dglaude
9b2cb53f09
diff_ignore could be used to ignore some file from a recursive diff. acinclude.m4 and Makefile.am are for CwLinux driver.
537 lines
12 KiB
Plaintext
537 lines
12 KiB
Plaintext
# LCDd.conf
|
|
#
|
|
# This file contains the configuration for the LCDd server.
|
|
#
|
|
# The format is ini-file-like. It is divided into sections that start at
|
|
# markers that look like [section]. Comments are all line-based comments,
|
|
# and are lines that start with '#' or ';'.
|
|
#
|
|
# The server has a 'central' section named [server]. For the menu there is
|
|
# a section called [menu]. Further each driver has a section which
|
|
# defines how the driver acts.
|
|
#
|
|
# The drivers are activated by specifiying them in a driver= line in the
|
|
# server section, like:
|
|
#
|
|
# Driver=curses
|
|
#
|
|
# This tells LCDd to use the curses driver.
|
|
# The first driver that is loaded and is capable of output defines the
|
|
# size of the display. The default driver to use is curses.
|
|
# If -d is specified on the command line, the Driver= options in the
|
|
# config file are ignored.
|
|
#
|
|
# The drivers can read their own options from the config file, but some of
|
|
# them don't do this yet. They expect 'command-line'-format parameters that
|
|
# were previously placed on the command line. These parameters can be
|
|
# given to the driver in the following way:
|
|
#
|
|
# Arguments="place arguments here"
|
|
#
|
|
# The arguments between the quotes are passed to the driver.
|
|
# As said before these are the same arguments that the driver would have
|
|
# been passed under the old command line format of
|
|
#
|
|
# -d <driver> "<driverargs>"
|
|
#
|
|
# Note that the -d option still works, but not allows driverargs anymore.
|
|
|
|
|
|
[server]
|
|
# Server section with all kinds of settings for the LCDd server
|
|
|
|
Driver=curses
|
|
#Driver=hd44780
|
|
#Driver=MtxOrb
|
|
#Driver=CFontz633
|
|
#Driver=CwLnx
|
|
#
|
|
# Tells the server to load the given drivers. Multiple lines can be given.
|
|
# The name of the driver is exactly the same as the name of the driver
|
|
# module that is to be loaded, including the case of the letters !
|
|
# (That is: unless a file= option is given in the driver section)
|
|
|
|
Bind=127.0.0.1
|
|
# Tells the driver to bind to the given interface
|
|
|
|
Port=13666
|
|
# Listen on this specified port; defaults to 13666.
|
|
|
|
#ReportLevel=3
|
|
# Sets the reporting level; defaults to 2 (warnings and errors only).
|
|
|
|
#ReportToSyslog=yes
|
|
# Should we report to syslog instead of stderr ? Default: no
|
|
|
|
WaitTime=5
|
|
# Sets the default time in seconds to displays a screen.
|
|
|
|
User=nobody
|
|
# User to run as. LCDd will drop its root priviledges,
|
|
# if any, and run as this user instead.
|
|
|
|
#ServerScreen=no
|
|
# If yes, the the serverscreen will be rotated as a usual info screen. If no,
|
|
# it will be a background screen, only visible when no other screens are
|
|
# active.
|
|
|
|
#Foreground=no
|
|
# The server will stay in the foreground if set to true.
|
|
|
|
DriverPath=server/drivers/
|
|
# Where can we find the driver modules ?
|
|
# Always place a slash as last character !
|
|
|
|
# The "...Key=" lines define what the server does with keypresses that
|
|
# don't go to any client.
|
|
# These are the defaults:
|
|
ToggleRotateKey=Enter
|
|
PrevScreenKey=Left
|
|
NextScreenKey=Right
|
|
#ScrollUpKey=Up
|
|
#ScrollDownKey=Down
|
|
|
|
# If you have only 4 keys, you can choose to use this:
|
|
#ToggleRotateKey=Enter
|
|
#PrevScreenKey=Up
|
|
#NextScreenKey=Down
|
|
|
|
# If you have only 3 keys, you can choose to use this:
|
|
#ToggleRotateKey=Enter
|
|
#PrevScreenKey=Up
|
|
|
|
|
|
|
|
[menu]
