mangavalkandClaude Opus 5.5
61fa8acb05
- HOME always homes Z with Beacon contact and recalibrates, also when the printer is already homed (home_method_when_homed = proximity used the model of an earlier print without touching the bed). PRINT_START homes Z again after QGL, before the brush takes the nozzle below Z0. - _Z_CHECK: after the soak, compare Klipper's Z with a BEACON_QUERY reading at Z3 over the bed centre and stop the print above 1 mm. Warns and continues when BEACON_QUERY leaves no new printer.beacon.last_sample. - Nozzle guard (extras/bdp_guard.py, print/nozzle_guard.cfg): reads the bd_pressure force over I2C every 20 ms while armed and, in stop mode, shuts Klipper down on a touch. Armed for HOME X/Y, QGL, Z homing, brush, mesh and the Z check; starts in log mode to collect peaks per phase. - Chamber prints: load and purge the first tool before the chamber heats (_LOAD_FOR_CHAMBER replaces _UNLOAD_FOR_CHAMBER). A cut unload leaves a piece of PLA in the extruder that softened in the hot chamber and jammed the ASA load. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
50 lines
1.8 KiB
INI
50 lines
1.8 KiB
INI
#####################################################################
|
|
# klipper-macros: include this one file from printer.cfg, after
|
|
# [include mainsail.cfg] (it needs [pause_resume], [virtual_sdcard] and
|
|
# [respond] from there, and replaces Mainsail's PAUSE/RESUME/CANCEL_PRINT)
|
|
# and after [include AFC/*.cfg] (bd_pa_spoolman.cfg renames AFC's
|
|
# SET_SPOOL_ID, which only works when AFC is loaded first):
|
|
#
|
|
# [include klipper-macros/klipper-macros.cfg]
|
|
#
|
|
# Comment out what you do not use. Every macro is defined in exactly one
|
|
# file: Klipper merges sections with the same name and the last one wins.
|
|
#####################################################################
|
|
|
|
[include save_variables.cfg] # the one [save_variables] for all macros
|
|
[include messages.cfg] # _ERROR, _WARN: errors and warnings also on the display
|
|
|
|
# Blobifier purge bucket (Turtleblobifier for AFC, modified)
|
|
[include blobifier/blobifier.cfg]
|
|
|
|
# Printing
|
|
[include print/pause_resume.cfg]
|
|
[include print/filament.cfg]
|
|
[include print/nozzle_guard.cfg] # bd_pressure nozzle collision guard (needs extras/bdp_guard.py)
|
|
[include print/homing.cfg]
|
|
[include print/idle_timeout.cfg]
|
|
[include print/print_start_end.cfg]
|
|
|
|
# Heating
|
|
[include heating/bed_fans.cfg]
|
|
[include heating/chamber_iheater.cfg]
|
|
[include heating/heat_soak.cfg]
|
|
[include heating/soak_my_bed.cfg]
|
|
[include heating/filament_drying.cfg]
|
|
|
|
# AFC (Box Turtle)
|
|
[include afc/xy_safety_check.cfg]
|
|
[include afc/lane_tools.cfg]
|
|
[include afc/purge_check.cfg]
|
|
[include afc/purge_until_empty.cfg]
|
|
|
|
# Pressure advance per lane/spool (bd_pressure + Spoolman)
|
|
[include pressure_advance/bd_pa_spoolman.cfg]
|
|
|
|
# Spoolman
|
|
[include spoolman/active_spool.cfg]
|
|
|
|
# LEDs and sensors
|
|
[include leds/stealthburner_leds.cfg]
|
|
[include sensors/motion_sensor.cfg]
|