2026 remote_v2 case: taller top shell, measured display, M3 display posts

- TOP_GROW: top shell 10 mm taller (room behind the display); the bottom
  shell is unchanged, dependent heights follow Z_SPLIT / Z_BOT.
- Nextion dimensions as measured by the owner: board 100.6 x 55, LCD
  85.7 x 55 x 3.86 plus a 1.3 mm flex cable, 11.21 mm glass to back of J1.
  LCD pocket allows the cable on either short side; bezel 1.0 mm (the
  display sat on the Teensy).
- Display posts tapped M3 for M3 x 5 machine screws, 1.2 mm skin under the
  top face (was M2.5 self-tapping). README screw list and PLANNING.md
  updated; STLs regenerated.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
mangavalkandClaude Opus 5.5 committed 2026-11-17 22:50:48 +01:00
1 parent 2b4750f8f4
commit 3d6c4dd2f0
6 files changed
+32 -26

No files matched your search

+2 -2
View File
@@ -70,8 +70,8 @@ Hardware (besides the electronics of the old remote):
- M3 x 12 x 4 (shells), M3 x 8 button head x 2 (eyelet), M3 x 16 button - M3 x 12 x 4 (shells), M3 x 8 button head x 2 (eyelet), M3 x 16 button
head + washer x 2 (brace), M3 x 8 button head + 7 mm washer x 4 (main head + washer x 2 (brace), M3 x 8 button head + 7 mm washer x 4 (main
board clamps, no holes in the board), M3 x 40 + nut (kickstand pin) board clamps, no holes in the board), M3 x 40 + nut (kickstand pin)
- M2.5 x 14 x 8 (joysticks, into their own boxes), M2.5 self-tapping x 4 - M2.5 x 14 x 8 (joysticks, into their own boxes), M3 x 5 machine screws x 4
(display), M3 self-tapping x 2 (UPS board), M2 self-tapping x 2 (switch) (display, tap the posts M3), M3 self-tapping x 2 (UPS board), M2 self-tapping x 2 (switch)
- Set the Nextion's display direction to 180 in the Nextion Editor: the - Set the Nextion's display direction to 180 in the Nextion Editor: the
display is mounted turned round so its connector clears the Teensy's USB plug. display is mounted turned round so its connector clears the Teensy's USB plug.
+4 -3
View File
@@ -151,7 +151,7 @@ switch's plate sits on top of the case, body through the slot, and the old
8 x 16 slot with d2 holes 19 mm apart fits it exactly; the UPS board's 8 x 16 slot with d2 holes 19 mm apart fits it exactly; the UPS board's
charge/on LEDs show through two slots in the floor. charge/on LEDs show through two slots in the floor.
- Size 216 x 116 x 32 mm (old remote: 208 x 175 x 45). Sticks at u +-80, - Size 216 x 116 x 42 mm (top shell 10 mm taller than first printed, TOP_GROW: room behind the display) (old remote: 208 x 175 x 45). Sticks at u +-80,
display forward of them, strap eyelet behind the display, UPS board behind display forward of them, strap eyelet behind the display, UPS board behind
that, switch at the rear centre. Main board under the display. that, switch at the rear centre. Main board under the display.
- JH-D300X-R1: dust cover d53.5 on the top face; the 40.4 mm control box - JH-D300X-R1: dust cover d53.5 on the top face; the 40.4 mm control box
@@ -160,8 +160,9 @@ charge/on LEDs show through two slots in the floor.
towards the middle and towards the user. towards the middle and towards the user.
- Display mounted turned 180 deg so its J1 connector is on the right, clear - Display mounted turned 180 deg so its J1 connector is on the right, clear
of the Teensy's USB plug: set display direction 180 in the Nextion Editor. of the Teensy's USB plug: set display direction 180 in the Nextion Editor.
