diff --git a/2026-current/README.md b/2026-current/README.md index 5400289..e90eab3 100644 --- a/2026-current/README.md +++ b/2026-current/README.md @@ -70,8 +70,8 @@ Hardware (besides the electronics of the old remote): - M3 x 12 x 4 (shells), M3 x 8 button head x 2 (eyelet), M3 x 16 button head + washer x 2 (brace), M3 x 8 button head + 7 mm washer x 4 (main board clamps, no holes in the board), M3 x 40 + nut (kickstand pin) -- M2.5 x 14 x 8 (joysticks, into their own boxes), M2.5 self-tapping x 4 - (display), M3 self-tapping x 2 (UPS board), M2 self-tapping x 2 (switch) +- M2.5 x 14 x 8 (joysticks, into their own boxes), M3 x 5 machine screws x 4 + (display, tap the posts M3), M3 self-tapping x 2 (UPS board), M2 self-tapping x 2 (switch) - Set the Nextion's display direction to 180 in the Nextion Editor: the display is mounted turned round so its connector clears the Teensy's USB plug. diff --git a/2026-current/hardware/openscad/PLANNING.md b/2026-current/hardware/openscad/PLANNING.md index 06477e5..fe1f3ef 100644 --- a/2026-current/hardware/openscad/PLANNING.md +++ b/2026-current/hardware/openscad/PLANNING.md @@ -151,7 +151,7 @@ switch's plate sits on top of the case, body through the slot, and the old 8 x 16 slot with d2 holes 19 mm apart fits it exactly; the UPS board's charge/on LEDs show through two slots in the floor. -- Size 216 x 116 x 32 mm (old remote: 208 x 175 x 45). Sticks at u +-80, +- Size 216 x 116 x 42 mm (top shell 10 mm taller than first printed, TOP_GROW: room behind the display) (old remote: 208 x 175 x 45). Sticks at u +-80, display forward of them, strap eyelet behind the display, UPS board behind that, switch at the rear centre. Main board under the display. - JH-D300X-R1: dust cover d53.5 on the top face; the 40.4 mm control box @@ -160,8 +160,9 @@ charge/on LEDs show through two slots in the floor. towards the middle and towards the user. - Display mounted turned 180 deg so its J1 connector is on the right, clear of the Teensy's USB plug: set display direction 180 in the Nextion Editor. - Glass 1.5 mm under the top face, board on 4 posts (M2.5 self-tapping); - the LCD thickness (4.5) is a guess. + Glass 1.0 mm under the top face, board on 4 posts tapped M3 (3.66 mm of thread, 1.2 mm under the top face); + LCD 85.7 x 55 x 3.86 plus a 1.3 mm flex cable on one side, 11.21 mm glass to + back of J1 (owner measured). - Main board clamped at 4 points on its long sides, no holes in the board (owner): posts beside the edges carry it, M3 x 8 button heads with d7 washers in heat-set inserts clamp the edge. 2 mm above the kickstand diff --git a/2026-current/hardware/openscad/remote_v2.scad b/2026-current/hardware/openscad/remote_v2.scad index 20da11c..275a7cc 100644 --- a/2026-current/hardware/openscad/remote_v2.scad +++ b/2026-current/hardware/openscad/remote_v2.scad @@ -27,8 +27,9 @@ /* [Shell] */ T = 2.4; // walls and floor (6 perimeters of 0.4) PLATE = 3.0; // top plate -Z_BOT = -32; // flat underside (32 mm thick: the D300X sticks reach 28.5 down) -Z_SPLIT = -12; // top shell / bottom shell +TOP_GROW = 10; // extra height of the top shell only (room behind the display); the bottom shell is unchanged +Z_BOT = -32 - TOP_GROW; // flat underside (32 mm thick before TOP_GROW: the D300X sticks reach 28.5 down) +Z_SPLIT = -12 - TOP_GROW; // top shell / bottom shell CHAMFER = 4; // 45 deg bottom edge (printable without