|
|
# The menu section. The menu is an internal LCDproc client.
|
|
# You can configure what keys the menu should use. Note that only the menukey
|
|
# will be reserved exclusively, the others in shared mode.
|
|
|
|
# The following works excelent with 4 keys or more.
|
|
MenuKey=Escape
|
|
EnterKey=Enter
|
|
UpKey=Up
|
|
DownKey=Down
|
|
|
|
# If you have only 3 keys, you could use something like this:
|
|
#MenuKey=Escape
|
|
#EnterKey=Enter
|
|
#DownKey=Down
|
|
|
|
|
|
# Driver sections are below this line, in alphabetical order
|
|
|
|
|
|
[bayrad]
|
|
# EMAC BayRAD driver
|
|
|
|
Arguments="fill in here"
|
|
|
|
# -d --device Select the output device to use [/dev/lcd]
|
|
# -t --type Select the LCD type (size) [20x2]
|
|
# -s --speed Set the communication speed [19200]
|
|
# -h --help Show this help information
|
|
|
|
|
|
|
|
[CFontz]
|
|
# CrystalFontz driver
|
|
# Use this driver for CF632 and CF634.
|
|
|
|
# Select the output device to use [/dev/lcd]
|
|
Device=/dev/ttyS0
|
|
# Select the LCD type (size) [20x4]
|
|
Size=20x4
|
|
# Set the initial contrast [140]
|
|
Contrast=140
|
|
# Set the initial brightness [255]
|
|
Brightness=255
|
|
# Set the initial off-brightness [0]
|
|
# This value is used when the display is normally
|
|
# switched off in case LCDd is inactive
|
|
OffBrightness=0
|
|
# Set the communication speed [9600]
|
|
# possible values: 1200, 2400, 9600
|
|
Speed=9600
|
|
# Set the firmware version (New means >= 2.0) [no]
|
|
NewFirmware=no
|
|
# Reinitialize the LCD's BIOS [no]
|
|
# normally you shouldn't need this
|
|
Reboot=no
|
|
|
|
|
|
[CFontz633]
|
|
# CrystalFontz633 driver
|
|
# Use this driver only for CF633.
|
|
|
|
# Select the output device to use [/dev/lcd]
|
|
Device=/dev/ttyS0
|
|
# Select the LCD type (size) [20x4]
|
|
Size=16x2
|
|
# Set the initial contrast [140]
|
|
Contrast=140
|
|
# Set the initial brightness [100]
|
|
# Brightness hardware value is between 0 and 100.
|
|
Brightness=100
|
|
# Set the initial off-brightness [0]
|
|
# This value is used when the display is normally
|
|
# switched off in case LCDd is inactive
|
|
OffBrightness=50
|
|
# Set the communication speed [9600]
|
|
# possible values: 19200
|
|
Speed=19200
|
|
# Set the firmware version (New means >= 2.0) [no]
|
|
# Currently this flag is not in use, there is no such thing as NewFirmware. ;=)
|
|
NewFirmware=no
|
|
# Reinitialize the LCD's BIOS [no]
|
|
# I want to reboot the LCD to make sure we start from a known state
|
|
Reboot=yes
|
|
|
|
|
|
[curses]
|
|
# Curses driver
|
|
|
|
# color settings
|
|
# foreground color [blue]
|
|
foreground=blue
|
|
# background color [cyan]
|
|
background=cyan
|
|
# backlight color [red]
|
|
backlight=red
|
|
|
|
# display size [20x4]
|
|
size=20x4
|
|
|
|
# What position (X,Y) to start the left top corner at...
|
|
# Default: (7,7)
|
|
topleftx=7
|
|
toplefty=7
|
|
|
|
[CwLnx]
