): posts beside the edges carry it, M3 x 8 button heads with d7
|
||||||
washers in heat-set inserts clamp the edge. 2 mm above the kickstand
|
washers in heat-set inserts clamp the edge. 2 mm above the kickstand
|
||||||
|
|||||||
@@ -27,8 +27,9 @@
|
|||||||
/* [Shell] */
|
/* [Shell] */
|
||||||
T = 2.4; // walls and floor (6 perimeters of 0.4)
|
T = 2.4; // walls and floor (6 perimeters of 0.4)
|
||||||
PLATE = 3.0; // top plate
|
PLATE = 3.0; // top plate
|
||||||
Z_BOT = -32; // flat underside (32 mm thick: the D300X sticks reach 28.5 down)
|
TOP_GROW = 10; // extra height of the top shell only (room behind the display); the bottom shell is unchanged
|
||||||
Z_SPLIT = -12; // top shell / bottom shell
|
Z_BOT = -32 - TOP_GROW; // flat underside (32 mm thick before TOP_GROW: the D300X sticks reach 28.5 down)
|
||||||
|
Z_SPLIT = -12 - TOP_GROW; // top shell / bottom shell
|
||||||
CHAMFER = 4; // 45 deg bottom edge (printable without support)
|
CHAMFER = 4; // 45 deg bottom edge (printable without support)
|
||||||
TOP_CHAMFER = 1.5; // 45 deg top edge (the top shell prints face down)
|
TOP_CHAMFER = 1.5; // 45 deg top edge (the top shell prints face down)
|
||||||
LIP_H = 2.5; // locating lip on the bottom shell, into the top shell
|
LIP_H = 2.5; // locating lip on the bottom shell, into the top shell
|
||||||
@@ -53,7 +54,7 @@ INSERT_D = 4.0;
|
|||||||
INSERT_L = 6;
|
INSERT_L = 6;
|
||||||
SCREW_D = 3.4;
|
SCREW_D = 3.4;
|
||||||
HEAD_D = 6.5;
|
HEAD_D = 6.5;
|
||||||
HEAD_Z = -19; // counterbore floor: 7 mm of tower + 5 mm into the insert
|
HEAD_Z = Z_SPLIT - 7; // counterbore floor: 7 mm of tower + 5 mm into the insert
|
||||||
|
|
||||||
/* [Joysticks] */
|
/* [Joysticks] */
|
||||||
STICK_HOLE_D = 40;
|
STICK_HOLE_D = 40;
|
||||||
@@ -61,18 +62,21 @@ STICK_SCREW = 16.25; // 4 x M2.5 x 14 on a 32.5 mm square, through cover and
|
|||||||
STICK_SCREW_D = 2.8;
|
STICK_SCREW_D = 2.8;
|
||||||
|
|
||||||
/* [Display: Nextion NX4832T035] */
|
/* [Display: Nextion NX4832T035] */
|
||||||
NX_BOARD = [100.5, 54.94];
|
NX_BOARD = [100.6, 55]; // measured by the owner
|
||||||
NX_HOLES = [94.2, 48.5]; // M3 grid, centred on the board
|
NX_HOLES = [94.2, 48.5]; // M3 grid, centred on the board
|
||||||
NX_CENTRE = [0, 20]; // board centre (forward of the sticks, so the strap misses it)
|
NX_CENTRE = [0, 20]; // board centre (forward of the sticks, so the strap misses it)
|
||||||
NX_FLIP = true; // display mounted turned 180 deg (its J1 connector on the right, clear of
|
NX_FLIP = true; // display mounted turned 180 deg (its J1 connector on the right, clear of
|
||||||
// the Teensy's USB plug): set display direction 180 in the Nextion Editor
|
// the Teensy's USB plug): set display direction 180 in the Nextion Editor
|
||||||
NX_WIN_OFF = [NX_FLIP ? 2.15 : -2.15, 0]; // window (visible area) centre from the board centre