Glass 1.5 mm under the top face, board on 4 posts (M2.5 self-tapping); Glass 1.0 mm under the top face, board on 4 posts tapped M3 (3.66 mm of thread, 1.2 mm under the top face);
the LCD thickness (4.5) is a guess. LCD 85.7 x 55 x 3.86 plus a 1.3 mm flex cable on one side, 11.21 mm glass to
back of J1 (owner measured).
- Main board clamped at 4 points on its long sides, no holes in the board - Main board clamped at 4 points on its long sides, no holes in the board
(owner): posts beside the edges carry it, M3 x 8 button heads with d7 (owner): posts beside the edges carry it, M3 x 8 button heads with d7
washers in heat-set inserts clamp the edge. 2 mm above the kickstand washers in heat-set inserts clamp the edge. 2 mm above the kickstand
+20 -15
View File
@@ -27,8 +27,9 @@
/* [Shell] */ /* [Shell] */
T = 2.4; // walls and floor (6 perimeters of 0.4) T = 2.4; // walls and floor (6 perimeters of 0.4)
PLATE = 3.0; // top plate PLATE = 3.0; // top plate
Z_BOT = -32; // flat underside (32 mm thick: the D300X sticks reach 28.5 down) TOP_GROW = 10; // extra height of the top shell only (room behind the display); the bottom shell is unchanged
Z_SPLIT = -12; // top shell / bottom shell Z_BOT = -32 - TOP_GROW; // flat underside (32 mm thick before TOP_GROW: the D300X sticks reach 28.5 down)
Z_SPLIT = -12 - TOP_GROW; // top shell / bottom shell
CHAMFER = 4; // 45 deg bottom edge (printable without support) CHAMFER = 4; // 45 deg bottom edge (printable without support)
TOP_CHAMFER = 1.5; // 45 deg top edge (the top shell prints face down) TOP_CHAMFER = 1.5; // 45 deg top edge (the top shell prints face down)
LIP_H = 2.5; // locating lip on the bottom shell, into the top shell LIP_H = 2.5; // locating lip on the bottom shell, into the top shell
@@ -53,7 +54,7 @@ INSERT_D = 4.0;
INSERT_L = 6; INSERT_L = 6;
SCREW_D = 3.4; SCREW_D = 3.4;
HEAD_D = 6.5; HEAD_D = 6.5;
HEAD_Z = -19; // counterbore floor: 7 mm of tower + 5 mm into the insert HEAD_Z = Z_SPLIT - 7; // counterbore floor: 7 mm of tower + 5 mm into the insert
/* [Joysticks] */ /* [Joysticks] */
STICK_HOLE_D = 40; STICK_HOLE_D = 40;
@@ -61,18 +62,21 @@ STICK_SCREW = 16.25; // 4 x M2.5 x 14 on a 32.5 mm square, through cover and
STICK_SCREW_D = 2.8; STICK_SCREW_D = 2.8;
/* [Display: Nextion NX4832T035] */ /* [Display: Nextion NX4832T035] */
NX_BOARD = [100.5, 54.94]; NX_BOARD = [100.6, 55]; // measured by the owner
NX_HOLES = [94.2, 48.5]; // M3 grid, centred on the board NX_HOLES = [94.2, 48.5]; // M3 grid, centred on the board
NX_CENTRE = [0, 20]; // board centre (forward of the sticks, so the strap misses it) NX_CENTRE = [0, 20]; // board centre (forward of the sticks, so the strap misses it)
NX_FLIP = true; // display mounted turned 180 deg (its J1 connector on the right, clear of NX_FLIP = true; // display mounted turned 180 deg (its J1 connector on the right, clear of
