mangavalkandClaude Opus 5.5
e5be65834e
The motion timeout switched the nozzle LEDs off during prints, motion switched them off when idle or paused, the timeout counted from the first movement, and every _status_* macro stopped the nozzle light. - _LIGHTS sets case light and nozzle LEDs from presence, print state and CASELIGHT MODE=AUTO|ON|OFF; the timeout (60 s) starts at the sensor release - _STATUS STATE=... replaces the _status_* macros; logo effects only cover the logo LEDs and use REPLACE=1 - heater gauge while heating, print progress, paused, error flash from _ERROR, part ready once the bed is cool, dim night mode when idle and nobody near, cleaning during BLOBIFIER_CLEAN - removed unused effects and macros, 12 fps for the toolhead effects Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
269 lines
8.2 KiB
INI
269 lines
8.2 KiB
INI
# Stealthburner LEDs: logo status effects (_STATUS) and the nozzle light
|
|
#
|
|
# Based on the Rainbow Barf logo LED effects by tanaes:
|
|
# https://github.com/tanaes/whopping_Voron_mods/blob/main/LEDs/Rainbow_Barf_Logo_LED/Code/stealthburner_led_effects_barf.cfg
|
|
# which builds on the Voron Stealthburner LED macros. Needs klipper-led_effect.
|
|
#
|
|
# sb_leds 1-8 are the logo, 9-10 the nozzle LEDs. The logo shows the printer
|
|
# status (_STATUS); the nozzle LEDs are white while someone is near the
|
|
# printer (sensors/motion_sensor.cfg). led_effect adds up effects that share
|
|
# an LED, so the logo effects only cover 1-8 and never stop the nozzle light.
|
|
#
|
|
# _STATUS STATE=<state> set and show a status
|
|
# _STATUS show the current status again
|
|
# _STATUS_SHOW STATE=... show a status without storing it (cleaning)
|
|
# _STATUS_FLASH STATE=... show a status for a while (_ERROR: error)
|
|
#
|
|
# States: ready, homing, heating_bed, heating_extruder, calibrating_z,
|
|
# leveling, meshing, cleaning, printing, paused, part_ready, error.
|
|
# ready: rainbow while someone is near, dim (logo and Box Turtle
|
|
# logo) when nobody is near
|
|
# heating_*: the logo fills up with the temperature towards the target
|
|
# printing: the logo fills up with the print progress
|
|
# part_ready: blue while the bed is above part_ready_temp, then green
|
|
|
|
[neopixel sb_leds]
|
|
pin: nhk:PD3
|
|
chain_count: 10
|
|
color_order: GRB, GRB, GRB, GRB, GRB, GRB, GRB, GRB, GRB, GRB
|
|
# Magenta until the first effect starts: shows that the chain and the
|
|
# colour order are right
|
|
initial_RED: 1.0
|
|
initial_GREEN: 0.0
|
|
initial_BLUE: 1.0
|
|
initial_WHITE: 0.0
|
|
|
|
# led_effect sends the whole chain at the rate of the fastest effect running
|
|
# on it, so all sb_leds effects use 12 fps.
|
|
|
|
##################
|
|
## logo effects ##
|
|
##################
|
|
|
|
[led_effect sb_logo_ready]
|
|
autostart: false
|
|
frame_rate: 12
|
|
leds:
|
|
neopixel:sb_leds (2,1,3,4,5,6,7,8)
|
|
layers:
|
|
gradient 0.3 1 add (0.3, 0.0, 0.0),(0.0, 0.3, 0.0),(0.0, 0.0, 0.3)
|
|
|
|
[led_effect sb_logo_night]
|
|
autostart: false
|
|
frame_rate: 12
|
|
leds:
|
|
neopixel:sb_leds (2,1,3,4,5,6,7,8)
|
|
layers:
|
|
