With the chamber open the bed fans only blow room air past the bed. PRINT_WARMUP sets print_fans_off for CHAMBER 30 or less, _PRINT_CLEANUP clears it. Chamber prints, the cooldown and heating the bed outside a print are unchanged. The PID values in PRINT_WARMUP never took effect: the SET_HEATER_TEMPERATURE override in bed_fans.cfg only passes on the target. The bed keeps its config values; the misleading console messages are gone. Tested with rendered macros only, not yet on the printer. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
182 lines
5.7 KiB
INI
182 lines
5.7 KiB
INI
# Bed fans driven by the bed heater (based on Ellis' bed fan macros)
|
|
#
|
|
# During a print without a heated chamber the fans stay off while the bed heats,
|
|
# soaks and prints: with the chamber open they only blow room air past the bed.
|
|
# PRINT_WARMUP sets print_fans_off, _PRINT_CLEANUP clears it. The cooldown after
|
|
# the print and heating the bed outside a print are not affected.
|
|
|
|
############### Config options ##################
|
|
|
|
[gcode_macro _BEDFANVARS]
|
|
variable_threshold: 50 # If bed temp target is above this threshold, fans will be enabled. If temp is set to below this threshold, fans will be disabled.
|
|
variable_fast: 1.0 # Fan speed once bed temp is reached
|
|
variable_slow: 0.5 # Fan speed while bed is heating
|
|
variable_cooldown_temp: 40 # NEW: fans stop below this temp
|
|
variable_print_fans_off: False # set by PRINT_WARMUP for a print without a heated chamber
|
|
gcode:
|
|
|
|
########## Aliases #########
|
|
|
|
[gcode_macro BEDFANSSLOW]
|
|
gcode:
|
|
# Vars
|
|
{% set SLOW = printer["gcode_macro _BEDFANVARS"].slow|float %}
|
|
|
|
SET_FAN_SPEED FAN=BedFans SPEED={SLOW}
|
|
|
|
[gcode_macro BEDFANSFAST]
|
|
gcode:
|
|
# Vars
|
|
{% set FAST = printer["gcode_macro _BEDFANVARS"].fast|float %}
|
|
|
|
SET_FAN_SPEED FAN=BedFans SPEED={FAST}
|
|
|
|
[gcode_macro BEDFANSOFF]
|
|
gcode:
|
|
SET_FAN_SPEED FAN=BedFans SPEED=0
|
|
|
|
############ Command overrides ############
|
|
|
|
# Override, set fan speeds to low and start monitoring loop.
|
|
[gcode_macro SET_HEATER_TEMPERATURE]
|
|
rename_existing: _SET_HEATER_TEMPERATURE
|
|
gcode:
