mangavalk/klipper-macros
1
0 Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity

LEDs: nozzle light follows the motion sensor, new logo status macro

Browse Source 
The motion timeout switched the nozzle LEDs off during prints, motion
switched them off when idle or paused, the timeout counted from the first
movement, and every _status_* macro stopped the nozzle light.

- _LIGHTS sets case light and nozzle LEDs from presence, print state and
  CASELIGHT MODE=AUTO|ON|OFF; the timeout (60 s) starts at the sensor
  release
- _STATUS STATE=... replaces the _status_* macros; logo effects only
  cover the logo LEDs and use REPLACE=1
- heater gauge while heating, print progress, paused, error flash from
  _ERROR, part ready once the bed is cool, dim night mode when idle and
  nobody near, cleaning during BLOBIFIER_CLEAN
- removed unused effects and macros, 12 fps for the toolhead effects

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
mangavalkandClaude Opus 5.5 committed 2026-10-17 19:32:42 +02:00
1 parent fbdb2d5e1d
commit e5be65834e
8 files changed
+286 -291
Download Patch File Download Diff File Expand all files Collapse all files

No files matched your search

README.md
+2 -2
View File
@@ -42,9 +42,9 @@ everything below, grouped by topic. Comment out what you do not use there.
| **spoolman/** | | | | **spoolman/** | | |
| `active_spool.cfg` | `SET_ACTIVE_SPOOL`, `CLEAR_ACTIVE_SPOOL` | Spoolman in Moonraker | | `active_spool.cfg` | `SET_ACTIVE_SPOOL`, `CLEAR_ACTIVE_SPOOL` | Spoolman in Moonraker |
| **leds/** | | | | **leds/** | | |
| `stealthburner_leds.cfg` | Stealthburner LED effects and `_status_*` macros | `led_effect` | | `stealthburner_leds.cfg` | Stealthburner logo status (`_STATUS STATE=...`: heating and print progress as a filling logo, paused, error flash from `_ERROR`, part ready once the bed is cool, dim when idle and nobody is near) and the nozzle light | `led_effect`, `neopixel:bt_logo` and `rainbow_turtle` from AFC |
| **sensors/** | | | | **sensors/** | | |
| `motion_sensor.cfg` | PIR motion sensor switching the case light | sensor on a pin, `[output_pin caselight]` | | `motion_sensor.cfg` | PIR motion sensor: case light and nozzle LEDs on while someone is near (timeout from the last motion), `CASELIGHT MODE=AUTO\|ON\|OFF` | sensor on a pin, `[output_pin caselight]`, `leds/stealthburner_leds.cfg` |
### Klipper modules (`extras/`) ### Klipper modules (`extras/`)
macros/blobifier/blobifier.cfg
+2
View File
@@ -544,6 +544,7 @@ gcode:
{% set pos = printer.gcode_move.gcode_position %} {% set pos = printer.gcode_move.gcode_position %}
SAVE_GCODE_STATE NAME=BLOBIFIER_CLEAN_state SAVE_GCODE_STATE NAME=BLOBIFIER_CLEAN_state
_STATUS_SHOW STATE=cleaning
G90 G90
@@ -576,6 +577,7 @@ gcode:
{% endif %} {% endif %}
RESTORE_GCODE_STATE NAME=BLOBIFIER_CLEAN_state RESTORE_GCODE_STATE NAME=BLOBIFIER_CLEAN_state
_STATUS
macros/leds/stealthburner_leds.cfg
+166 -248
View File
@@ -1,216 +1,191 @@
# Stealthburner LEDs: logo status effects (_STATUS) and the nozzle light
#
# Based on the Rainbow Barf logo LED effects by tanaes:
# https://github.com/tanaes/whopping_Voron_mods/blob/main/LEDs/Rainbow_Barf_Logo_LED/Code/stealthburner_led_effects_barf.cfg # https://github.com/tanaes/whopping_Voron_mods/blob/main/LEDs/Rainbow_Barf_Logo_LED/Code/stealthburner_led_effects_barf.cfg
# Macros for setting the status leds on the Voron StealthBurner toolhead (or for any neopixel-type leds). # which builds on the Voron Stealthburner LED macros. Needs klipper-led_effect.
# #
# You will need to configure a neopixel (or other addressable led, such as dotstar). See # sb_leds 1-8 are the logo, 9-10 the nozzle LEDs. The logo shows the printer
# https://www.klipper3d.org/Config_Reference.html#neopixel for configuration details. # status (_STATUS); the nozzle LEDs are white while someone is near the
# printer (sensors/motion_sensor.cfg). led_effect adds up effects that share
# an LED, so the logo effects only cover 1-8 and never stop the nozzle light.
#####################################
# INSTRUCTIONS #
#####################################
# How to use all this stuff:
# #
# 1. Copy this .cfg file into your Klipper config directory and then add [include stealthburner_leds.cfg] # _STATUS STATE=<state> set and show a status
# to the top of your printer.cfg in order for register the LEDs and macros with Klipper. # _STATUS show the current status again
# 2. Define your LEDs by editing [neopixel sb_leds] below and entering the data pin from your control board # _STATUS_SHOW STATE=... show a status without storing it (cleaning)
# as well as the color order. # _STATUS_FLASH STATE=... show a status for a while (_ERROR: error)
# #
# Note: RGB and RGBW are different and must be defined explicitly. RGB and RGBW are also not able to # States: ready, homing, heating_bed, heating_extruder, calibrating_z,
# be mix-and-matched in the same chain. A separate data line would be needed for proper functioning. # leveling, meshing, cleaning, printing, paused, part_ready, error.
