This section talks about using LCDproc with graphical LCD displays driven by the EPSON/SMOS SED1330 or SED1335 LCD controllers, which may also be known by their new names: S1D13300 (= SED1330) and S1D13305 (SED1335). The displays are driven in text mode using their built-in character generator. Connections below are for the G242C, G121C and G321D displays. Always consult documentation about the specific display before asuming the connections given here are also correct for your display ! ConnectionType classic ordered by LCD pins pin LPT port ^RESET 1 1 ^STROBE ^RD 2 +5V ^WR 3 16 ^INIT SEL1 4 GND SEL2 5 GND ^CS 6 GND A0 7 17 ^SELECT_IN D0 8 2 D0 D1 9 3 D1 D2 10 4 D2 D3 11 5 D3 D4 12 6 D4 D5 13 7 D5 D6 14 8 D6 D7 15 9 D7 Vdd 16 +5V Vss 17 GND 18..25 GND V0 18 potmeter Vlc 19 -24V Frame 20 GND 10 ^ACK GND 11 BUSY 12 PAPEREND 13 ^SELECT 14 ^LF 15 ^ERROR ]]> ConnectionType classic ordered by LPT port pins pin LPT port ^RESET 1 1 ^STROBE D0 8 2 D0 D1 9 3 D1 D2 10 4 D2 D3 11 5 D3 D4 12 6 D4 D5 13 7 D5 D6 14 8 D6 D7 15 9 D7 10 ^ACK GND 11 BUSY 12 PAPEREND 13 ^SELECT 14 ^LF 15 ^ERROR ^WR 3 16 ^INIT A0 7 17 ^SELECT_IN Vss 17 GND 18..25 GND ^RD 2 +5V SEL1 4 GND SEL2 5 GND ^CS 6 GND Vdd 16 +5V V0 18 potmeter Vlc 19 -24V (not required for G242C) Frame 20 GND ]]> The potmeter should be connected like this on these display modules: The G242C generates -24V internally. It is available on Vlc. To generate -24 from the +5V without an external power source, you can use the following circuit. CellSize= WIDTH x HEIGHT Specify the size of a character in pixels. WIDTH may vary between 6 and 8; legal values for HEIGHT range from 7 to 16. If not given CellSize defaults to 6x10. ConnectionType= classic bitshaker Select the type of the wiring. ConnectionType Wiring classic ^WR = LPT pin 16, A0 = LPT pin 17, ^RESET = LPT pin 1 bitshaker ^WR = LPT pin 1, A0 = LPT pin 14, ^RESET = LPT pin 16 If not given, it defaults to classic. Port= PORT Specify the address of the parallel port the LCD is connected to. Common values for PORT are 0x278, 0x378 and 0x3BC. If not given, it defaults to 0x278. Type= G321D G121C G242C G191D G2446 SP14Q002 Type of LCD module. Besised other things (internal setup) this configuration setting detrmines the size of the display in pixels. Type Size (in pixels) G321D 320 x 200 G121C 128 x 128 G242C 240 x 128 G191D 192 x 192 G2446 240 x 64 SP14Q002 320 x 240 Currently the G321D and SP14Q002 are the only ones that this driver is tested with. Contrary to other drivers the character size of an LCD using the sed1330i driver is not given directly. Instead it is determined by the pixel size of the display, which is derived from the display type setting and the character cell size.