LEDs: nozzle light follows the motion sensor, new logo status macro

The motion timeout switched the nozzle LEDs off during prints, motion
switched them off when idle or paused, the timeout counted from the first
movement, and every _status_* macro stopped the nozzle light.

- _LIGHTS sets case light and nozzle LEDs from presence, print state and
  CASELIGHT MODE=AUTO|ON|OFF; the timeout (60 s) starts at the sensor
  release
- _STATUS STATE=... replaces the _status_* macros; logo effects only
  cover the logo LEDs and use REPLACE=1
- heater gauge while heating, print progress, paused, error flash from
  _ERROR, part ready once the bed is cool, dim night mode when idle and
  nobody near, cleaning during BLOBIFIER_CLEAN
- removed unused effects and macros, 12 fps for the toolhead effects

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

macros/print/print_start_end.cfg

@@ -29,7 +29,7 @@ gcode:
     # Clear what an earlier print or error left on the display
     M117
 
-    _motion_detected
+    _LIGHTS_ON
 
     #SET_PIN PIN=caselight VALUE=1.00
     UPDATE_DELAYED_GCODE ID=_delayed_motors_off DURATION=0
@@ -48,7 +48,7 @@ gcode:
     M109 S150       ; wait until nozzle reaches 150  ; wait until nozzle reaches 0
     {% endif %}
 
-    _status_homing
+    _STATUS STATE=homing
     RESPOND MSG="homing"
     HOME
     RESPOND MSG="homing finished"
@@ -63,7 +63,7 @@ gcode:
     {% endif %}
     
     G1 X175 Y175 Z2 F1200
-    _status_heating
+    _STATUS STATE=heating_bed
     RESPOND MSG="heating"
     {% if target_bed > 0 %}
       M140 S{target_bed}     ; start bed heater
@@ -72,11 +72,14 @@ gcode:
       M190 S{target_bed}     ; wait on bed temperature
     {% endif %}
 
+    _STATUS STATE=homing
     HOME    
+    _STATUS STATE=leveling
     QUAD_GANTRY_LEVEL
     BLOBIFIER_CLEAN     ; call another macro to wipe nozzle if available
     G1 X175 Y175 Z5 F1200
     
+    _STATUS STATE=heating_extruder
     _HEAT_FOR_LOADED_LANE TOOL={initial_tool}   ; unload needs the loaded filament's temperature
     T{initial_tool} #PURGE_LENGTH=100 #Load Initial Tool
     M104 S{target_extruder}                    ; set extruder to print temp
@@ -89,6 +92,7 @@ gcode:
     BLOBIFIER_CLEAN     ; call another macro to wipe nozzle if available
     
     G1 X175 Y175 Z5 F1200
+    _STATUS STATE=heating_bed
     {% if target_chamber > 30 %}
       RESPOND MSG="waiting for chamber temperature"      
       M141 S{target_chamber}  
@@ -133,7 +137,7 @@ gcode:
 gcode:
     RESPOND MSG="print start macro continued"
 
-    _motion_detected
+    _LIGHTS_ON
 
     {% set target_extruder = params.EXTRUDER|int %}
 
@@ -145,14 +149,14 @@ gcode:
     HOME    
     BLOBIFIER_CLEAN     ; call another macro to wipe nozzle if available
 
-    _status_calibrating_z
+    _STATUS STATE=calibrating_z
     G28 Z METHOD=CONTACT CALIBRATE=1    ; calibrate z offset and beacon model hot
     
-    _status_leveling
+    _STATUS STATE=leveling
     RESPOND MSG="quad ganrty level"
     QUAD_GANTRY_LEVEL
     
-    _status_meshing
+    _STATUS STATE=meshing
     RESPOND MSG="meshing"
     BED_MESH_CALIBRATE RUNS=2           ; bed mesh in scan mode
 
@@ -161,10 +165,10 @@ gcode:
     M104 S150       ; set nozzle temp to 150
     M109 S150       ; wait until nozzle reaches 150  ; wait until nozzle reaches 0
     
-    _status_calibrating_z
+    _STATUS STATE=calibrating_z
     G28 Z METHOD=CONTACT CALIBRATE=1    ; calibrate z offset and beacon model hot
     
-    _status_heating
+    _STATUS STATE=heating_extruder
     M104 S{target_extruder}                    ; set extruder to print temp
     M109 S{target_extruder}                    ; wait for extruder temp
     BLOBIFIER_PARK                             ; over the bucket, then undo the retracts
@@ -209,7 +213,7 @@ gcode:
     # per-reading width compensation made the flow jump between 77 and 119%.
     # To use it again: SET_BDWIDTH NAME=fila_width_0 COMMAND=ENABLE_WIDTH
     
-    _status_printing
+    _STATUS STATE=printing
 
 
 [gcode_macro PRINT_END]
@@ -223,7 +227,7 @@ gcode:
     
     SAVE_GCODE_STATE NAME=STATE_PRINT_END
 
-    _motion_detected
+    _LIGHTS_ON
 
     M400                           ; wait for buffer to clear
     G92 E0                         ; zero the extruder
@@ -238,7 +242,7 @@ gcode:
     M107                                     ; turn off fan
 
     #SET_PIN PIN=caselight VALUE=0.03
-    _status_part_ready
+    _STATUS STATE=part_ready
 
     UPDATE_DELAYED_GCODE ID=_delayed_motors_off DURATION=3600