# # ready: rainbow while someone is near, dim (logo and Box Turtle
# RGBW LEDs will have a visible yellow-ish phosphor section to the chip. If your LEDs do not have # logo) when nobody is near
# this yellow portion, you have RGB LEDs. # heating_*: the logo fills up with the temperature towards the target
# # printing: the logo fills up with the print progress
# 3. Save your config and restart Klipper. # part_ready: blue while the bed is above part_ready_temp, then green
#
# Note: We set RED and BLUE to 1.0 to make it easier for users and supporters to detect
# misconfigurations or miswiring. The default color format is for Neopixels with a dedicated
# white LED. On startup, all three SB LEDs should light up.
#
# If you get random colors across your LEDs, change the color_order to GRB and restart. Then
# omit the W for each suggested color_order in the next paragraph.
#
# If you get MAGENTA, your color order is correct. If you get CYAN, you need to use RGBW. If
# you get YELLOW, you need to use BRGW (note that BRG is only supported in the latest Klipper
# version).
#
# 4. Once you have confirmed that the LEDs are set up correctly, you must now decide where you want
# these macros called up...which means adding them to your existing gcode macros. NOTHING will happen
# unless you add the STATUS_????? macros to your existing gcode macros.
#
# Example: add STATUS_LEVELING to the beginning of your QGL gcode macro, and then add STATUS_READY
# to the end of it to set the logo LED and nozzle LEDs back to the `ready` state.
#
# Example: add STATUS_CLEANING to the beginning of your nozzle-cleaning macro, and then STATUS_READY
# to the end of it to return the LEDs back to `ready` state.
#
# 5. Feel free to change colors of each macro, create new ones if you have a need to. The macros provided below
# are just an example of what is possible. If you want to try some more complex animations, you will most
# likely have to use WLED with Moonraker and a small micro-controller (please see the LED thread for help inside
# of the stealthburner_beta channel on Discord).
#
#####################################
# END INSTRUCTRUCTIONS #
#####################################
[neopixel sb_leds] [neopixel sb_leds]
pin: nhk:PD3 pin: nhk:PD3
# The pin connected to the neopixel. This parameter must be provided.
chain_count: 10 chain_count: 10
# The number of Neopixel chips that are "daisy chained" to the color_order: GRB, GRB, GRB, GRB, GRB, GRB, GRB, GRB, GRB, GRB
# provided pin. The default is 1 (which indicates only a single # Magenta until the first effect starts: shows that the chain and the
# Neopixel is connected to the pin). # colour order are right
# color_order: GRB, GRB, GRB, GRB, GRB, GRB, GRB, GRB, GRBW, GRBW
color_order: GRB, GRB, GRB, GRB, GRB, GRB, GRB, GRB, GRB, GRB
# Set the pixel order required by the LED hardware. Options are GRB,
# RGB, GRBW, or RGBW. The default is GRB.
initial_RED: 1.0 initial_RED: 1.0
initial_GREEN: 0.0 initial_GREEN: 0.0
initial_BLUE: 1.0 initial_BLUE: 1.0
initial_WHITE: 0.0 initial_WHITE: 0.0
# Sets the initial LED color of the Neopixel. Each value should be
# between 0.0 and 1.0. The WHITE option is only available on RGBW
# LEDs. The default for each color is 0.#
# led_effect sends the whole chain at the rate of the fastest effect running
########################## # on it, so all sb_leds effects use 12 fps.
