2026-09-28 18:14:00 +02:00
# Hexapod
2026-10-01 15:53:55 +02:00
A six-legged walking robot (Teensy 3.6) and its handheld remote
2026-11-14 12:19:16 +01:00
(Teensy 4.0 + Nextion touchscreen), linked over nRF24L01.
2026-09-28 18:14:00 +02:00
2026-11-14 12:14:32 +01:00

2026-11-14 18:57:49 +01:00

The remote above is the new design (`hardware/openscad/remote_v2.scad` , not
printed yet). The original printed remote is on the
[archive page ](hardware/openscad/ARCHIVE.md ).
2026-11-14 12:14:32 +01:00
2026-09-28 18:14:00 +02:00
```
2026-09-29 00:37:12 +02:00
robot/ robot firmware: IK, gait, body pose, IMU stabilization, state machine
remote/ remote firmware: 2 x 3-axis sticks, MPU6050 tilt, Nextion UI, RF24 TX
shared/ HexapodProtocol: the CmdPacket wire format + radio settings used by both
sim/ the unchanged robot firmware compiled into a DLL for the simulation
Hexapod_Simulation_Unity/ Unity project that runs that DLL on the 3D model
2026-11-14 18:57:49 +01:00
hardware/openscad/ OpenSCAD model of the robot (rebuilt from the Fusion designs) and the new remote
hardware/openscad/stl/ print-ready STL exports
2026-10-25 17:30:35 +01:00
hardware/fusion360/ Fusion 360 designs: body, legs, servo, servo horn, remote case
2026-09-29 00:37:12 +02:00
scripts/ PlatformIO helper (per-environment sketch folder)
2026-09-28 18:14:00 +02:00
```
2026-10-25 17:30:35 +01:00
This is the `2026-current/` folder of the hexapod-robot repo; the earlier
generations (2009 onwards) are in the folders next to it, see
[../README.md ](../README.md ).
2026-09-28 18:14:00 +02:00
## Build (PlatformIO)
```
pio run # build both
pio run -e robot -t upload
pio run -e remote -t upload
pio device monitor -e robot
```
2026-09-29 00:37:12 +02:00
## Simulation
2026-10-25 17:30:35 +01:00
From this `2026-current` folder in PowerShell (the dev PC is Windows):
2026-09-29 00:37:12 +02:00
```
.\sim\build.ps1 # build hexapod_sim.dll + run the headless firmware checks
```
Then open `Hexapod_Simulation_Unity` and press Play. See
[sim/README.md ](sim/README.md ).
2026-11-14 18:57:49 +01:00
## Printing the remote (v2)
STLs in [hardware/openscad/stl/remote_v2/ ](hardware/openscad/stl/remote_v2/ ),
already in print orientation; everything prints in ASA without supports.
Regenerate them from `remote_v2.scad` with `-D 'PART="..."'` .
| File | Part | Notes |
|------|------|-------|
| `remote_v2_top_multicolor.3mf` | top shell with both inlays | One object with three parts on filaments 1/2/3: case black, honeycomb red, ON/OFF white. The inlays are the first 3 layers (0.6 mm) of the face-down shell, so the colour swaps only happen there. Made by `hardware/openscad/export_3mf.py` from the three STLs below |
| `remote_v2_top.stl` + `_inlay.stl` + `_text.stl` | the same, as STLs | Load the three at once and keep them as one multi-part object |
| `remote_v2_bottom.stl` | bottom shell | flat underside on the bed |
| `remote_v2_kickstand.stl` | table stand | |
| `remote_v2_eyelet.stl` | neck-strap eyelet | on the top face (slots to balance it) or on the front edge |
| `remote_v2_bail.stl` | body brace | swings down and back to rest against your body |
Hardware (besides the electronics of the old remote):
- 14 x M3 heat-set inserts (4.0 mm hole, ~5.7 mm long): 4 shell screws,
2 + 2 eyelet (top and front), 2 brace pivots, 4 main-board clamps
- M3 x 12 x 4 (shells), M3 x 8 button head x 2 (eyelet), M3 x 16 button
head + washer x 2 (brace), M3 x 8 button head + 7 mm washer x 4 (main
board clamps, no holes in the board), M3 x 40 + nut (kickstand pin)
- M2.5 x 14 x 8 (joysticks, into their own boxes), M2.5 self-tapping x 4
(display), M3 self-tapping x 2 (UPS board), M2 self-tapping x 2 (switch)
- Set the Nextion's display direction to 180 in the Nextion Editor: the
display is mounted turned round so its connector clears the Teensy's USB plug.
Design notes, checks and open points: [hardware/openscad/PLANNING.md ](hardware/openscad/PLANNING.md ).
2026-09-28 18:14:00 +02:00
## Where to go next
- **[robot/README.md ](robot/README.md )**: placeholder geometry to measure,
the bench-check checklist, and the serial test harness for driving the
robot without a remote.
- **[remote/README.md ](remote/README.md )**: wiring, control scheme, stick
calibration, and the remote's serial console.
- **[remote/NEXTION.md ](remote/NEXTION.md )**: how to build the touchscreen
HMI.
- **[shared/HexapodProtocol/HexapodProtocol.h ](shared/HexapodProtocol/HexapodProtocol.h )**:
the protocol. Change it only by reflashing both boards.