TOUCH_COMPARE: Beacon contact vs bd_pressure touch (extras/bdp_touch.py)

bd_pressure's endstop output is not wired, so BDP_TOUCH lowers the nozzle
in small steps and reads the force after each one, up to a force limit
(default 80) or 0.4 mm below the start, then lifts back. It reports the
threshold height and the zero-force height from a line fit and logs the
curve to klippy.log. TOUCH_COMPARE heats the nozzle to 150C, homes, and
alternates Beacon's contact probe with BDP_TOUCH at one spot, reporting
mean, spread and range of each and of the difference. Refuses while the
bdp_guard is armed or the sensor is in PA mode.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
mangavalkandClaude Opus 5.5 committed 2026-11-02 16:58:20 +01:00
1 parent 13e49e43c7
commit b16961dba3
4 files changed
+306

No files matched your search

+2
View File
@@ -49,6 +49,7 @@ everything below, grouped by topic. Comment out what you do not use there.
| `stealthburner_leds.cfg` | Stealthburner logo status (`_STATUS STATE=...`: heating and print progress as a filling logo, paused, error flash from `_ERROR`, part ready once the bed is cool, dim when idle and nobody is near) and the nozzle light | `led_effect`, `neopixel:bt_logo` and `rainbow_turtle` from AFC |
| **sensors/** | | |
| `motion_sensor.cfg` | PIR motion sensor: case light and nozzle LEDs on while someone is near (timeout from the last motion), `CASELIGHT MODE=AUTO\|ON\|OFF`; runs outside the G-code queue, so the lights also react during heat waits and AFC loads | `extras/motion_lights.py`, sensor on a pin, `[output_pin caselight]`, `leds/stealthburner_leds.cfg` |
| `touch_compare.cfg` | `[bdp_touch]`, `TOUCH_COMPARE [N=10] [X] [Y] [TEMP=150]`: nozzle to 150C, `HOME`, then N pairs of a Beacon contact probe and a bd_pressure touch at one spot; reports mean, spread and range of each and of the difference | `extras/bdp_touch.py` + bd_pressure load-check firmware, Beacon |
### Klipper modules (`extras/`)
@@ -58,6 +59,7 @@ everything below, grouped by topic. Comment out what you do not use there.
| `bdwidth_status.py` | exposes bdwidth's motion counter and width to macros (`present: False` with neutral values when no bdwidth is configured, so the macros also work without it), and keeps a USB dropout of bdwidth (port: usb) from shutting down Klipper: the read is retried every 10 s and the port reopened |
| `bdpressure_check.py` | bd_pressure load check (`BDP_CHECK_START/STOP/QUERY`). Needs the load-check firmware from the bd_pressure `load-check-extension` branch; on stock firmware it reports "not available" and does nothing. Also reports how many readings the last `PA_CALIBRATE` got (`pa_points`, `pa_distinct`), used to reject runs with a silent or stuck sensor. |
| `bdp_guard.py` | nozzle collision guard: while armed (`BDP_GUARD_ARM/DISARM/QUERY`) reads the bd_pressure force every 20 ms over I2C and, in stop mode, shuts Klipper down when it stays above the threshold. Reports reads, peak and errors per phase in the console and klippy.log. When it arms and finds the sensor still in PA mode (an emergency stop during `PA_CALIBRATE`; `FIRMWARE_RESTART` does not reset the sensor), it switches it to probe mode and takes a new zero first. Puts a lock on the sensor's I2C connection that `bdpressure.py` and `bdpressure_check.py` also go through (Klipper allows one I2C request at a time per device). Needs the load-check firmware. |
| `bdp_touch.py` | `BDP_TOUCH`: lowers the nozzle in 0.005 mm steps and reads the bd_pressure force after each step (its endstop output is not wired), up to a force limit (default 80) or 0.4 mm below the start, then lifts back; reports the height where the force reaches the threshold and the zero-force height from a line fit, and logs the whole curve to klippy.log. `_TOUCH_COMPARE`: alternates that with Beacon's contact probe. Refuses while the bdp_guard is armed or the sensor is in PA mode. Needs the load-check firmware. |
### Scripts (`scripts/`)