# LED Effects Animations #
##########################
################## ##################
## logo effects ## ## logo effects ##
################## ##################
[led_effect sb_logo_busy] [led_effect sb_logo_ready]
autostart: false autostart: false
frame_rate: 24 frame_rate: 12
leds: leds:
neopixel:sb_leds (2,1,3,4,5,6,7,8) neopixel:sb_leds (2,1,3,4,5,6,7,8)
layers: layers:
breathing 3 1 top (1,0,0) gradient 0.3 1 add (0.3, 0.0, 0.0),(0.0, 0.3, 0.0),(0.0, 0.0, 0.3)
[led_effect sb_logo_cleaning] [led_effect sb_logo_night]
autostart: false autostart: false
frame_rate: 24 frame_rate: 12
leds: leds:
neopixel:sb_leds (2,1,3,4,5,6,7,8) neopixel:sb_leds (2,1,3,4,5,6,7,8)
layers: layers:
breathing 3 1 top (0.0, 0.02, 0.5) static 0 0 top (0.02, 0.02, 0.02)
[led_effect sb_logo_calibrating_z] [led_effect bt_logo_night]
autostart: false autostart: false
frame_rate: 24 frame_rate: 10
leds: leds:
neopixel:sb_leds (2,1,3,4,5,6,7,8) neopixel:bt_logo
layers: layers:
breathing 3 1 top (0.0, 0.0, 0.35) static 0 0 top (0.02, 0.02, 0.02)
[led_effect sb_logo_heating]
leds:
neopixel:sb_leds (2,3,7,8,6,1)
autostart: false
frame_rate: 24
layers:
comet 0.3 0 add (1, 0.18, 0)
[led_effect sb_logo_cooling]
leds:
neopixel:sb_leds (2,3,7,8,6,1)
autostart: false
frame_rate: 24
layers:
comet 0.3 0 add (0, 0, 1)
[led_effect sb_logo_homing] [led_effect sb_logo_homing]
autostart: false autostart: false
frame_rate: 24 frame_rate: 12
leds: leds:
neopixel:sb_leds (2,1,3,4,5,6,7,8) neopixel:sb_leds (2,1,3,4,5,6,7,8)
layers: layers:
breathing 3 1 top (0.0, 0.6, 0.2) breathing 3 1 top (0.0, 0.6, 0.2)
# heatergauge: the LEDs light up one by one with temperature / target
[led_effect sb_logo_heating_bed]
autostart: false
frame_rate: 12
heater: heater_bed
leds:
neopixel:sb_leds (2,1,3,4,5,6,7,8)
layers:
heatergauge -1 0 add (1.0, 0.18, 0.0),(1.0, 0.18, 0.0)
static 0 0 top (0.08, 0.015, 0.0)
[led_effect sb_logo_heating_extruder]
autostart: false
frame_rate: 12
heater: extruder
leds:
neopixel:sb_leds (2,1,3,4,5,6,7,8)
layers:
heatergauge -1 0 add (1.0, 0.0, 0.0),(1.0, 0.0, 0.0)
static 0 0 top (0.08, 0.0, 0.0)
[led_effect sb_logo_calibrating_z]
autostart: false
frame_rate: 12
leds:
neopixel:sb_leds (2,1,3,4,5,6,7,8)
layers:
breathing 3 1 top (0.0, 0.0, 0.35)
[led_effect sb_logo_leveling] [led_effect sb_logo_leveling]
autostart: false autostart: false
frame_rate: 24 frame_rate: 12
leds: leds:
neopixel:sb_leds (2,1,3,4,5,6,7,8) neopixel:sb_leds (2,1,3,4,5,6,7,8)
layers: layers:
breathing 3 1 top (0.5, 0.1, 0.4) breathing 3 1 top (0.5, 0.1, 0.4)
[led_effect sb_logo_meshing] [led_effect sb_logo_meshing]
autostart: false autostart: false
frame_rate: 24 frame_rate: 12
leds: leds:
neopixel:sb_leds (2,1,3,4,5,6,7,8) neopixel:sb_leds (2,1,3,4,5,6,7,8)
layers: layers:
breathing 3 1 top (0.2, 1.0, 0.0) breathing 3 1 top (0.2, 1.0, 0.0)
[led_effect sb_logo_cleaning]
autostart: false
frame_rate: 12
leds:
neopixel:sb_leds (2,1,3,4,5,6,7,8)
layers:
breathing 3 1 top (0.0, 0.02, 0.5)
# progress: the LEDs light up one by one with the print progress
# (display_status: M73 from the slicer, else the file position)
[led_effect sb_logo_printing] [led_effect sb_logo_printing]
autostart: false autostart: false
frame_rate: 24 frame_rate: 12
leds: leds:
neopixel:sb_leds (2,1,3,4,5,6,7,8) neopixel:sb_leds (2,1,3,4,5,6,7,8)
layers: layers:
gradient 0.3 1 add (0.3, 0.0, 0.0),(0.3, 0.3, 0.0),(0.3, 0.1, 0.0) progress -1 0 add (0.3, 0.3, 0.3),(0.3, 0.3, 0.3)
static 0 0 top (0.08, 0.02, 0.0)
[led_effect sb_logo_standby] [led_effect sb_logo_paused]
autostart: false autostart: false
frame_rate: 24 frame_rate: 12
leds: leds:
neopixel:sb_leds (2,1,3,4,5,6,7,8) neopixel:sb_leds (2,1,3,4,5,6,7,8)
layers: layers:
breathing 3 1 top (0.01, 0.01, 0.01) breathing 2 1 top (1.0, 0.35, 0.0)
[led_effect sb_logo_cooling]
autostart: false
frame_rate: 12
leds:
neopixel:sb_leds (2,1,3,4,5,6,7,8)
layers:
breathing 3 1 top (0.0, 0.0, 1.0)
[led_effect sb_logo_part_ready] [led_effect sb_logo_part_ready]
autostart: false autostart: false
frame_rate: 24 frame_rate: 12