|
|
# Parameters
|
|
{% set HEATER = params.HEATER|default("None") %}
|
|
{% set TARGET = params.TARGET|default(0)|int %}
|
|
# Vars
|
|
{% set THRESHOLD = printer["gcode_macro _BEDFANVARS"].threshold|int %}
|
|
{% set COOLDOWN = printer["gcode_macro _BEDFANVARS"].cooldown_temp|int %}
|
|
{% set FANS_OFF = printer["gcode_macro _BEDFANVARS"].print_fans_off %}
|
|
|
|
{% if HEATER|lower == "extruder" %}
|
|
M104 S{TARGET}
|
|
|
|
# {% elif HEATER|lower == "iHeater_H" %}
|
|
# _SET_HEATER_TEMPERATURE {rawparams}
|
|
|
|
{% elif HEATER|lower == "heater_bed" %}
|
|
M99140 S{TARGET}
|
|
|
|
# Always cancel cooldown loop first (prevents overlap)
|
|
UPDATE_DELAYED_GCODE ID=bedfancooldown DURATION=0
|
|
|
|
# --- NEW LOGIC BLOCK ---
|
|
{% if TARGET == 0 %}
|
|
# Bed turning off → start cooldown behavior
|
|
{% if printer.heater_bed.temperature|int > COOLDOWN %}
|
|
BEDFANSSLOW
|
|
UPDATE_DELAYED_GCODE ID=bedfancooldown DURATION=5
|
|
{% else %}
|
|
BEDFANSOFF
|
|
{% endif %}
|
|
|
|
# Stop normal heating loop if running
|
|
UPDATE_DELAYED_GCODE ID=bedfanloop DURATION=0
|
|
|
|
{% elif TARGET >= THRESHOLD and not FANS_OFF %}
|
|
# Heating above threshold
|
|
BEDFANSSLOW
|
|
UPDATE_DELAYED_GCODE ID=bedfanloop DURATION=1
|
|
|
|
{% else %}
|
|
# Low temp request, or a print without a heated chamber
|
|
BEDFANSOFF
|
|
UPDATE_DELAYED_GCODE ID=bedfanloop DURATION=0
|
|
{% endif %}
|
|
# --- END NEW LOGIC ---
|
|
|
|
{% else %}
|
|
# {action_respond_info("(Bedfans macro)Heater %s not supported (trying classic _SET_HEATER_TEMPERATURE)" % HEATER)}
|
|
_SET_HEATER_TEMPERATURE {rawparams}
|
|
{% endif %}
|
|
|
|
# Override M190 (Wait for Bed Temperature)
|
|
# As a bonus, use TEMPERATURE_WAIT so we don't have to wait for PID to level off.
|
|
[gcode_macro M190]
|
|
rename_existing: M99190
|
|
gcode:
|
|
# Parameters
|
|
{% set S = params.S|int %}
|
|
# Vars
|
|
{% set THRESHOLD = printer["gcode_macro _BEDFANVARS"].threshold|int %}
|
|
{% set FANS_ON = S >= THRESHOLD and not printer["gcode_macro _BEDFANVARS"].print_fans_off %}
|
|
|
|
{% if FANS_ON %}
|
|
BEDFANSSLOW # >= Threshold temp: Low speed fans while heating
|
|
{% else %}
|
|
BEDFANSOFF # < Threshold temp: Turn bed fans off
|
|
{% endif %}
|
|
|
|
M140 {% for p in params
|
|
%}{'%s%s' % (p, params[p])}{%
|
|
endfor %} # Set bed temp
|
|
|
|
{% if S != 0 %}
|
|
TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={S|int} MAXIMUM={S|int + 5} # Wait for bed temp within 5 degrees
|
|
{% endif %}
|
|
|
|
# Post-heating fan speeds
|
|
{% if FANS_ON %}
|
|
BEDFANSFAST # >= Threshold temp: Higher speed fans after heating finished
|
|
{% endif %}
|
|
|
|
# Replace M140 (Set Bed Temperature) to just be an alias of SET_HEATER_TEMPERATURE (which has associated bed fan logic if enabled)
|
|
[gcode_macro M140]
|
|
rename_existing: M99140
|
|
gcode:
|
|
# Parameters
|
|
{% set S = params.S|float %}
|
|
|
|
SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={S}
|
|
|
|
# Replace TURN_OFF_HEATERS
|
|
# [gcode_macro TURN_OFF_HEATERS]
|
|
# rename_existing: _TURN_OFF_HEATERS
|
|
# gcode:
|
|
# BEDFANSOFF
|
|
# _TURN_OFF_HEATERS
|
|
[gcode_macro TURN_OFF_HEATERS]
|
|
rename_existing: _TURN_OFF_HEATERS
|
|
gcode:
|
|
# Vars
|
|
{% set COOLDOWN = printer["gcode_macro _BEDFANVARS"].cooldown_temp|int %}
|
|
|
|
# Only keep fans running if bed is still hot
|
|
{% if printer.heater_bed.temperature|int > COOLDOWN %}
|
|
BEDFANSSLOW
|
|
UPDATE_DELAYED_GCODE ID=bedfancooldown DURATION=5
|
|
{% else %}
|
|
BEDFANSOFF
|
|
{% endif %}
|
|
|
|
_TURN_OFF_HEATERS
|
|
|
|
################ Monitoring loop #####################
|
|
|
|
# Turns bed fans to "fast" speed once target bed temp is reached.
|
|
[delayed_gcode bedfanloop]
|
|
gcode:
|
|
# Vars
|
|
{% set THRESHOLD = printer["gcode_macro _BEDFANVARS"].threshold|int %}
|
|
|
|
{% if printer.heater_bed.target >= THRESHOLD and not printer["gcode_macro _BEDFANVARS"].print_fans_off %} # Continue only if target temp greater than threshold.
|
|
{% if printer.heater_bed.temperature|int >= (printer.heater_bed.target|int - 1) %}
|
|
BEDFANSFAST # If within 1 degree of target temp: Higher speed fans
|
|
{% else %}
|
|
UPDATE_DELAYED_GCODE ID=bedfanloop DURATION=5 # If temp not reached yet: loop again
|
|
{% endif %}
|
|
{% endif %}
|
|
|
|
[delayed_gcode bedfancooldown]
|
|
gcode:
|
|
# Vars
|
|
{% set COOLDOWN = printer["gcode_macro _BEDFANVARS"].cooldown_temp|int %}
|
|
|
|
{% if printer.heater_bed.temperature|int > COOLDOWN %}
|
|
BEDFANSSLOW
|
|
UPDATE_DELAYED_GCODE ID=bedfancooldown DURATION=10
|
|
{% else %}
|
|
BEDFANSOFF
|
|
{% endif %}
|