|
|
# Cwlinux driver
|
|
|
|
# Select the output device to use [/dev/lcd]
|
|
#Device=/dev/ttyS0
|
|
Device=/dev/ttyUSB0
|
|
|
|
# Select the LCD type (size) [20x4]
|
|
Size=20x4
|
|
|
|
# Set the communication speed [9600]
|
|
# possible values: 9600, 19200
|
|
Speed=19200
|
|
|
|
# Reinitialize the LCD's BIOS [no]
|
|
# normally you shouldn't need this
|
|
Reboot=no
|
|
|
|
# If you have a keypad connected. Keypad layout is currently not
|
|
# configureable from the config file.
|
|
Keypad=yes
|
|
|
|
# If you have a non standard keypad you can associate any keystrings to keys.
|
|
# There are 6 input key in the CwLnx hardware that generate caracter
|
|
# from 'A' to 'F'.
|
|
#
|
|
# The following it the build in default mapping hardcoded in the driver.
|
|
# You can leave those unchanged if you have a standard keypad.
|
|
# You can change it if you want to report other keystrings or have a non
|
|
# standard keypad.
|
|
|
|
# KeyMap_A=Up
|
|
# KeyMap_B=Down
|
|
# KeyMap_C=Left
|
|
# KeyMap_D=Right
|
|
# KeyMap_E=Enter
|
|
# KeyMap_F=Escape
|
|
|
|
# keypad_test_mode permit to test keypad assignement
|
|
# Default value is no
|
|
#keypad_test_mode=yes
|
|
|
|
|
|
[glk]
|
|
# Matrix Orbital GLK driver
|
|
|
|
Arguments="-d /dev/ttyS0 -s 9600"
|
|
|
|
# -d, --device select the serial device to use [/dev/lcd]
|
|
# -c, --contrast set the initial contrast value [140]
|
|
# -s, --speed set the serial port speed [19200]
|
|
# -h, --help display this help text
|
|
|
|
|
|
|
|
[hd44780]
|
|
# Hitachi HD44780 driver
|
|
|
|
Port=0x378
|
|
# Port where the LPT is. Usual values are 0x278, 0x378 and 0x3BC
|
|
|
|
ConnectionType=4bit
|
|
# Select what type of connection. See documentation for types.
|
|
|
|
Keypad=no
|
|
# If you have a keypad connected.
|
|
# You may also need to configure the keypad layout further on in this file.
|
|
|
|
Backlight=no
|
|
# If you have a switchable backlight.
|
|
|
|
Outputport=no
|
|
# If you have the additional output port ("bargraph") and you want to
|
|
# be able to control it with the lcdproc OUTPUT command
|
|
|
|
Size=20x4
|
|
# Specifies the size of the LCD.
|
|
# In case of multiple combined displays, this should be the total size.
|
|
|
|
#vspan=1,2
|
|
# For multiple displays: at what 'logical' lines do the individual displays
|
|
# start.
|
|
|
|
#extended=yes
|
|
# If you want to use more than 3 HD44780 controllers on the LPT, you need to
|
|
# specify this. See documentation.
|
|
|
|
#DelayMult=2
|
|
# If your display is slow and cannot keep up with the flow of data from
|
|
# LCDd, garbage can appear on the LCDd. Set this delay factor to 2 or 4
|
|
# to increase the delays. Default: 1.
|
|
|
|
DelayBus=true
|
|
# You can reduce the inserted delays by setting this to false.
|
|
# On fast PCs it is possible your LCD does not respond correctly.
|
|
# Default: true.
|
|
|
|
# If you have a keypad you can assign keystrings to the keys.
|
|
# See documentation for used terms and how to wire it.
|
|
# For example to give directly connected key 4 the string "Enter", use:
|
|
# KeyDirect_4=Enter
|
|
# For matrix keys use the X and Y coordinates of the key:
|
|
# KeyMatrix_1_3=Enter
|
|
|
|
KeyMatrix_4_1=Enter
|
|
KeyMatrix_4_2=Up
|
|
KeyMatrix_4_3=Down
|
|
KeyMatrix_4_4=Escape
|
|
|
|
|
|
[IrMan]
|
|
#IrMan driver
|
|
#if in trouble with IrMan, try Lirc emulator for IrMan
|
|
|
|
Arguments="fill in here"
|
|
|
|
# -d --device Select the input device to use
|
|
# -c --config Select the configuration file to use
|
|
# -h --help Show this help information
|
|
|
|
|
|
|
|
[joy]
|
|
# Joystick driver
|
|
|
|
Arguments="-d /dev/js0"
|
|
|
|
# -d --device Select the input device to use [/dev/js0]
|
|
# -a --axes Modify the axis map
|
|
# -b --buttons Modify the button map
|
|
# -h --help Show this help information
|
|
|
|
|
|
|
|
[lb216]
|
|
# LB216 driver
|
|
|
|
Arguments="-d /dev/ttyS0 -s 9600"
|
|
|
|
# -d --device Select the output device to use [/dev/lcd]
|
|
# -t --type Select the LCD type (size) [16x2]
|
|
# -b --brightness Set the initial brightness [255]
|
|
# -s --speed Set the communication speed [9600]
|
|
# -r --reboot Reinitialize the LCD's BIOS
|
|
# -h --help Show this help information;
|
|
|
|
|
|
|
|
[mtc_s16209x]
|
|
# MTC-S16209x driver
|
|
|
|
Arguments="-d /dev/ttyS0"
|
|
|
|
# -d --device Select the output device to use [/dev/lcd]
|
|
# -h --help Show this help information;
|
|
|
|
|
|
|
|
[lcdm001]
