Motion lights outside the G-code queue (extras/motion_lights.py)
The AM312 case light and nozzle LEDs waited for long commands (heat waits, AFC loads, QGL) because [gcode_button] runs through the G-code queue. The new module reads the pin itself, keeps the timeout on a reactor timer and sets the case light with output_pin's send_async_request and the nozzle LEDs directly on the led_effect object. CASELIGHT and _LIGHTS_ON keep working; _STATUS_SHOW reads printer.motion_lights.near. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
55b04a7cef
commit
f25f348d0b
4 files changed
+269
-100
No files matched your search
@@ -48,7 +48,7 @@ everything below, grouped by topic. Comment out what you do not use there.
|
|||||||
| **leds/** | | |
|
| **leds/** | | |
|
||||||
| `stealthburner_leds.cfg` | Stealthburner logo status (`_STATUS STATE=...`: heating and print progress as a filling logo, paused, error flash from `_ERROR`, part ready once the bed is cool, dim when idle and nobody is near) and the nozzle light | `led_effect`, `neopixel:bt_logo` and `rainbow_turtle` from AFC |
|
| `stealthburner_leds.cfg` | Stealthburner logo status (`_STATUS STATE=...`: heating and print progress as a filling logo, paused, error flash from `_ERROR`, part ready once the bed is cool, dim when idle and nobody is near) and the nozzle light | `led_effect`, `neopixel:bt_logo` and `rainbow_turtle` from AFC |
|
||||||
| **sensors/** | | |
|
| **sensors/** | | |
|
||||||
| `motion_sensor.cfg` | PIR motion sensor: case light and nozzle LEDs on while someone is near (timeout from the last motion), `CASELIGHT MODE=AUTO\|ON\|OFF` | sensor on a pin, `[output_pin caselight]`, `leds/stealthburner_leds.cfg` |
|
| `motion_sensor.cfg` | PIR motion sensor: case light and nozzle LEDs on while someone is near (timeout from the last motion), `CASELIGHT MODE=AUTO\|ON\|OFF`; runs outside the G-code queue, so the lights also react during heat waits and AFC loads | `extras/motion_lights.py`, sensor on a pin, `[output_pin caselight]`, `leds/stealthburner_leds.cfg` |
