Notes: idea of custom firmware on the display, and the bricking risk
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
85422a1ef4
commit
7bb102676b
1 file changed
+34
@@ -232,3 +232,37 @@ Samples waiting to be compiled: `g3.json` in the session scratchpad (directions
|
|||||||
`>=`, mixed `&&`/`||`, string attributes, negative globals, more variants) -- regenerate with
|
`>=`, mixed `&&`/`||`, string attributes, negative globals, more variants) -- regenerate with
|
||||||
`tools/make_tft_samples.py` (`direction` and `gradient` keys) if the scratchpad is gone.
|
`tools/make_tft_samples.py` (`direction` and `gradient` keys) if the scratchpad is gone.
|
||||||
New sample pairs live in `D:\Claude\nextion-tft-samples\2026-11-17` (outside the repo).
|
New sample pairs live in `D:\Claude\nextion-tft-samples\2026-11-17` (outside the repo).
|
||||||
|
|
||||||
|
## Idea: custom firmware on the display, and the risk of bricking it (2026-11-17)
|
||||||
|
|
||||||
|
Only an idea, not planned. Nothing here was tested; the chips on the board have not been
|
||||||
|
identified (a photo of the back of the board would tell us the MCU, display controller, flash
|
||||||
|
and whether there are SWD/JTAG pads).
|
||||||
|
|
||||||
|
Three ways to get our own code onto the screen, from safest to riskiest:
|
||||||
|
|
||||||
|
1. **A `.tft` from our builder, uploaded the normal way (serial or microSD): low risk.** The
|
||||||
|
builder copies Nextion's firmware pieces unchanged (the SHA-256 check guarantees that). Only
|
||||||
|
the project data is ours. A mistake there should give a blank or garbled screen, a crash loop or
|
||||||
|
a refused upload, not a dead update path. The usual recovery is a microSD card with a
|
||||||
|
known-good Editor-made `.tft` (insert, power on). Caveat: which flash areas the firmware pieces
|
||||||
|
overwrite is unknown, but since they are the Editor's own bytes the risk equals any Editor
|
||||||
|
upload. Before the first test on a real display: prepare that recovery card, and start with a
|
||||||
|
builder output that is byte-identical to the Editor's.
|
||||||
|
2. **Our own firmware flashed over SWD (like the nRF dongle): the Nextion firmware is lost for
|
||||||
|
good, the hardware survives.** The chip is almost certainly read-protected, so the original
|
||||||
|
cannot be backed up. The chip itself is hard to brick through SWD: it can almost always be
|
||||||
|
reflashed. Exceptions: firmware that disables the debug pins (usually recoverable by connecting
|
||||||
|
under reset) and setting the permanent read-protection level (irreversible). Small hardware
|
||||||
|
risk: driving a pin against something on the board, or misconfiguring the backlight / LCD
|
||||||
|
supply. Read the board layout before writing to pins. Then own drivers are needed for the LCD
|
||||||
|
controller, the touch input, the flash and the UART, after which LVGL could run on it. Feasible
|
||||||
|
on a common STM32/GD32-class MCU with enough RAM; much harder with a proprietary or FPGA
|
||||||
|
display controller. Only on a spare display.
|
||||||
|
3. **Our own code in the firmware slots of a `.tft`: highest risk, far away.** Broken code there
|
||||||
|
could stop the display from ever accepting a new upload; whether microSD recovery still works
|
||||||
|
depends on where the bootloader lives (unknown). It would also need Nextion's runtime and
|
||||||
|
bootloader to be understood, which goes beyond the black-box rule.
|
||||||
|
|
||||||
|
Cheaper alternative if the goal is just "our own code on the remote's screen": an ESP32 board with
|
||||||
|
a 3.5" 480x320 touchscreen costs about the same, is fully open, runs LVGL and has Wi-Fi/Bluetooth.
|
||||||
Reference in new issue
Block a user