|
NX_WIN_OFF = [NX_FLIP ? 2.15 : -2.15, 0]; // window (visible area) centre from the board centre
|
||||||
NX_WINDOW = [75.9, 50.9]; // opening in the plate
|
NX_WINDOW = [75.9, 50.9]; // opening in the plate
|
||||||
NX_LCD = [84, 54]; // LCD module outline
|
NX_LCD = [85.7, 55]; // LCD module outline (owner: 7.45 mm of board beside it on both sides, centred on the board)
|
||||||
NX_LCD_T = 4.5; // LCD thickness: approximate, measure before printing
|
NX_LCD_CABLE = 1.3; // its flex cable sticks out this much on one short side (87 mm overall)
|
||||||
NX_BEZEL = 1.5; // plate left above the glass
|
NX_LCD_T = 3.86; // LCD thickness (owner)
|
||||||
NX_POST_D = 5.5; // clears the LCD module by 0.2 mm
|
NX_BACK = 11.21 - NX_LCD_T - 1.6; // board underside to back of the J1 connector (owner: 11.21 from the glass)
|
||||||
NX_SCREW_D = 2.2; // M2.5 self-tapping through the board
|
NX_BEZEL = 1.0; // plate left above the glass (was 1.5: the display sat on the Teensy)
|
||||||
|
NX_POST_D = 5.5; // clears the LCD module (with its cable) by 0.2 mm
|
||||||
|
NX_SCREW_D = 2.5; // M3 tap drill: tap the posts for M3 x 5 machine screws through the board
|
||||||
|
NX_SKIN = 1.2; // plastic left between the tapped hole and the top face
|
||||||
|
|
||||||
/* [Switch: slide switch, mounted on top] */
|
/* [Switch: slide switch, mounted on top] */
|
||||||
SWITCH_POS = [0, -56];
|
SWITCH_POS = [0, -56];
|
||||||
@@ -128,7 +132,7 @@ HOOK_INSERTS = 7; // +- u
|
|||||||
HOOK_BASE = [24, 18, 4]; // u, v, Z
|
HOOK_BASE = [24, 18, 4]; // u, v, Z
|
||||||
// Alternative place: the front face (the edge away from you), 2 inserts in
|
// Alternative place: the front face (the edge away from you), 2 inserts in
|
||||||
// the front wall of the bottom shell; the loop then points forward.
|
// the front wall of the bottom shell; the loop then points forward.
|
||||||
HOOK_FRONT_Z = -19;
|
HOOK_FRONT_Z = Z_SPLIT - 7;
|
||||||
HOOK_MOUNT = "top"; // [top, front] (assembly view only)
|
HOOK_MOUNT = "top"; // [top, front] (assembly view only)
|
||||||
HOOK_HOLE_D = 8; // for the snap hook
|
HOOK_HOLE_D = 8; // for the snap hook
|
||||||
HOOK_H = 16; // top of the loop above the top face
|
HOOK_H = 16; // top of the loop above the top face
|
||||||
@@ -138,7 +142,7 @@ HOOK_H = 16; // top of the loop above the top face
|
|||||||
// hands. Folded forward it wraps the front edge; swung back and down its
|
// hands. Folded forward it wraps the front edge; swung back and down its
|
||||||
// crossbar rests against your chest or belly. M3 x 16 button-head screws
|
// crossbar rests against your chest or belly. M3 x 16 button-head screws
|
||||||
// with a washer into heat-set inserts in the side walls; friction holds it.
|
// with a washer into heat-set inserts in the side walls; friction holds it.