leds: leds:
neopixel:sb_leds (2,1,3,4,5,6,7,8) neopixel:sb_leds (2,1,3,4,5,6,7,8)
layers: layers:
breathing 3 1 top (0.0, 1.0, 0.0) breathing 3 1 top (0.0, 1.0, 0.0)
#################### [led_effect sb_logo_error]
## nozzle effects ##
####################
[led_effect sb_nozzle_heating]
autostart: false autostart: false
frame_rate: 24 frame_rate: 12
leds:
neopixel:sb_leds (2,1,3,4,5,6,7,8)
layers:
blink 1 0.5 top (1.0, 0.0, 0.0)
###################
## nozzle effect ##
###################
# Switched by _LIGHTS (sensors/motion_sensor.cfg)
[led_effect sb_nozzle_light]
autostart: false
frame_rate: 12
leds: leds:
neopixel:sb_leds (9,10) neopixel:sb_leds (9,10)
layers: layers:
breathing 3 1 top (1.0, 0.18, 0.0, 0.0) static 0 0 top (1.0, 1.0, 1.0)
[led_effect sb_nozzle_cooling]
autostart: false
frame_rate: 24
leds:
neopixel:sb_leds (9,10)
layers:
breathing 3 1 top (0.0, 0.0, 1.0, 0.1)
[led_effect sb_nozzle_standby]
autostart: false
frame_rate: 24
leds:
neopixel:sb_leds (9,10)
layers:
breathing 3 1 top (0.6, 0.0, 0.0, 0.0)
[led_effect sb_nozzle_part_ready]
autostart: false
frame_rate: 24
leds:
neopixel:sb_leds (9,10)
layers:
breathing 3 1 top (0.6, 1.0, 0.0, 0.1)
##################### #####################
## all led effects ## ## all led effects ##
##################### #####################
# Klipper shutdown
[led_effect sb_critical_error] [led_effect sb_critical_error]
leds: leds:
neopixel:sb_leds neopixel:sb_leds
@@ -222,129 +197,72 @@ autostart: false
frame_rate: 24 frame_rate: 24
run_on_error: true run_on_error: true
[led_effect rainbow]
leds:
neopixel:sb_leds
autostart: true
frame_rate: 24
layers:
gradient 0.3 1 add (0.3, 0.0, 0.0),(0.0, 0.3, 0.0),(0.0, 0.0, 0.3)
#######################
# LED Effects Statics #
#######################
[led_effect set_nozzle_leds]
leds:
neopixel:sb_leds (9,10)
#neopixel:caselight
autostart: false
frame_rate: 24
layers:
# static 0 0 top (0.0, 0.0, 0.0, 1.0)
static 0 0 top (1.0, 1.0, 1.0, 1.0)
[led_effect set_logo_leds]
leds:
neopixel:sb_leds (2,1,3,4,5,6,7,8)
#neopixel:caselight
autostart: false
frame_rate: 24
layers:
static 0 0 top (1.0, 1.0, 1.0)
############## ##############
# The Macros # # The Macros #
############## ##############
[gcode_macro _set_logo_leds_off] [gcode_macro _STATUS]
description: Set the logo status (STATE=ready, homing, heating_bed, ...); without STATE show the current one again
variable_state: 'ready'
variable_part_ready_temp: 35 # part_ready: blue until the bed is below this (C), then green
variable_fade_time: 0.5 # s cross-fade between effects (logo and nozzle light)
gcode: gcode:
SET_LED_EFFECT EFFECT=set_logo_leds STOP=1 {% set new = params.STATE|default(state)|lower %}
{% if new != state %}
SET_GCODE_VARIABLE MACRO=_STATUS VARIABLE=state VALUE="'{new}'"
{% endif %}
_STATUS_SHOW STATE={new}
[gcode_macro _set_logo_leds_on] [gcode_macro _STATUS_SHOW]
description: Show STATE on the logo without storing it as the current status
gcode: gcode:
SET_LED_EFFECT EFFECT=set_logo_leds {% set state = params.STATE|lower %}
{% set cfg = printer['gcode_macro _STATUS'] %}
{% set near = printer['gcode_macro _LIGHTS'].near if 'gcode_macro _LIGHTS' in printer else True %}
{% set night = state == 'ready' and not near %}
{% set cool = printer.heater_bed.temperature < cfg.part_ready_temp %}
{% if state == 'ready' %}
{% set effect = 'sb_logo_night' if night else 'sb_logo_ready' %}
{% elif state == 'part_ready' %}
{% set effect = 'sb_logo_part_ready' if cool else 'sb_logo_cooling' %}
{% else %}
{% set effect = 'sb_logo_' ~ state %}
{% endif %}
{% if ('led_effect ' ~ effect) in printer %}
# REPLACE: stops the other effects on the logo LEDs, not the nozzle light
SET_LED_EFFECT EFFECT={effect} REPLACE=1 FADETIME={cfg.fade_time}
SET_LED_EFFECT EFFECT={'bt_logo_night' if night else 'rainbow_turtle'} REPLACE=1 FADETIME={cfg.fade_time}
{% else %}
_WARN MSG="_STATUS: unknown state {state}"
{% endif %}
{% if state == 'part_ready' and not cool %}
UPDATE_DELAYED_GCODE ID=_status_part_ready_check DURATION=30
{% endif %}