// the Teensy's USB plug): set display direction 180 in the Nextion Editor // the Teensy's USB plug): set display direction 180 in the Nextion Editor
NX_WIN_OFF = [NX_FLIP ? 2.15 : -2.15, 0]; // window (visible area) centre from the board centre NX_WIN_OFF = [NX_FLIP ? 2.15 : -2.15, 0]; // window (visible area) centre from the board centre
NX_WINDOW = [75.9, 50.9]; // opening in the plate NX_WINDOW = [75.9, 50.9]; // opening in the plate
NX_LCD = [84, 54]; // LCD module outline NX_LCD = [85.7, 55]; // LCD module outline (owner: 7.45 mm of board beside it on both sides, centred on the board)
NX_LCD_T = 4.5; // LCD thickness: approximate, measure before printing NX_LCD_CABLE = 1.3; // its flex cable sticks out this much on one short side (87 mm overall)
NX_BEZEL = 1.5; // plate left above the glass NX_LCD_T = 3.86; // LCD thickness (owner)
NX_POST_D = 5.5; // clears the LCD module by 0.2 mm NX_BACK = 11.21 - NX_LCD_T - 1.6; // board underside to back of the J1 connector (owner: 11.21 from the glass)
NX_SCREW_D = 2.2; // M2.5 self-tapping through the board NX_BEZEL = 1.0; // plate left above the glass (was 1.5: the display sat on the Teensy)
NX_POST_D = 5.5; // clears the LCD module (with its cable) by 0.2 mm
NX_SCREW_D = 2.5; // M3 tap drill: tap the posts for M3 x 5 machine screws through the board
NX_SKIN = 1.2; // plastic left between the tapped hole and the top face
/* [Switch: slide switch, mounted on top] */ /* [Switch: slide switch, mounted on top] */
SWITCH_POS = [0, -56]; SWITCH_POS = [0, -56];
@@ -128,7 +132,7 @@ HOOK_INSERTS = 7; // +- u
HOOK_BASE = [24, 18, 4]; // u, v, Z HOOK_BASE = [24, 18, 4]; // u, v, Z
// Alternative place: the front face (the edge away from you), 2 inserts in // Alternative place: the front face (the edge away from you), 2 inserts in
// the front wall of the bottom shell; the loop then points forward. // the front wall of the bottom shell; the loop then points forward.
HOOK_FRONT_Z = -19; HOOK_FRONT_Z = Z_SPLIT - 7;
HOOK_MOUNT = "top"; // [top, front] (assembly view only) HOOK_MOUNT = "top"; // [top, front] (assembly view only)
HOOK_HOLE_D = 8; // for the snap hook HOOK_HOLE_D = 8; // for the snap hook
HOOK_H = 16; // top of the loop above the top face HOOK_H = 16; // top of the loop above the top face
@@ -138,7 +142,7 @@ HOOK_H = 16; // top of the loop above the top face
// hands. Folded forward it wraps the front edge; swung back and down its // hands. Folded forward it wraps the front edge; swung back and down its
// crossbar rests against your chest or belly. M3 x 16 button-head screws // crossbar rests against your chest or belly. M3 x 16 button-head screws
// with a washer into heat-set inserts in the side walls; friction holds it. // with a washer into heat-set inserts in the side walls; friction holds it.
