Public Access
92 lines
3.3 KiB
Markdown
92 lines
3.3 KiB
Markdown
 
|
# Planar EL512.256-H on ESP32
|
|||
|
|
|
|||
|
|
Drive a Planar EL512.256-H (512 × 256, monochrome electroluminescent) panel from an
|
|||
|
|
ESP-WROOM-32 (classic ESP32), with an [Adafruit GFX](https://github.com/adafruit/Adafruit-GFX-Library)
|
|||
|
|
compatible driver so the usual drawing, text and font APIs work.
|
|||
|
|
|
|||
|
|
The panel has no frame memory and needs a continuous video stream. The ESP32's I2S0
|
|||
|
|
peripheral in 8-bit parallel (LCD) mode streams a precomputed frame from DMA, so the
|
|||
|
|
CPU is free while the panel refreshes.
|
|||
|
|
|
|||
|
|
**Status:** project skeleton. Framebuffer, GFX layer and row encoder are in place; the
|
|||
|
|
I2S/DMA start-up (`EL512Panel::startI2S()`) is still a stub.
|
|||
|
|
|
|||
|
|
## Hardware
|
|||
|
|
|
|||
|
|
- ESP-WROOM-32 dev board (`esp32dev`)
|
|||
|
|
- Planar EL512.256-H, configured for **two-bit parallel mode** (mode jumper OFF, see datasheet)
|
|||
|
|
- Datasheet: [docs/datasheet/EL512.256-H3 FRB.pdf](docs/datasheet/EL512.256-H3%20FRB.pdf)
|
|||
|
|
- Check the panel's logic-level and supply requirements in the datasheet before wiring.
|
|||
|
|
|
|||
|
|
## Wiring
|
|||
|
|
|
|||
|
|
| Panel signal | Function | ESP32 GPIO | DMA byte bit |
|
|||
|
|
|--------------|-----------------------------------------|-----------:|-------------:|
|
|||
|
|
| VCLK | Video clock (rising edge) | 18 | I2S clock |
|
|||
|
|
| VID | Pixel data, even columns | 19 | 0 |
|
|||
|
|
| TVID | Pixel data, odd columns (two-bit mode) | 21 | 1 |
|
|||
|
|
| HS | Horizontal sync | 22 | 2 |
|
|||
|
|
| VS | Vertical sync | 23 | 3 |
|
|||
|
|
| ENABLE | Display enable | 25 | — |
|
|||
|
|
| _LOWPWR | Low-power mode (active low) | 26 | — |
|
|||
|
|
| GND | Ground | GND | — |
|
|||
|
|
|
|||
|
|
The pin map lives in [include/pins.h](include/pins.h).
|
|||
|
|
|
|||
|
|
## Timing
|
|||
|
|
|
|||
|
|
| Parameter | Value |
|
|||
|
|
|----------------------|-----------------------------------------|
|
|||
|
|
| Pixel clock (VCLK) | 5 MHz, 2 pixels per clock |
|
|||
|
|
| Clocks per row | 272 (256 data + 16 blanking) |
|
|||
|
|
| Lines per frame | 261 (256 visible + 5 blanking) |
|
|||
|
|
| Refresh | 5 MHz / (272 × 261) ≈ 70.4 Hz |
|
|||
|
|
|
|||
|
|
## Layout
|
|||
|
|
|
|||
|
|
```
|
|||
|
|
platformio.ini build config (esp32dev, Arduino, Adafruit GFX)
|
|||
|
|
include/pins.h pin map
|
|||
|
|
src/main.cpp test sketch: test pattern + text
|
|||
|
|
lib/EL512/ local library
|
|||
|
|
src/EL512Panel.* framebuffer, row encoder, I2S DMA refresh (stub)
|
|||
|
|
src/EL512_GFX.* Adafruit_GFX subclass
|
|||
|
|
test/ unit tests (placeholder)
|
|||
|
|
docs/ datasheet and notes
|
|||
|
|
```
|
|||
|
|
|
|||
|
|
## Build and flash
|
|||
|
|
|
|||
|
|
Requires [PlatformIO](https://platformio.org/) (CLI or the VS Code extension).
|
|||
|
|
|
|||
|
|
```bash
|
|||
|
|
pio run
|
|||
|
|
```
|
|||
|
|
|
|||
|
|
```bash
|
|||
|
|
pio run -t upload
|
|||
|
|
```
|
|||
|
|
|
|||
|
|
```bash
|
|||
|
|
pio device monitor
|
|||
|
|
```
|
|||
|
|
|
|||
|
|
## Using the driver
|
|||
|
|
|
|||
|
|
```cpp
|
|||
|
|
#include <EL512.h>
|
|||
|
|
#include "pins.h"
|
|||
|
|
|
|||
|
|
EL512Panel panel({el512pins::VCLK, el512pins::VID, el512pins::TVID, el512pins::HS,
|
|||
|
|
el512pins::VS, el512pins::ENABLE, el512pins::LOWPWR_N});
|
|||
|
|
EL512_GFX display(panel);
|
|||
|
|
|
|||
|
|
void setup() {
|
|||
|
|
display.begin();
|
|||
|
|
display.setTextColor(1);
|
|||
|
|
display.print("Hello");
|
|||
|
|
display.display(); // push the drawing buffer to the refresh stream
|
|||
|
|
}
|
|||
|
|
```
|
|||
|
|
|
|||
|
|
See [docs/README.md](docs/README.md) for design notes and the plan.
|