|
||||||
|
|
||||||
### Klipper modules (`extras/`)
|
### Klipper modules (`extras/`)
|
||||||
|
|
||||||
|
|||||||
@@ -0,0 +1,245 @@
|
|||||||
|
# Case light and nozzle LEDs from a PIR motion sensor, outside the G-code
|
||||||
|
# queue.
|
||||||
|
#
|
||||||
|
# [gcode_button] runs its press/release G-code through the G-code queue, so
|
||||||
|
# the lights waited for whatever command was running (M109/M190 heat waits,
|
||||||
|
# heat soak, AFC loads and cuts, QGL, mesh, purge check). This module reads
|
||||||
|
# the sensor pin itself, keeps the timeout on its own reactor timer and sets
|
||||||
|
# the lights directly:
|
||||||
|
# case light - output_pin's send_async_request (the path Klipper's own
|
||||||
|
# SET_PIN TEMPLATE= uses): not tied to the G-code queue or
|
||||||
|
# the move queue
|
||||||
|
# nozzle LEDs - led_effect's set_enabled/set_fade_time, as SET_LED_EFFECT
|
||||||
|
# does; led_effect animates on its own reactor timer
|
||||||
|
# Only the optional status_gcode (logo night mode) goes through the G-code
|
||||||
|
# queue, from a reactor callback, so it can lag without holding up the light.
|
||||||
|
#
|
||||||
|
# The AM312 keeps its output on as long as it sees movement: press = motion,
|
||||||
|
# release = no more motion. The timeout starts at the release.
|
||||||
|
#
|
||||||
|
# someone near: case light near_value, nozzle LEDs on
|
||||||
|
# nobody near, print/pause: case light print_value, nozzle LEDs off
|
||||||
|
# nobody near, idle: case light idle_value, nozzle LEDs off
|
||||||
|
#
|
||||||
|
# Install: link to ~/klipper/klippy/extras/motion_lights.py (install.sh);
|
||||||
|
# needs a Klipper service restart, not just RESTART.
|
||||||
|
#
|
||||||
|
# Config (replaces [gcode_button am312] - one pin cannot be used twice):
|
||||||
|
# [motion_lights]
|
||||||
|
# pin: !PC0
|
||||||
|
# light: caselight # [output_pin caselight]
|
||||||
|
# nozzle_effect: sb_nozzle_light # [led_effect sb_nozzle_light]; optional
|
||||||
|
# timeout: 60 # s without motion before dimming
|
||||||
|
# near_value: 1.0
|
||||||
|
# print_value: 0.1
|
||||||
|
# idle_value: 0.0
|
||||||
|
# on_value: 1.0 # CASELIGHT MODE=ON without VALUE
|
||||||
|
# fade_time: 0.5 # nozzle LED fade (s)
|
||||||
|
# status_gcode: _STATUS # run when 'near' changes; optional
|
||||||
|
# startup_delay: 2 # s after ready: lights on as after motion
|
||||||
|
#
|
||||||
|
# Commands:
|
||||||
|
# CASELIGHT [MODE=AUTO|ON|OFF] [VALUE=0-1] no MODE: report the state
|
||||||
|
# _LIGHTS_ON lights on as if someone walked by (print start/end, resume)
|
||||||
|
# MOTION_LIGHTS_DEBUG [ENABLE=0|1] report every change
|
||||||
|
#
|
||||||
|
# Status (printer.motion_lights): mode, present, near, motion (sensor pin),
|
||||||
|
# value (the case light value last set by this module), timeout, on_value.
|
||||||
|
#
|
||||||
|
# The desired light is applied only when it changes, so a value set with
|
||||||
|
# SET_PIN in Mainsail lasts until the next change (motion, timeout or print
|
||||||
|
# state), as before.
|
||||||
|
|
||||||
|
import logging
|
||||||
|
|
||||||
|
POLL_TIME = 1.0
|
||||||
|
|
||||||
|
|
||||||
|
class MotionLights:
|
||||||
|
def __init__(self, config):
|
||||||
|
self.printer = printer = config.get_printer()
|
||||||
|
self.reactor = printer.get_reactor()
|
||||||
|
self.light_name = config.get('light', 'caselight')
|
||||||
|
self.effect_name = config.get('nozzle_effect', None)
|
||||||
|
self.timeout = config.getfloat('timeout', 60., minval=0.)
|
||||||
|
self.near_value = config.getfloat('near_value', 1., minval=0., maxval=1.)
|
||||||
|
self.print_value = config.getfloat('print_value', 0.1, minval=0.,
|
||||||
|
maxval=1.)
|
||||||
|
self.idle_value = config.getfloat('idle_value', 0., minval=0., maxval=1.)
|
||||||
|
self.on_value = config.getfloat('on_value', 1., minval=0., maxval=1.)
|
||||||
|
self.fade_time = config.getfloat('fade_time', 0.5, minval=0.)
|
||||||
|
self.status_gcode = config.get('status_gcode', None)
|
||||||
|
self.startup_delay = config.getfloat('startup_delay', 2., minval=0.)