[gcode_macro _set_nozzle_leds_on] [delayed_gcode _status_part_ready_check]
gcode: gcode:
SET_LED_EFFECT EFFECT=set_nozzle_leds {% if printer['gcode_macro _STATUS'].state == 'part_ready' %}
_STATUS
{% endif %}
[gcode_macro _set_nozzle_leds_off] [gcode_macro _STATUS_FLASH]
description: Show STATE on the logo for DURATION seconds (default 10), then the current status again
gcode: gcode:
SET_LED_EFFECT EFFECT=set_nozzle_leds STOP=1 _STATUS_SHOW STATE={params.STATE}
UPDATE_DELAYED_GCODE ID=_status_flash_end DURATION={params.DURATION|default(10)|float}
# The _status_* macros only stop the toolhead effects (neopixel:sb_leds), so # After an error that ended the print (print_stats: error) the logo stays red
# the Box Turtle logo (rainbow_turtle on neopixel:bt_logo) keeps running during # until the next status (next print, CANCEL_PRINT, idle timeout)
# prints. _status_off still stops everything; _status_ready starts the logo again. [delayed_gcode _status_flash_end]
[gcode_macro _status_off]
gcode: gcode:
STOP_LED_EFFECTS {% set state = printer['gcode_macro _STATUS'].state %}
{% if printer.print_stats.state == 'error' and state not in ['ready', 'part_ready'] %}
_STATUS STATE=error
{% else %}
_STATUS
{% endif %}
[gcode_macro _status_ready] [delayed_gcode _status_startup]
initial_duration: 1
gcode: gcode:
STOP_LED_EFFECTS LEDS="neopixel:sb_leds" _STATUS STATE=ready
SET_LED_EFFECT EFFECT=rainbow
SET_LED_EFFECT EFFECT=rainbow_turtle
[gcode_macro _status_part_ready]
gcode:
STOP_LED_EFFECTS LEDS="neopixel:sb_leds"
SET_LED_EFFECT EFFECT=sb_nozzle_part_ready
SET_LED_EFFECT EFFECT=sb_logo_part_ready
[gcode_macro _status_busy]
gcode:
STOP_LED_EFFECTS LEDS="neopixel:sb_leds"
SET_LED_EFFECT EFFECT=sb_logo_busy
_set_nozzle_leds_on
[gcode_macro _status_heating]
gcode:
STOP_LED_EFFECTS LEDS="neopixel:sb_leds"
SET_LED_EFFECT EFFECT=sb_logo_heating
SET_LED_EFFECT EFFECT=sb_nozzle_heating
[gcode_macro _status_cooling]
gcode:
STOP_LED_EFFECTS LEDS="neopixel:sb_leds"
SET_LED_EFFECT EFFECT=sb_logo_cooling
SET_LED_EFFECT EFFECT=sb_nozzle_cooling
[gcode_macro _status_leveling]
gcode:
STOP_LED_EFFECTS LEDS="neopixel:sb_leds"
SET_LED_EFFECT EFFECT=sb_logo_leveling
_set_nozzle_leds_on
[gcode_macro _status_homing]
gcode:
STOP_LED_EFFECTS LEDS="neopixel:sb_leds"
SET_LED_EFFECT EFFECT=sb_logo_homing
_set_nozzle_leds_on
[gcode_macro _status_cleaning]
gcode:
STOP_LED_EFFECTS LEDS="neopixel:sb_leds"
SET_LED_EFFECT EFFECT=sb_logo_cleaning
_set_nozzle_leds_on
[gcode_macro _status_meshing]
gcode:
STOP_LED_EFFECTS LEDS="neopixel:sb_leds"
SET_LED_EFFECT EFFECT=sb_logo_meshing
_set_nozzle_leds_on
[gcode_macro _status_calibrating_z]
gcode:
STOP_LED_EFFECTS LEDS="neopixel:sb_leds"
SET_LED_EFFECT EFFECT=sb_logo_calibrating_z
_set_nozzle_leds_on
[gcode_macro _status_printing]
gcode:
STOP_LED_EFFECTS LEDS="neopixel:sb_leds"
SET_LED_EFFECT EFFECT=sb_logo_printing
_set_nozzle_leds_on
macros/messages.cfg
+3
View File
@@ -18,6 +18,9 @@
description: Show DISPLAY (default MSG) on the display, then raise MSG as an error (aborts the calling macros) description: Show DISPLAY (default MSG) on the display, then raise MSG as an error (aborts the calling macros)
gcode: gcode:
M117 {params.DISPLAY|default(params.MSG)} M117 {params.DISPLAY|default(params.MSG)}
{% if 'gcode_macro _STATUS_FLASH' in printer %}
_STATUS_FLASH STATE=error
{% endif %}
_RAISE_ERROR MSG="{params.MSG}" _RAISE_ERROR MSG="{params.MSG}"
[gcode_macro _RAISE_ERROR] [gcode_macro _RAISE_ERROR]
macros/print/idle_timeout.cfg
+1 -1
View File
@@ -16,7 +16,7 @@ gcode:
{% if printer.pause_resume.is_paused|lower == 'false' and park|lower == 'true'%} {% if printer.pause_resume.is_paused|lower == 'false' and park|lower == 'true'%}
_TOOLHEAD_PARK_PAUSE_CANCEL _TOOLHEAD_PARK_PAUSE_CANCEL
{% endif %} {% endif %}
_status_ready _STATUS STATE=ready
# A list of G-Code commands to execute on an idle timeout. See # A list of G-Code commands to execute on an idle timeout. See
# docs/Command_Templates.md for G-Code format. The default is to run # docs/Command_Templates.md for G-Code format. The default is to run