BAIL_PIVOT = [-25, -22]; // v, Z on the side faces (u +-SIDE_U) BAIL_PIVOT = [-25, Z_BOT + 10]; // v, Z on the side faces (u +-SIDE_U)
BAIL_L = 82; // pivot to crossbar centre line BAIL_L = 82; // pivot to crossbar centre line
BAIL_BOW = 10; // crossbar bows outwards by this much in the middle BAIL_BOW = 10; // crossbar bows outwards by this much in the middle
BAIL_T = 5; // arm thickness (u) BAIL_T = 5; // arm thickness (u)
@@ -217,8 +221,9 @@ module top_shell() render(convexity = 10) difference() {
translate([0, 0, 0.005]) cube(concat(NX_WINDOW, 0.01), center = true); translate([0, 0, 0.005]) cube(concat(NX_WINDOW, 0.01), center = true);
translate([0, 0, NX_BEZEL + 0.01]) cube(concat(NX_WINDOW + [2, 2] * NX_BEZEL, 0.02), center = true); translate([0, 0, NX_BEZEL + 0.01]) cube(concat(NX_WINDOW + [2, 2] * NX_BEZEL, 0.02), center = true);
} }
translate(concat(NX_WIN - (NX_LCD + [1, 1]) / 2, -PLATE - 1)) cube(concat(NX_LCD + [1, 1], PLATE + 1 - NX_BEZEL)); // LCD pocket: cable allowance on both short sides, so it fits either way round
nx_holes() translate([0, 0, NX_BOARD_TOP - 1]) cylinder(d = NX_SCREW_D, h = 1 + 4.5); translate(concat(NX_CENTRE - (NX_LCD + [2 * NX_LCD_CABLE + 0.4, 1]) / 2, -PLATE - 1)) cube(concat(NX_LCD + [2 * NX_LCD_CABLE + 0.4, 1], PLATE + 1 - NX_BEZEL));
nx_holes() translate([0, 0, NX_BOARD_TOP - 1]) cylinder(d = NX_SCREW_D, h = 1 - NX_BOARD_TOP - NX_SKIN);
// joysticks // joysticks
for (s = STICKS) translate([s[0], s[1], -BIG / 2]) cylinder(d = STICK_HOLE_D, h = BIG); for (s = STICKS) translate([s[0], s[1], -BIG / 2]) cylinder(d = STICK_HOLE_D, h = BIG);
stick_screws() translate([0, 0, -BIG / 2]) cylinder(d = STICK_SCREW_D, h = BIG); stick_screws() translate([0, 0, -BIG / 2]) cylinder(d = STICK_SCREW_D, h = BIG);
@@ -450,9 +455,9 @@ module nextion() {
translate(concat(-NX_BOARD / 2, 0)) cube(concat(NX_BOARD, 1.6)); translate(concat(-NX_BOARD / 2, 0)) cube(concat(NX_BOARD, 1.6));
for (du = [-1, 1], dv = [-1, 1]) translate([du * NX_HOLES[0], dv * NX_HOLES[1], 0] / 2 + [0, 0, -1]) cylinder(d = 3.2, h = 4); for (du = [-1, 1], dv = [-1, 1]) translate([du * NX_HOLES[0], dv * NX_HOLES[1], 0] / 2 + [0, 0, -1]) cylinder(d = 3.2, h = 4);
} }
translate(concat(NX_WIN - NX_LCD / 2, NX_BOARD_TOP)) color("#202020") cube(concat(NX_LCD, NX_LCD_T)); translate(concat(NX_CENTRE - NX_LCD / 2, NX_BOARD_TOP)) color("#202020") cube(concat(NX_LCD, NX_LCD_T));
translate(concat(NX_WIN - [73.44, 48.96] / 2, -NX_BEZEL - 0.2)) color("#3050a0") cube([73.44, 48.96, 0.2]); translate(concat(NX_WIN - [73.44, 48.96] / 2, -NX_BEZEL - 0.2)) color("#3050a0") cube([73.44, 48.96, 0.2]);
translate(concat(NX_CENTRE + [(NX_FLIP ? 1 : -1) * (NX_BOARD[0] / 2 - 7), -5], NX_BOARD_TOP - 1.6 - 6)) color("#eee") cube([6, 10, 6]); // J1 4-pin connector (approx.) translate(concat(NX_CENTRE + [(NX_FLIP ? 1 : -1) * (NX_BOARD[0] / 2 - 7), -5], NX_BOARD_TOP - 1.6 - NX_BACK)) color("#eee") cube([6, 10, NX_BACK]); // J1 4-pin connector (approx.)
} }
module ups_18650() translate(concat(UPS_CENTRE, UPS_Z)) { module ups_18650() translate(concat(UPS_CENTRE, UPS_Z)) {