|
||||||
|
self.mode = 'auto'
|
||||||
|
self.present = False
|
||||||
|
self.near = False
|
||||||
|
self.motion = False
|
||||||
|
self.off_time = self.reactor.NEVER
|
||||||
|
self.applied = None # (value, lit) last applied
|
||||||
|
self.ready = False
|
||||||
|
self.debug = False
|
||||||
|
self.light = self.effect = self.print_stats = None
|
||||||
|
self.timer = None
|
||||||
|
buttons = printer.load_object(config, 'buttons')
|
||||||
|
buttons.register_debounce_button(config.get('pin'),
|
||||||
|
self._button_callback, config)
|
||||||
|
self.gcode = printer.lookup_object('gcode')
|
||||||
|
self.gcode.register_command('CASELIGHT', self.cmd_CASELIGHT,
|
||||||
|
desc=self.cmd_CASELIGHT_help)
|
||||||
|
self.gcode.register_command('_LIGHTS_ON', self.cmd_LIGHTS_ON,
|
||||||
|
desc=self.cmd_LIGHTS_ON_help)
|
||||||
|
self.gcode.register_command('MOTION_LIGHTS_DEBUG',
|
||||||
|
self.cmd_MOTION_LIGHTS_DEBUG,
|
||||||
|
desc=self.cmd_MOTION_LIGHTS_DEBUG_help)
|
||||||
|
printer.register_event_handler('klippy:connect', self._handle_connect)
|
||||||
|
printer.register_event_handler('klippy:ready', self._handle_ready)
|
||||||
|
|
||||||
|
def _handle_connect(self):
|
||||||
|
# Missing objects are a config error: raising here (connect, not a
|
||||||
|
# runtime callback) stops Klipper with a clear message
|
||||||
|
self.light = self.printer.lookup_object('output_pin ' + self.light_name)
|
||||||
|
if self.effect_name:
|
||||||
|
self.effect = self.printer.lookup_object(
|
||||||
|
'led_effect ' + self.effect_name)
|
||||||
|
self.print_stats = self.printer.lookup_object('print_stats', None)
|
||||||
|
|
||||||
|
def _handle_ready(self):
|
||||||
|
self.timer = self.reactor.register_timer(
|
||||||
|
self._poll, self.reactor.monotonic() + self.startup_delay)
|
||||||
|
|
||||||
|
# Sensor and timeout -------------------------------------------------
|
||||||
|
|
||||||
|
def _button_callback(self, eventtime, state):
|
||||||
|
# Runs in the reactor; must never raise
|
||||||
|
try:
|
||||||
|
self.motion = bool(state)
|
||||||
|
if state:
|
||||||
|
self.present = True
|
||||||
|
self.off_time = self.reactor.NEVER
|
||||||
|
else:
|
||||||
|
self.off_time = self.reactor.monotonic() + self.timeout
|
||||||
|
self._update()
|
||||||
|
except Exception:
|
||||||
|
logging.exception("motion_lights: button callback")
|
||||||
|
|
||||||
|
def _wake(self):
|
||||||
|
self.present = True
|
||||||
|
self.off_time = (self.reactor.NEVER if self.motion
|
||||||
|
else self.reactor.monotonic() + self.timeout)
|
||||||
|
self._update()
|
||||||
|
|
||||||
|
def _poll(self, eventtime):
|
||||||
|
try:
|
||||||
|
if not self.ready:
|
||||||
|
self.ready = True # first run, startup_delay after ready
|
||||||
|
self._wake()
|
||||||
|
if self.present and eventtime >= self.off_time:
|
||||||
|
self.present = False
|
||||||
|
self.off_time = self.reactor.NEVER
|
||||||
|
self._update()
|
||||||
|
except Exception:
|
||||||
|
logging.exception("motion_lights: poll")
|
||||||
|
return eventtime + POLL_TIME
|
||||||
|
|
||||||
|
# Applying -----------------------------------------------------------
|
||||||
|
|
||||||
|
def _busy(self):
|
||||||
|
if self.print_stats is None:
|
||||||
|
return False
|
||||||
|
try:
|
||||||
|
state = self.print_stats.get_status(
|
||||||
|
self.reactor.monotonic())['state']
|
||||||
|
except Exception:
|
||||||
|
return False
|
||||||
|
return state in ('printing', 'paused')
|
||||||
|
|
||||||
|
def _desired(self):
|
||||||
|
if self.mode == 'on':
|
||||||
|
return self.on_value, True
|
||||||
|
if self.mode == 'off':
|
||||||
|
return 0., False
|
||||||
|
if self.present:
|
||||||
|
return self.near_value, True
|
||||||
|
return (self.print_value if self._busy() else self.idle_value), False
|
||||||
|
|
||||||
|
def _update(self):
|
||||||
|
if not self.ready or self.printer.is_shutdown():
|
||||||
|
return
|
||||||
|
value, lit = self._desired()
|
||||||
|
if (value, lit) == self.applied:
|
||||||
|
return
|
||||||
|
self.applied = (value, lit)
|
||||||
|
if self.debug:
|
||||||
|
self._respond("Lights: mode=%s present=%s busy=%s: case light %.2f,"
|
||||||
|
" nozzle %s" % (self.mode, self.present, self._busy(),
|
||||||
|
value, 'on' if lit else 'off'))
|
||||||
|
try:
|
||||||
|
self.light.gcrq.send_async_request(value / self.light.scale)
|
||||||
|
except Exception:
|
||||||
|
logging.exception("motion_lights: setting %s", self.light_name)
|
||||||
|
if self.effect is not None:
|
||||||
|
try:
|
||||||
|
if self.effect.enabled != lit:
|
||||||
|
self.effect.set_fade_time(self.fade_time)
|
||||||
|
self.effect.set_enabled(lit)
|
||||||
|
except Exception:
|
||||||
|
logging.exception("motion_lights: setting %s", self.effect_name)
|
||||||
|
if self.near != lit:
|
||||||
|
self.near = lit
|
||||||
|
if self.status_gcode:
|
||||||
|
self.reactor.register_callback(self._run_status_gcode)
|
||||||
|
|
||||||
|
def _run_status_gcode(self, eventtime):
|
||||||
|
# Waits for the G-code queue in its own reactor greenlet
|
||||||
|
try:
|
||||||
|
self.gcode.run_script(self.status_gcode)
|
||||||
|
except Exception:
|
||||||
|
logging.exception("motion_lights: status_gcode")
|
||||||
|
|
||||||
|
def _respond(self, msg):
|
||||||
|
try:
|
||||||
|
self.gcode.respond_info(msg)
|
||||||
|
except Exception:
|
||||||
|
pass
|
||||||
|
|
||||||
|
# Commands -----------------------------------------------------------
|
||||||
|
|
||||||
|
cmd_CASELIGHT_help = ("Case light and nozzle LEDs: MODE=AUTO (motion"
|
||||||
|
" sensor), ON [VALUE=0-1] or OFF; no MODE: show the"
|
||||||
|
" mode")
|
||||||
|
def cmd_CASELIGHT(self, gcmd):
|
||||||
|
mode = gcmd.get('MODE', '').lower()
|
||||||
|
if not mode:
|
||||||
|
gcmd.respond_info(
|
||||||
|
"Case light: mode %s, %s, value %.2f"
|
||||||
|
% (self.mode, 'someone near' if self.present else 'nobody near',
|
||||||
|
self.light.get_status(None)['value'] * self.light.scale))
|
||||||
|
return
|
||||||
|
if mode not in ('auto', 'on', 'off'):
|
||||||
|
raise gcmd.error("CASELIGHT: MODE must be AUTO, ON or OFF")
|
||||||
|
value = gcmd.get_float('VALUE', None)
|
||||||
|
if value is not None:
|
||||||
|
self.on_value = min(max(value, 0.), 1.)
|
||||||
|
self.mode = mode
|
||||||
|
self.applied = None # apply even if the value is unchanged
|
||||||
|
self._update()
|
||||||
|
|
||||||
|
cmd_LIGHTS_ON_help = "Lights on as if someone walked by"
|
||||||
|
def cmd_LIGHTS_ON(self, gcmd):
|
||||||
|
self._wake()
|
||||||
|
|
||||||
|
cmd_MOTION_LIGHTS_DEBUG_help = "Report every motion light change"
|
||||||
|
def cmd_MOTION_LIGHTS_DEBUG(self, gcmd):
|
||||||
|
self.debug = bool(gcmd.get_int('ENABLE', 1))
|
||||||
|
gcmd.respond_info("motion_lights debug %s"
|
||||||
|
% ('on' if self.debug else 'off'))
|
||||||
|
|
||||||
|
def get_status(self, eventtime):
|
||||||
|
value = self.applied[0] if self.applied else 0.
|
||||||
|
return {'mode': self.mode, 'present': self.present, 'near': self.near,
|
||||||
|
'motion': self.motion, 'value': value,
|
||||||
|
'timeout': self.timeout, 'on_value': self.on_value}
|
||||||
|
|
||||||
|
|
||||||
|
def load_config(config):
|
||||||
|
return MotionLights(config)
|
||||||
@@ -172,7 +172,7 @@ layers:
|
|||||||
## nozzle effect ##
|
## nozzle effect ##
|
||||||
###################
|
###################
|
||||||
|
|
||||||
# Switched by _LIGHTS (sensors/motion_sensor.cfg)
|
# Switched by [motion_lights] (sensors/motion_sensor.cfg, extras/motion_lights.py)
|
||||||
[led_effect sb_nozzle_light]
|
[led_effect sb_nozzle_light]
|
||||||
autostart: false
|
autostart: false
|
||||||
frame_rate: 12
|
frame_rate: 12
|
||||||
@@ -218,7 +218,7 @@ description: Show STATE on the logo without storing it as the current status
|
|||||||
gcode:
|
gcode:
|
||||||
{% set state = params.STATE|lower %}
|
{% set state = params.STATE|lower %}
|
||||||
{% set cfg = printer['gcode_macro _STATUS'] %}
|
{% set cfg = printer['gcode_macro _STATUS'] %}
|
||||||
{% set near = printer['gcode_macro _LIGHTS'].near if 'gcode_macro _LIGHTS' in printer else True %}
|
{% set near = printer.motion_lights.near if 'motion_lights' in printer else True %}