# "TURN_OFF_HEATERS" and "M84". # "TURN_OFF_HEATERS" and "M84".
macros/print/pause_resume.cfg
+4 -2
View File
@@ -41,6 +41,7 @@ gcode:
PAUSE_BASE PAUSE_BASE
_TOOLHEAD_PARK_PAUSE_CANCEL _TOOLHEAD_PARK_PAUSE_CANCEL
SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=parked VALUE=True SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=parked VALUE=True
_STATUS STATE=paused
# Set fan to S28 (28/255 ≈ 0.1098) # Set fan to S28 (28/255 ≈ 0.1098)
M106 S28 M106 S28
{% else %} {% else %}
@@ -96,7 +97,7 @@ gcode:
{% endif %} {% endif %}
RESUME_BASE {get_params} RESUME_BASE {get_params}
_status_printing _STATUS STATE=printing
# Raising an error (_ERROR, also shown on the display) aborts the whole # Raising an error (_ERROR, also shown on the display) aborts the whole
# RESUME like a failed purge check: the printer stays paused and the next # RESUME like a failed purge check: the printer stays paused and the next
@@ -203,7 +204,8 @@ gcode:
SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=parked VALUE=False SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=parked VALUE=False
# Clear a pause reason from the display # Clear a pause reason from the display
M117 M117
_status_ready _STATUS STATE=ready
_LIGHTS_ON
[gcode_macro M600] [gcode_macro M600]
# #
macros/print/print_start_end.cfg
+16 -12
View File
@@ -29,7 +29,7 @@ gcode:
# Clear what an earlier print or error left on the display # Clear what an earlier print or error left on the display
M117 M117
_motion_detected _LIGHTS_ON
#SET_PIN PIN=caselight VALUE=1.00 #SET_PIN PIN=caselight VALUE=1.00
UPDATE_DELAYED_GCODE ID=_delayed_motors_off DURATION=0 UPDATE_DELAYED_GCODE ID=_delayed_motors_off DURATION=0
@@ -48,7 +48,7 @@ gcode:
M109 S150 ; wait until nozzle reaches 150 ; wait until nozzle reaches 0 M109 S150 ; wait until nozzle reaches 150 ; wait until nozzle reaches 0
{% endif %} {% endif %}
_status_homing _STATUS STATE=homing
RESPOND MSG="homing" RESPOND MSG="homing"
HOME HOME
RESPOND MSG="homing finished" RESPOND MSG="homing finished"
@@ -63,7 +63,7 @@ gcode:
{% endif %} {% endif %}
G1 X175 Y175 Z2 F1200 G1 X175 Y175 Z2 F1200
_status_heating _STATUS STATE=heating_bed
RESPOND MSG="heating" RESPOND MSG="heating"
{% if target_bed > 0 %} {% if target_bed > 0 %}
M140 S{target_bed} ; start bed heater M140 S{target_bed} ; start bed heater
@@ -72,11 +72,14 @@ gcode:
M190 S{target_bed} ; wait on bed temperature M190 S{target_bed} ; wait on bed temperature
{% endif %} {% endif %}
_STATUS STATE=homing
HOME HOME
_STATUS STATE=leveling
QUAD_GANTRY_LEVEL QUAD_GANTRY_LEVEL
BLOBIFIER_CLEAN ; call another macro to wipe nozzle if available BLOBIFIER_CLEAN ; call another macro to wipe nozzle if available
G1 X175 Y175 Z5 F1200 G1 X175 Y175 Z5 F1200
_STATUS STATE=heating_extruder
_HEAT_FOR_LOADED_LANE TOOL={initial_tool} ; unload needs the loaded filament's temperature _HEAT_FOR_LOADED_LANE TOOL={initial_tool} ; unload needs the loaded filament's temperature
T{initial_tool} #PURGE_LENGTH=100 #Load Initial Tool T{initial_tool} #PURGE_LENGTH=100 #Load Initial Tool
M104 S{target_extruder} ; set extruder to print temp M104 S{target_extruder} ; set extruder to print temp
@@ -89,6 +92,7 @@ gcode:
BLOBIFIER_CLEAN ; call another macro to wipe nozzle if available BLOBIFIER_CLEAN ; call another macro to wipe nozzle if available
G1 X175 Y175 Z5 F1200 G1 X175 Y175 Z5 F1200
_STATUS STATE=heating_bed
{% if target_chamber > 30 %} {% if target_chamber > 30 %}
RESPOND MSG="waiting for chamber temperature" RESPOND MSG="waiting for chamber temperature"
M141 S{target_chamber} M141 S{target_chamber}
@@ -133,7 +137,7 @@ gcode:
gcode: gcode:
RESPOND MSG="print start macro continued" RESPOND MSG="print start macro continued"
_motion_detected _LIGHTS_ON
{% set target_extruder = params.EXTRUDER|int %} {% set target_extruder = params.EXTRUDER|int %}
@@ -145,14 +149,14 @@ gcode:
HOME HOME
BLOBIFIER_CLEAN ; call another macro to wipe nozzle if available BLOBIFIER_CLEAN ; call another macro to wipe nozzle if available
_status_calibrating_z _STATUS STATE=calibrating_z
G28 Z METHOD=CONTACT CALIBRATE=1 ; calibrate z offset and beacon model hot G28 Z METHOD=CONTACT CALIBRATE=1 ; calibrate z offset and beacon model hot
_status_leveling _STATUS STATE=leveling
RESPOND MSG="quad ganrty level" RESPOND MSG="quad ganrty level"
QUAD_GANTRY_LEVEL QUAD_GANTRY_LEVEL
_status_meshing _STATUS STATE=meshing
RESPOND MSG="meshing" RESPOND MSG="meshing"
BED_MESH_CALIBRATE RUNS=2 ; bed mesh in scan mode BED_MESH_CALIBRATE RUNS=2 ; bed mesh in scan mode
@@ -161,10 +165,10 @@ gcode:
M104 S150 ; set nozzle temp to 150 M104 S150 ; set nozzle temp to 150
M109 S150 ; wait until nozzle reaches 150 ; wait until nozzle reaches 0 M109 S150 ; wait until nozzle reaches 150 ; wait until nozzle reaches 0
_status_calibrating_z _STATUS STATE=calibrating_z
G28 Z METHOD=CONTACT CALIBRATE=1 ; calibrate z offset and beacon model hot G28 Z METHOD=CONTACT CALIBRATE=1 ; calibrate z offset and beacon model hot
_status_heating _STATUS STATE=heating_extruder
M104 S{target_extruder} ; set extruder to print temp M104 S{target_extruder} ; set extruder to print temp
M109 S{target_extruder} ; wait for extruder temp M109 S{target_extruder} ; wait for extruder temp
BLOBIFIER_PARK ; over the bucket, then undo the retracts BLOBIFIER_PARK ; over the bucket, then undo the retracts
@@ -209,7 +213,7 @@ gcode:
# per-reading width compensation made the flow jump between 77 and 119%. # per-reading width compensation made the flow jump between 77 and 119%.
# To use it again: SET_BDWIDTH NAME=fila_width_0 COMMAND=ENABLE_WIDTH # To use it again: SET_BDWIDTH NAME=fila_width_0 COMMAND=ENABLE_WIDTH
_status_printing _STATUS STATE=printing
[gcode_macro PRINT_END] [gcode_macro PRINT_END]
@@ -223,7 +227,7 @@ gcode:
SAVE_GCODE_STATE NAME=STATE_PRINT_END SAVE_GCODE_STATE NAME=STATE_PRINT_END
_motion_detected _LIGHTS_ON
M400 ; wait for buffer to clear M400 ; wait for buffer to clear
G92 E0 ; zero the extruder G92 E0 ; zero the extruder
@@ -238,7 +242,7 @@ gcode:
M107 ; turn off fan M107 ; turn off fan
#SET_PIN PIN=caselight VALUE=0.03 #SET_PIN PIN=caselight VALUE=0.03
_status_part_ready _STATUS STATE=part_ready
UPDATE_DELAYED_GCODE ID=_delayed_motors_off DURATION=3600 UPDATE_DELAYED_GCODE ID=_delayed_motors_off DURATION=3600
macros/sensors/motion_sensor.cfg
+92 -26
View File
@@ -1,42 +1,108 @@
# PIR motion sensor: case light on when someone is near the printer # PIR motion sensor (AM312): case light and nozzle LEDs while someone is near