|
|
# LCDM001 driver
|
|
|
|
Device=/dev/ttyS1
|
|
|
|
# keypad settings
|
|
# Keyname Function
|
|
# Normal context Menu context
|
|
# ------- -------------- ------------
|
|
#
|
|
# PauseKey Pause/Continue Enter/select
|
|
# BackKey Back(Go to previous screen) Up/Left
|
|
# ForwardKey Forward(Go to next screen) Down/Right
|
|
# MainMenuKey Open main menu Exit/Cancel
|
|
|
|
PauseKey=LeftKey
|
|
BackKey=UpKey
|
|
ForwardKey=DownKey
|
|
MainMenuKey=RightKey
|
|
|
|
# You can rearrange the settings here.
|
|
# If your device is broken, have a look at server/drivers/lcdm001.h
|
|
|
|
|
|
|
|
[lcterm]
|
|
# HNE LCTerm driver
|
|
Device=/dev/ttyS1
|
|
size=16x2
|
|
|
|
|
|
|
|
[icp_a106]
|
|
# ICP A106 driver
|
|
Device=/dev/ttyS1
|
|
|
|
|
|
|
|
[lirc]
|
|
# LIRC input driver
|
|
|
|
#lircrc=/etc/lircrc.lcdproc
|
|
# Specify an alternative location of the lircrc file, which is
|
|
# normally ~/.lircrc
|
|
|
|
#prog=lcdd
|
|
# Must be the same as in your lircrc
|
|
|
|
|
|
|
|
[MtxOrb]
|
|
# Matrix Orbital driver
|
|
|
|
# Select the output device to use [/dev/lcd]
|
|
device=/dev/ttyS0
|
|
|
|
# Set the display size [20x4]
|
|
size=20x4
|
|
|
|
# Switch on the backlight? [yes]
|
|
# NOTE: The driver will ignore this if the display
|
|
# is a vfd or vfd as they crash if the backlight
|
|
# is turned off
|
|
enablebacklight=yes
|
|
|
|
# Set the initial contrast [140]
|
|
# NOTE: The driver will ignore this if the display
|
|
# is a vfd or vfd as they don't have this feature
|
|
contrast=800
|
|
|
|
# Set the communication speed [19200]
|
|
speed=19200
|
|
|
|
# Set the display type [lcd]
|
|
# Possible settings: lcd, lkd, vfd, vkd
|
|
type=lkd
|
|
|
|
# The following table translate from MtxOrb Key to Logical Key.
|
|
# See [input] section for an explanation of the key mappings
|
|
# This is a new implementation in 0.5
|
|
LeftKey=A
|
|
RightKey=B
|
|
EnterKey=C
|
|
UpKey=D
|
|
DownKey=E
|
|
EscapeKey=F
|
|
|
|
# You can find out which key of your display sends which
|
|
# character by setting keypad_test_mode to yes and running
|
|
# LCDd. LCDd will output all characters it receives.
|
|
# Afterwards you can modify the settings above and set
|
|
# keypad_set_mode to no again.
|
|
|
|
keypad_test_mode=no
|
|
|
|
|
|
|
|
[sed1330]
|
|
# Seiko Epson 1330 driver
|
|
|
|
Port=0x378
|
|
# Port where the LPT is. Usual values are 0x278, 0x378 and 0x3BC
|
|
|
|
Type=G321D
|
|
#Type=G121C
|
|
#Type=G242C
|
|
# Type of LCD module. G321D is the only one that is tested currently.
|
|
|
|
|
|
|
|
[sed1520]
|
|
# Seiko Epson 1520 driver
|
|
|
|
Arguments="-p 0x278"
|
|
|
|
# -p n --port n Select the output device to use port n
|
|
# -h --help Show this help information
|
|
|
|
|
|
|
|
[stv5730]
|
|
# stv5730 driver
|
|
|
|
Arguments="fill in here"
|
|
|
|
# -p n --port n Select the output device to use port n
|
|
# -h --help Show this help information
|
|
|
|
|
|
|
|
[svgalib]
|
|
# SVGAlib driver
|
|
|
|
# No options.
|
|
# You should of course have your svgalib configured correctly.
|
|
|
|
|
|
|
|
[T6963]
|
|
# Toshiba T6963 driver
|
|
|
|
#Port=0x378
|
|
#Size=20x6
|
|
#ECPlpt=on # use bidirectional mode or not
|
|
|
|
|
|
|
|
[text]
|
|
# Text driver
|
|
|
|
# No options
|
|
|
|
|
|
|
|
[Wirz-sli]
|
|
# Wirz SLI LCD driver
|
|
|
|
Arguments="fill in here"
|
|
|
|
# -d --device Select the output device to use [/dev/lcd]
|
|
# -s --speed Set the communication speed [19200]
|
|
# -h --help Show this help information
|
|
|
|
|
|
|
|
[ms6931]
|
|
# MSI MS-6931 driver for displays in 1HU servers
|
|
Device=/dev/ttyS1
|
|
#Size=16x2
|