|
||||||
{% set night = state == 'ready' and not near %}
|
{% set night = state == 'ready' and not near %}
|
||||||
{% set cool = printer.heater_bed.temperature < cfg.part_ready_temp %}
|
{% set cool = printer.heater_bed.temperature < cfg.part_ready_temp %}
|
||||||
{% if state == 'ready' %}
|
{% if state == 'ready' %}
|
||||||
|
|||||||
@@ -1,8 +1,12 @@
|
|||||||
# PIR motion sensor (AM312): case light and nozzle LEDs while someone is near
|
# PIR motion sensor (AM312): case light and nozzle LEDs while someone is near
|
||||||
#
|
#
|
||||||
# The AM312 keeps its output on as long as it sees movement: press = motion,
|
# Handled by extras/motion_lights.py, outside the G-code queue: the lights
|
||||||
# release = no more motion. The timeout starts at the release, so the lights
|
# react at once, also during heat waits, AFC loads and other long commands
|
||||||
# stay on while someone works at the printer.
|
# (with [gcode_button] they waited for those to finish).
|
||||||
|
#
|
||||||
|
# The AM312 keeps its output on as long as it sees movement. The timeout
|
||||||
|
# starts when the motion stops, so the lights stay on while someone works at
|
||||||
|
# the printer.
|
||||||
#
|
#
|
||||||
# someone near: case light near_value, nozzle LEDs white
|
# someone near: case light near_value, nozzle LEDs white
|
||||||
# nobody near, print/pause: case light print_value, nozzle LEDs off
|
# nobody near, print/pause: case light print_value, nozzle LEDs off
|
||||||
@@ -10,99 +14,19 @@
|
|||||||
# logo and Box Turtle logo dim (_STATUS ready)
|
# logo and Box Turtle logo dim (_STATUS ready)
|
||||||
#
|
#
|
||||||
# CASELIGHT MODE=ON [VALUE=0.5] | OFF | AUTO overrides the sensor until the
|
# CASELIGHT MODE=ON [VALUE=0.5] | OFF | AUTO overrides the sensor until the
|
||||||
# next Klipper restart. Setting the case light in Mainsail only lasts until
|
# next Klipper restart; CASELIGHT alone shows the state. _LIGHTS_ON turns the
|
||||||
# the next motion.
|
# lights on as if someone walked by (print start and end, resume).
|
||||||
|
# MOTION_LIGHTS_DEBUG ENABLE=1 reports every change in the console. Setting
|
||||||
|
# the case light in Mainsail lasts until the next change.
|
||||||
|
|
||||||
[gcode_button am312]
|
[motion_lights]
|
||||||
pin: !PC0
|
pin: !PC0
|
||||||
press_gcode:
|
light: caselight
|
||||||
_MOTION_START
|
nozzle_effect: sb_nozzle_light
|
||||||
release_gcode:
|
timeout: 60 # s without motion before the lights dim or turn off
|
||||||
_MOTION_END
|
near_value: 1.0 # case light while someone is near
|
||||||
|
print_value: 0.1 # case light while printing or paused, nobody near
|
||||||
[gcode_macro _LIGHTS]
|
idle_value: 0.0 # case light while idle, nobody near
|
||||||
description: Set the case light and nozzle LEDs from motion, print state and CASELIGHT mode
|
on_value: 1.0 # case light for CASELIGHT MODE=ON
|
||||||
variable_timeout: 60 # s without motion before the lights dim or turn off
|
fade_time: 0.5 # nozzle LED fade (s), same as _STATUS fade_time
|
||||||
variable_near_value: 1.0 # case light while someone is near
|
status_gcode: _STATUS # night mode of the logo when nobody is near
|
||||||
variable_print_value: 0.1 # case light while printing or paused, nobody near
|
|
||||||
variable_idle_value: 0.0 # case light while idle, nobody near
|
|
||||||
variable_on_value: 1.0 # case light for CASELIGHT MODE=ON
|
|
||||||
variable_mode: 'auto' # auto (motion sensor), on, off: set by CASELIGHT
|
|
||||||
variable_present: False # someone near: set by the motion sensor