#
# The AM312 keeps its output on as long as it sees movement: press = motion,
# release = no more motion. The timeout starts at the release, so the lights
# stay on while someone works at the printer.
#
# someone near: case light near_value, nozzle LEDs white
# nobody near, print/pause: case light print_value, nozzle LEDs off
# nobody near, idle: case light idle_value, nozzle LEDs off,
# logo and Box Turtle logo dim (_STATUS ready)
#
# CASELIGHT MODE=ON [VALUE=0.5] | OFF | AUTO overrides the sensor until the
# next Klipper restart. Setting the case light in Mainsail only lasts until
# the next motion.
[gcode_button am312] [gcode_button am312]
pin: !PC0 pin: !PC0
press_gcode: press_gcode:
_motion_detected _MOTION_START
release_gcode:
[gcode_macro _motion_detected] _MOTION_END
description: Motion sensor triggered
[gcode_macro _LIGHTS]
description: Set the case light and nozzle LEDs from motion, print state and CASELIGHT mode
variable_timeout: 60 # s without motion before the lights dim or turn off
variable_near_value: 1.0 # case light while someone is near
variable_print_value: 0.1 # case light while printing or paused, nobody near
variable_idle_value: 0.0 # case light while idle, nobody near
variable_on_value: 1.0 # case light for CASELIGHT MODE=ON
variable_mode: 'auto' # auto (motion sensor), on, off: set by CASELIGHT
variable_present: False # someone near: set by the motion sensor
variable_near: False # lights on (present or MODE=ON): read by _STATUS
variable_debug: False # True: report every change in the console
gcode: gcode:
{% set printing = printer.print_stats.state == "printing" %} {% set busy = printer.print_stats.state in ['printing', 'paused'] %}
{% if mode == 'on' %}
# RESPOND MSG="AM312: Motion detected" {% set lit = True %}
{% set value = on_value %}
{% if printing %} {% elif mode == 'off' %}
# RESPOND MSG="AM312: Printer is printing -> light ON (100%)" {% set lit = False %}
SET_PIN PIN=caselight VALUE=1.0 {% set value = 0.0 %}
_set_nozzle_leds_on
{% else %} {% else %}
# RESPOND MSG="AM312: Printer idle -> light ON (10%)" {% set lit = present %}
SET_PIN PIN=caselight VALUE=0.1 {% set value = near_value if present else (print_value if busy else idle_value) %}
_set_nozzle_leds_off {% endif %}
{% if debug %}
RESPOND MSG="Lights: mode={mode} present={present} print={printer.print_stats.state}: case light {value}, nozzle {'on' if lit else 'off'}"
{% endif %}
{% if printer['output_pin caselight'].value != value %}
SET_PIN PIN=caselight VALUE={value}
{% endif %}
{% if printer['led_effect sb_nozzle_light'].enabled != lit %}
SET_LED_EFFECT EFFECT=sb_nozzle_light {'' if lit else 'STOP=1'} FADETIME={printer['gcode_macro _STATUS'].fade_time}
{% endif %}
{% if near != lit %}
SET_GCODE_VARIABLE MACRO=_LIGHTS VARIABLE=near VALUE={lit}
# Night mode of the logo when idle
_STATUS
{% endif %} {% endif %}
# RESPOND MSG="AM312: Resetting timeout to 30 seconds" [gcode_macro _MOTION_START]
UPDATE_DELAYED_GCODE ID=_motion_timeout DURATION=30 description: Motion sensor: someone is near
gcode:
UPDATE_DELAYED_GCODE ID=_motion_timeout DURATION=0
{% if not printer['gcode_macro _LIGHTS'].present %}
SET_GCODE_VARIABLE MACRO=_LIGHTS VARIABLE=present VALUE=True
_LIGHTS
{% endif %}
[gcode_macro _MOTION_END]
description: Motion sensor: no more motion, lights off after the timeout
gcode:
UPDATE_DELAYED_GCODE ID=_motion_timeout DURATION={printer['gcode_macro _LIGHTS'].timeout}
[delayed_gcode _motion_timeout] [delayed_gcode _motion_timeout]
gcode: gcode:
{% set printing = printer.print_stats.state == "printing" %} SET_GCODE_VARIABLE MACRO=_LIGHTS VARIABLE=present VALUE=False
_LIGHTS
# RESPOND MSG="AM312: Timeout reached, no motion" [gcode_macro _LIGHTS_ON]
description: Lights on as if someone walked by (print start and end, startup)
gcode:
_MOTION_START
{% if printer['gcode_button am312'].state == 'RELEASED' %}
_MOTION_END
{% endif %}
{% if printing %} [delayed_gcode _lights_startup]
# RESPOND MSG="AM312: Printing -> dim light to 10%" initial_duration: 2
SET_PIN PIN=caselight VALUE=0.1 gcode:
_LIGHTS_ON
[gcode_macro CASELIGHT]
description: Case light and nozzle LEDs: MODE=AUTO (motion sensor), ON [VALUE=0-1] or OFF; no MODE: show the mode
gcode:
{% set l = printer['gcode_macro _LIGHTS'] %}
{% set mode = params.MODE|default('')|lower %}
{% if mode == '' %}
RESPOND MSG="Case light: mode {l.mode}, {'someone near' if l.present else 'nobody near'}, value {printer['output_pin caselight'].value}"
{% elif mode not in ['auto', 'on', 'off'] %}
_ERROR MSG="CASELIGHT: MODE must be AUTO, ON or OFF"
{% else %} {% else %}
# RESPOND MSG="AM312: Idle -> light OFF" {% if 'VALUE' in params %}
SET_PIN PIN=caselight VALUE=0.0 SET_GCODE_VARIABLE MACRO=_LIGHTS VARIABLE=on_value VALUE={[[params.VALUE|float, 0.0]|max, 1.0]|min}
{% endif %}
SET_GCODE_VARIABLE MACRO=_LIGHTS VARIABLE=mode VALUE="'{mode}'"
_LIGHTS
{% endif %} {% endif %}
_set_nozzle_leds_off