static 0 0 top (0.02, 0.02, 0.02)
|
|
|
|
[led_effect bt_logo_night]
|
|
autostart: false
|
|
frame_rate: 10
|
|
leds:
|
|
neopixel:bt_logo
|
|
layers:
|
|
static 0 0 top (0.02, 0.02, 0.02)
|
|
|
|
[led_effect sb_logo_homing]
|
|
autostart: false
|
|
frame_rate: 12
|
|
leds:
|
|
neopixel:sb_leds (2,1,3,4,5,6,7,8)
|
|
layers:
|
|
breathing 3 1 top (0.0, 0.6, 0.2)
|
|
|
|
# heatergauge: the LEDs light up one by one with temperature / target
|
|
[led_effect sb_logo_heating_bed]
|
|
autostart: false
|
|
frame_rate: 12
|
|
heater: heater_bed
|
|
leds:
|
|
neopixel:sb_leds (2,1,3,4,5,6,7,8)
|
|
layers:
|
|
heatergauge -1 0 add (1.0, 0.18, 0.0),(1.0, 0.18, 0.0)
|
|
static 0 0 top (0.08, 0.015, 0.0)
|
|
|
|
[led_effect sb_logo_heating_extruder]
|
|
autostart: false
|
|
frame_rate: 12
|
|
heater: extruder
|
|
leds:
|
|
neopixel:sb_leds (2,1,3,4,5,6,7,8)
|
|
layers:
|
|
heatergauge -1 0 add (1.0, 0.0, 0.0),(1.0, 0.0, 0.0)
|
|
static 0 0 top (0.08, 0.0, 0.0)
|
|
|
|
[led_effect sb_logo_calibrating_z]
|
|
autostart: false
|
|
frame_rate: 12
|
|
leds:
|
|
neopixel:sb_leds (2,1,3,4,5,6,7,8)
|
|
layers:
|
|
breathing 3 1 top (0.0, 0.0, 0.35)
|
|
|
|
[led_effect sb_logo_leveling]
|
|
autostart: false
|
|
frame_rate: 12
|
|
leds:
|
|
neopixel:sb_leds (2,1,3,4,5,6,7,8)
|
|
layers:
|
|
breathing 3 1 top (0.5, 0.1, 0.4)
|
|
|
|
[led_effect sb_logo_meshing]
|
|
autostart: false
|
|
frame_rate: 12
|
|
leds:
|
|
neopixel:sb_leds (2,1,3,4,5,6,7,8)
|
|
layers:
|
|
breathing 3 1 top (0.2, 1.0, 0.0)
|
|
|
|
[led_effect sb_logo_cleaning]
|
|
autostart: false
|
|
frame_rate: 12
|
|
leds:
|
|
neopixel:sb_leds (2,1,3,4,5,6,7,8)
|
|
layers:
|
|
breathing 3 1 top (0.0, 0.02, 0.5)
|
|
|
|
# progress: the LEDs light up one by one with the print progress
|
|
# (display_status: M73 from the slicer, else the file position)
|
|
[led_effect sb_logo_printing]
|
|
autostart: false
|
|
frame_rate: 12
|
|
leds:
|
|
neopixel:sb_leds (2,1,3,4,5,6,7,8)
|
|
layers:
|
|
progress -1 0 add (0.3, 0.3, 0.3),(0.3, 0.3, 0.3)
|
|
static 0 0 top (0.08, 0.02, 0.0)
|
|
|
|
[led_effect sb_logo_paused]
|
|
autostart: false
|
|
frame_rate: 12
|
|
leds:
|
|
neopixel:sb_leds (2,1,3,4,5,6,7,8)
|
|
layers:
|
|
breathing 2 1 top (1.0, 0.35, 0.0)
|
|
|
|
[led_effect sb_logo_cooling]
|
|
autostart: false
|
|
frame_rate: 12
|
|
leds:
|
|
neopixel:sb_leds (2,1,3,4,5,6,7,8)
|
|
layers:
|
|
breathing 3 1 top (0.0, 0.0, 1.0)
|
|
|
|
[led_effect sb_logo_part_ready]
|
|
autostart: false
|
|
frame_rate: 12
|
|
leds:
|
|
neopixel:sb_leds (2,1,3,4,5,6,7,8)
|
|
layers:
|
|
breathing 3 1 top (0.0, 1.0, 0.0)
|
|
|
|
[led_effect sb_logo_error]
|
|
autostart: false
|
|
frame_rate: 12
|
|
leds:
|
|
neopixel:sb_leds (2,1,3,4,5,6,7,8)
|
|
layers:
|
|
blink 1 0.5 top (1.0, 0.0, 0.0)
|
|
|
|
###################
|
|
## nozzle effect ##
|
|
###################
|
|
|
|
# Switched by _LIGHTS (sensors/motion_sensor.cfg)
|
|
[led_effect sb_nozzle_light]
|
|
autostart: false
|
|
frame_rate: 12
|
|
leds:
|
|
neopixel:sb_leds (9,10)
|
|
layers:
|
|
static 0 0 top (1.0, 1.0, 1.0)
|
|
|
|
#####################
|
|
## all led effects ##
|
|
#####################