|
|
||||||
variable_near: False # lights on (present or MODE=ON): read by _STATUS
|
|
||||||
variable_debug: False # True: report every change in the console
|
|
||||||
gcode:
|
|
||||||
{% set busy = printer.print_stats.state in ['printing', 'paused'] %}
|
|
||||||
{% if mode == 'on' %}
|
|
||||||
{% set lit = True %}
|
|
||||||
{% set value = on_value %}
|
|
||||||
{% elif mode == 'off' %}
|
|
||||||
{% set lit = False %}
|
|
||||||
{% set value = 0.0 %}
|
|
||||||
{% else %}
|
|
||||||
{% set lit = present %}
|
|
||||||
{% set value = near_value if present else (print_value if busy else idle_value) %}
|
|
||||||
{% endif %}
|
|
||||||
{% if debug %}
|
|
||||||
RESPOND MSG="Lights: mode={mode} present={present} print={printer.print_stats.state}: case light {value}, nozzle {'on' if lit else 'off'}"
|
|
||||||
{% endif %}
|
|
||||||
{% if printer['output_pin caselight'].value != value %}
|
|
||||||
SET_PIN PIN=caselight VALUE={value}
|
|
||||||
{% endif %}
|
|
||||||
{% if printer['led_effect sb_nozzle_light'].enabled != lit %}
|
|
||||||
SET_LED_EFFECT EFFECT=sb_nozzle_light {'' if lit else 'STOP=1'} FADETIME={printer['gcode_macro _STATUS'].fade_time}
|
|
||||||
{% endif %}
|
|
||||||
{% if near != lit %}
|
|
||||||
SET_GCODE_VARIABLE MACRO=_LIGHTS VARIABLE=near VALUE={lit}
|
|
||||||
# Night mode of the logo when idle
|
|
||||||
_STATUS
|
|
||||||
{% endif %}
|
|
||||||
|
|
||||||
[gcode_macro _MOTION_START]
|
|
||||||
description: Motion sensor: someone is near
|
|
||||||
gcode:
|
|
||||||
UPDATE_DELAYED_GCODE ID=_motion_timeout DURATION=0
|
|
||||||
{% if not printer['gcode_macro _LIGHTS'].present %}
|
|
||||||
SET_GCODE_VARIABLE MACRO=_LIGHTS VARIABLE=present VALUE=True
|
|
||||||
_LIGHTS
|
|
||||||
{% endif %}
|
|
||||||
|
|
||||||
[gcode_macro _MOTION_END]
|
|
||||||
description: Motion sensor: no more motion, lights off after the timeout
|
|
||||||
gcode:
|
|
||||||
UPDATE_DELAYED_GCODE ID=_motion_timeout DURATION={printer['gcode_macro _LIGHTS'].timeout}
|
|
||||||
|
|
||||||
[delayed_gcode _motion_timeout]
|
|
||||||
gcode:
|
|
||||||
SET_GCODE_VARIABLE MACRO=_LIGHTS VARIABLE=present VALUE=False
|
|
||||||
_LIGHTS
|
|
||||||
|
|
||||||
[gcode_macro _LIGHTS_ON]
|
|
||||||
description: Lights on as if someone walked by (print start and end, startup)
|
|
||||||
gcode:
|
|
||||||
_MOTION_START
|
|
||||||
{% if printer['gcode_button am312'].state == 'RELEASED' %}
|
|
||||||
_MOTION_END
|
|
||||||
{% endif %}
|
|
||||||
|
|
||||||
[delayed_gcode _lights_startup]
|
|
||||||
initial_duration: 2
|
|
||||||
gcode:
|
|
||||||
_LIGHTS_ON
|
|
||||||
|
|
||||||
[gcode_macro CASELIGHT]
|
|
||||||
description: Case light and nozzle LEDs: MODE=AUTO (motion sensor), ON [VALUE=0-1] or OFF; no MODE: show the mode
|
|
||||||
gcode:
|
|
||||||
{% set l = printer['gcode_macro _LIGHTS'] %}
|
|
||||||
{% set mode = params.MODE|default('')|lower %}
|
|
||||||
{% if mode == '' %}
|
|
||||||
RESPOND MSG="Case light: mode {l.mode}, {'someone near' if l.present else 'nobody near'}, value {printer['output_pin caselight'].value}"
|
|
||||||
{% elif mode not in ['auto', 'on', 'off'] %}
|
|
||||||
_ERROR MSG="CASELIGHT: MODE must be AUTO, ON or OFF"
|
|
||||||
{% else %}
|
|
||||||
{% if 'VALUE' in params %}
|
|
||||||
SET_GCODE_VARIABLE MACRO=_LIGHTS VARIABLE=on_value VALUE={[[params.VALUE|float, 0.0]|max, 1.0]|min}
|
|
||||||
{% endif %}
|
|
||||||
SET_GCODE_VARIABLE MACRO=_LIGHTS VARIABLE=mode VALUE="'{mode}'"
|
|
||||||
_LIGHTS
|
|
||||||
{% endif %}
|
|
||||||
Reference in new issue
Block a user