support) TOP_CHAMFER = 1.5; // 45 deg top edge (the top shell prints face down) LIP_H = 2.5; // locating lip on the bottom shell, into the top shell @@ -53,7 +54,7 @@ INSERT_D = 4.0; INSERT_L = 6; SCREW_D = 3.4; HEAD_D = 6.5; -HEAD_Z = -19; // counterbore floor: 7 mm of tower + 5 mm into the insert +HEAD_Z = Z_SPLIT - 7; // counterbore floor: 7 mm of tower + 5 mm into the insert /* [Joysticks] */ STICK_HOLE_D = 40; @@ -61,18 +62,21 @@ STICK_SCREW = 16.25; // 4 x M2.5 x 14 on a 32.5 mm square, through cover and STICK_SCREW_D = 2.8; /* [Display: Nextion NX4832T035] */ -NX_BOARD = [100.5, 54.94]; +NX_BOARD = [100.6, 55]; // measured by the owner NX_HOLES = [94.2, 48.5]; // M3 grid, centred on the board NX_CENTRE = [0, 20]; // board centre (forward of the sticks, so the strap misses it) NX_FLIP = true; // display mounted turned 180 deg (its J1 connector on the right, clear of // the Teensy's USB plug): set display direction 180 in the Nextion Editor NX_WIN_OFF = [NX_FLIP ? 2.15 : -2.15, 0]; // window (visible area) centre from the board centre NX_WINDOW = [75.9, 50.9]; // opening in the plate -NX_LCD = [84, 54]; // LCD module outline -NX_LCD_T = 4.5; // LCD thickness: approximate, measure before printing -NX_BEZEL = 1.5; // plate left above the glass -NX_POST_D = 5.5; // clears the LCD module by 0.2 mm -NX_SCREW_D = 2.2; // M2.5 self-tapping through the board +NX_LCD = [85.7, 55]; // LCD module outline (owner: 7.45 mm of board beside it on both sides, centred on the board) +NX_LCD_CABLE = 1.3; // its flex cable sticks out this much on one short side (87 mm overall) +NX_LCD_T = 3.86; // LCD thickness (owner) +NX_BACK = 11.21 - NX_LCD_T - 1.6; // board underside to back of the J1 connector (owner: 11.21 from the glass) +NX_BEZEL = 1.0; // plate left above the glass (was 1.5: the display sat on the Teensy) +NX_POST_D = 5.5; // clears the LCD module (with its cable) by 0.2 mm +NX_SCREW_D = 2.5; // M3 tap drill: tap the posts for M3 x 5 machine screws through the board +NX_SKIN = 1.2; // plastic left between the tapped hole and the top face /* [Switch: slide switch, mounted on top] */ SWITCH_POS = [0, -56]; @@ -128,7 +132,7 @@ HOOK_INSERTS = 7; // +- u HOOK_BASE = [24, 18, 4]; // u, v, Z // Alternative place: the front face (the edge away from you), 2 inserts in // the front wall of the bottom shell; the loop then points forward. -HOOK_FRONT_Z = -19; +HOOK_FRONT_Z = Z_SPLIT - 7; HOOK_MOUNT = "top"; // [top, front] (assembly view only) HOOK_HOLE_D = 8; // for the snap hook HOOK_H = 16; // top of the loop above the top face @@ -138,7 +142,7 @@ HOOK_H = 16; // top of the loop above the top face // hands. Folded forward it wraps the front edge; swung back and down its // crossbar rests against your chest or belly. M3 x 16 button-head screws // with a washer into heat-set inserts in the side walls; friction holds it. -BAIL_PIVOT = [-25, -22]; // v, Z on the side faces (u +-SIDE_U) +BAIL_PIVOT = [-25, Z_BOT + 10]; // v, Z on the side faces (u +-SIDE_U) BAIL_L = 82; // pivot to crossbar centre line BAIL_BOW = 10; // crossbar bows outwards by this much in the middle BAIL_T = 5; // arm thickness (u) @@ -217,8 +221,9 @@ module top_shell() render(convexity = 10) difference() { translate([0, 0, 0.005]) cube(concat(NX_WINDOW, 0.01), center = true); translate([0, 0, NX_BEZEL + 0.01]) cube(concat(NX_WINDOW + [2, 2] * NX_BEZEL, 0.02), center = true); } - translate(concat(NX_WIN - (NX_LCD + [1, 1]) / 2, -PLATE - 1)) cube(concat(NX_LCD + [1, 1], PLATE + 1 - NX_BEZEL)); - nx_holes() translate([0, 0, NX_BOARD_TOP - 1]) cylinder(d = NX_SCREW_D, h = 1 + 4.5); + // LCD pocket: cable allowance on both short sides, so it fits either way round + translate(concat(NX_CENTRE - (NX_LCD + [2 * NX_LCD_CABLE + 0.4, 1]) / 2, -PLATE - 1)) cube(concat(NX_LCD + [2 * NX_LCD_CABLE + 0.4, 1], PLATE + 1 - NX_BEZEL)); + nx_holes() translate([0, 0, NX_BOARD_TOP - 1]) cylinder(d = NX_SCREW_D, h = 1 - NX_BOARD_TOP - NX_SKIN); // joysticks for (s = STICKS) translate([s[0], s[1], -BIG / 2]) cylinder(d = STICK_HOLE_D, h = BIG); stick_screws() translate([0, 0, -BIG / 2]) cylinder(d = STICK_SCREW_D, h = BIG); @@ -450,9 +455,9 @@ module nextion() { translate(concat(-NX_BOARD / 2, 0)) cube(concat(NX_BOARD, 1.6)); for (du = [-1, 1], dv = [-1, 1]) translate([du * NX_HOLES[0], dv * NX_HOLES[1], 0] / 2 + [0, 0, -1]) cylinder(d = 3.2, h = 4); } - translate(concat(NX_WIN - NX_LCD / 2, NX_BOARD_TOP)) color("#202020") cube(concat(NX_LCD, NX_LCD_T)); + translate(concat(NX_CENTRE - NX_LCD / 2, NX_BOARD_TOP)) color("#202020") cube(concat(NX_LCD, NX_LCD_T)); translate(concat(NX_WIN - [73.44, 48.96] / 2, -NX_BEZEL - 0.2)) color("#3050a0") cube([73.44, 48.96, 0.2]); - translate(concat(NX_CENTRE + [(NX_FLIP ? 1 : -1) * (NX_BOARD[0] / 2 - 7), -5], NX_BOARD_TOP - 1.6 - 6)) color("#eee") cube([6, 10, 6]); // J1 4-pin connector (approx.) + translate(concat(NX_CENTRE + [(NX_FLIP ? 1 : -1) * (NX_BOARD[0] / 2 - 7), -5], NX_BOARD_TOP - 1.6 - NX_BACK)) color("#eee") cube([6, 10, NX_BACK]); // J1 4-pin connector (approx.) } module ups_18650() translate(concat(UPS_CENTRE, UPS_Z)) { diff --git a/2026-current/hardware/openscad/stl/remote_v2/remote_v2_top.stl b/2026-current/hardware/openscad/stl/remote_v2/remote_v2_top.stl index cd0a01b..f07ef50 100644 --- a/2026-current/hardware/openscad/stl/remote_v2/remote_v2_top.stl +++ b/2026-current/hardware/openscad/stl/remote_v2/remote_v2_top.stl @@ -1,3 +1,3 @@ version https://git-lfs.github.com/spec/v1 -oid sha256:345e684bfacc6ef5acfd9a56b4c0d640182e962c60bc2eec35f3da153bf55c95 -size 1470383 +oid sha256:c5783f7187630cf76a271597ec6eed83f9a45ace6c9ab777ccf2b756d7fee772 +size 1477686 diff --git a/2026-current/hardware/openscad/stl/remote_v2/remote_v2_top_inlays.3mf b/2026-current/hardware/openscad/stl/remote_v2/remote_v2_top_inlays.3mf index 68592be..c2164c9 100644 --- a/2026-current/hardware/openscad/stl/remote_v2/remote_v2_top_inlays.3mf +++ b/2026-current/hardware/openscad/stl/remote_v2/remote_v2_top_inlays.3mf @@ -1,3 +1,3 @@ version https://git-lfs.github.com/spec/v1 -oid sha256:4fc3c4b612074b280d7909620e55cd0c61a87b9506938942c0e0b9347509dde0 -size 118336 +oid sha256:f8c4d0b92ecde053c2b5db2787b02783f87a14090510fcee459f733b66ed65e5 +size 118469 diff --git a/2026-current/hardware/openscad/stl/remote_v2/remote_v2_top_multicolor.3mf b/2026-current/hardware/openscad/stl/remote_v2/remote_v2_top_multicolor.3mf index cbf8cda..0bd4aee 100644 --- a/2026-current/hardware/openscad/stl/remote_v2/remote_v2_top_multicolor.3mf +++ b/2026-current/hardware/openscad/stl/remote_v2/remote_v2_top_multicolor.3mf @@ -1,3 +1,3 @@ version https://git-lfs.github.com/spec/v1 -oid sha256:a318d6b597bdaf52b3ea7a2fc6fb4e53ac57298315712c14716773c8f84964ba -size 312797 +oid sha256:86e26de613115fbe87ae08f41faae2b2b5a5d348260b8d807da9706f9b4d0be8 +size 313546