|
|
|
|
# Klipper shutdown
|
|
[led_effect sb_critical_error]
|
|
leds:
|
|
neopixel:sb_leds
|
|
layers:
|
|
strobe 1 1.5 add (1.0, 1.0, 1.0)
|
|
breathing 2 0 difference (0.95, 0.0, 0.0)
|
|
static 1 0 top (1.0, 0.0, 0.0)
|
|
autostart: false
|
|
frame_rate: 24
|
|
run_on_error: true
|
|
|
|
##############
|
|
# The Macros #
|
|
##############
|
|
|
|
[gcode_macro _STATUS]
|
|
description: Set the logo status (STATE=ready, homing, heating_bed, ...); without STATE show the current one again
|
|
variable_state: 'ready'
|
|
variable_part_ready_temp: 35 # part_ready: blue until the bed is below this (C), then green
|
|
variable_fade_time: 0.5 # s cross-fade between effects (logo and nozzle light)
|
|
gcode:
|
|
{% set new = params.STATE|default(state)|lower %}
|
|
{% if new != state %}
|
|
SET_GCODE_VARIABLE MACRO=_STATUS VARIABLE=state VALUE="'{new}'"
|
|
{% endif %}
|
|
_STATUS_SHOW STATE={new}
|
|
|
|
[gcode_macro _STATUS_SHOW]
|
|
description: Show STATE on the logo without storing it as the current status
|
|
gcode:
|
|
{% set state = params.STATE|lower %}
|
|
{% set cfg = printer['gcode_macro _STATUS'] %}
|
|
{% set near = printer['gcode_macro _LIGHTS'].near if 'gcode_macro _LIGHTS' in printer else True %}
|
|
{% set night = state == 'ready' and not near %}
|
|
{% set cool = printer.heater_bed.temperature < cfg.part_ready_temp %}
|
|
{% if state == 'ready' %}
|
|
{% set effect = 'sb_logo_night' if night else 'sb_logo_ready' %}
|
|
{% elif state == 'part_ready' %}
|
|
{% set effect = 'sb_logo_part_ready' if cool else 'sb_logo_cooling' %}
|
|
{% else %}
|
|
{% set effect = 'sb_logo_' ~ state %}
|
|
{% endif %}
|
|
{% if ('led_effect ' ~ effect) in printer %}
|
|
# REPLACE: stops the other effects on the logo LEDs, not the nozzle light
|
|
SET_LED_EFFECT EFFECT={effect} REPLACE=1 FADETIME={cfg.fade_time}
|
|
SET_LED_EFFECT EFFECT={'bt_logo_night' if night else 'rainbow_turtle'} REPLACE=1 FADETIME={cfg.fade_time}
|
|
{% else %}
|
|
_WARN MSG="_STATUS: unknown state {state}"
|
|
{% endif %}
|
|
{% if state == 'part_ready' and not cool %}
|
|
UPDATE_DELAYED_GCODE ID=_status_part_ready_check DURATION=30
|
|
{% endif %}
|
|
|
|
[delayed_gcode _status_part_ready_check]
|
|
gcode:
|
|
{% if printer['gcode_macro _STATUS'].state == 'part_ready' %}
|
|
_STATUS
|
|
{% endif %}
|
|
|
|
[gcode_macro _STATUS_FLASH]
|
|
description: Show STATE on the logo for DURATION seconds (default 10), then the current status again
|
|
gcode:
|
|
_STATUS_SHOW STATE={params.STATE}
|
|
UPDATE_DELAYED_GCODE ID=_status_flash_end DURATION={params.DURATION|default(10)|float}
|
|
|
|
# After an error that ended the print (print_stats: error) the logo stays red
|
|
# until the next status (next print, CANCEL_PRINT, idle timeout)
|
|
[delayed_gcode _status_flash_end]
|
|
gcode:
|
|
{% set state = printer['gcode_macro _STATUS'].state %}
|
|
{% if printer.print_stats.state == 'error' and state not in ['ready', 'part_ready'] %}
|
|
_STATUS STATE=error
|
|
{% else %}
|
|
_STATUS
|
|
{% endif %}
|
|
|
|
[delayed_gcode _status_startup]
|
|
initial_duration: 1
|
|
gcode:
|
|
_STATUS STATE=ready
|