|
||||||
BAIL_PIVOT = [-25, -22]; // v, Z on the side faces (u +-SIDE_U)
|
BAIL_PIVOT = [-25, Z_BOT + 10]; // v, Z on the side faces (u +-SIDE_U)
|
||||||
BAIL_L = 82; // pivot to crossbar centre line
|
BAIL_L = 82; // pivot to crossbar centre line
|
||||||
BAIL_BOW = 10; // crossbar bows outwards by this much in the middle
|
BAIL_BOW = 10; // crossbar bows outwards by this much in the middle
|
||||||
BAIL_T = 5; // arm thickness (u)
|
BAIL_T = 5; // arm thickness (u)
|
||||||
@@ -217,8 +221,9 @@ module top_shell() render(convexity = 10) difference() {
|
|||||||
translate([0, 0, 0.005]) cube(concat(NX_WINDOW, 0.01), center = true);
|
translate([0, 0, 0.005]) cube(concat(NX_WINDOW, 0.01), center = true);
|
||||||
translate([0, 0, NX_BEZEL + 0.01]) cube(concat(NX_WINDOW + [2, 2] * NX_BEZEL, 0.02), center = true);
|
translate([0, 0, NX_BEZEL + 0.01]) cube(concat(NX_WINDOW + [2, 2] * NX_BEZEL, 0.02), center = true);
|
||||||
}
|
}
|
||||||
translate(concat(NX_WIN - (NX_LCD + [1, 1]) / 2, -PLATE - 1)) cube(concat(NX_LCD + [1, 1], PLATE + 1 - NX_BEZEL));
|
// LCD pocket: cable allowance on both short sides, so it fits either way round
|
||||||
nx_holes() translate([0, 0, NX_BOARD_TOP - 1]) cylinder(d = NX_SCREW_D, h = 1 + 4.5);
|
translate(concat(NX_CENTRE - (NX_LCD + [2 * NX_LCD_CABLE + 0.4, 1]) / 2, -PLATE - 1)) cube(concat(NX_LCD + [2 * NX_LCD_CABLE + 0.4, 1], PLATE + 1 - NX_BEZEL));
|
||||||
|
nx_holes() translate([0, 0, NX_BOARD_TOP - 1]) cylinder(d = NX_SCREW_D, h = 1 - NX_BOARD_TOP - NX_SKIN);
|
||||||
// joysticks
|
// joysticks
|
||||||
for (s = STICKS) translate([s[0], s[1], -BIG / 2]) cylinder(d = STICK_HOLE_D, h = BIG);
|
for (s = STICKS) translate([s[0], s[1], -BIG / 2]) cylinder(d = STICK_HOLE_D, h = BIG);
|
||||||
stick_screws() translate([0, 0, -BIG / 2]) cylinder(d = STICK_SCREW_D, h = BIG);
|
stick_screws() translate([0, 0, -BIG / 2]) cylinder(d = STICK_SCREW_D, h = BIG);
|
||||||
@@ -450,9 +455,9 @@ module nextion() {
|
|||||||
translate(concat(-NX_BOARD / 2, 0)) cube(concat(NX_BOARD, 1.6));
|
translate(concat(-NX_BOARD / 2, 0)) cube(concat(NX_BOARD, 1.6));
|
||||||
for (du = [-1, 1], dv = [-1, 1]) translate([du * NX_HOLES[0], dv * NX_HOLES[1], 0] / 2 + [0, 0, -1]) cylinder(d = 3.2, h = 4);
|
for (du = [-1, 1], dv = [-1, 1]) translate([du * NX_HOLES[0], dv * NX_HOLES[1], 0] / 2 + [0, 0, -1]) cylinder(d = 3.2, h = 4);
|
||||||
}
|
}
|
||||||
translate(concat(NX_WIN - NX_LCD / 2, NX_BOARD_TOP)) color("#202020") cube(concat(NX_LCD, NX_LCD_T));
|
translate(concat(NX_CENTRE - NX_LCD / 2, NX_BOARD_TOP)) color("#202020") cube(concat(NX_LCD, NX_LCD_T));
|
||||||
translate(concat(NX_WIN - [73.44, 48.96] / 2, -NX_BEZEL - 0.2)) color("#3050a0") cube([73.44, 48.96, 0.2]);
|
translate(concat(NX_WIN - [73.44, 48.96] / 2, -NX_BEZEL - 0.2)) color("#3050a0") cube([73.44, 48.96, 0.2]);
|
||||||
translate(concat(NX_CENTRE + [(NX_FLIP ? 1 : -1) * (NX_BOARD[0] / 2 - 7), -5], NX_BOARD_TOP - 1.6 - 6)) color("#eee") cube([6, 10, 6]); // J1 4-pin connector (approx.)
|
translate(concat(NX_CENTRE + [(NX_FLIP ? 1 : -1) * (NX_BOARD[0] / 2 - 7), -5], NX_BOARD_TOP - 1.6 - NX_BACK)) color("#eee") cube([6, 10, NX_BACK]); // J1 4-pin connector (approx.)
|
||||||
}
|
}
|
||||||
|
|
||||||
module ups_18650() translate(concat(UPS_CENTRE, UPS_Z)) {
|
module ups_18650() translate(concat(UPS_CENTRE, UPS_Z)) {
|
||||||
|
|||||||
Binary file not shown.
Binary file not shown.
Binary file not shown.
Reference in new issue
Block a user