Add a bed check: warn about bumps and flatness, pause PRINT_START on a failure
BED_SCAN_CHECK levels, scans and warns, without heating or touching the bed. extras/mesh_check.py fits a smooth surface to the mesh and reports areas more than 0.03 mm from it, and a range over 0.30 mm. In PRINT_START a failed check pauses before the nozzle heats. Resume sets the print file back to the PRINT_START line (M26), so it runs again as normal file G-code. BED_CHECK_IGNORE lets the next failed check only warn. Tested on saved scans and rendered macros only, not yet on the printer. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
e540e40cf7
commit
99b7109b5b
7 files changed
+358
-5
No files matched your search
@@ -16,6 +16,9 @@
|
||||
# (the lane AFC was loading when a tool change failed, otherwise the loaded
|
||||
# lane), and RESUME stops with an error when another lane (or none) is loaded.
|
||||
# RESUME LANE_CHECK=0 resumes anyway (e.g. after remapping with SET_MAP).
|
||||
# A failed bed check in PRINT_START (calibration/bed_scan_check.cfg) pauses with
|
||||
# _BED_CHECK_STATE.pending set: PAUSE then only pauses, and RESUME runs
|
||||
# PRINT_START again instead of this chain's purge and lane check.
|
||||
|
||||
# https://klipperscreen.readthedocs.io/en/latest/macros/#recommended
|
||||
[gcode_macro PAUSE]
|
||||
@@ -25,7 +28,9 @@ variable_saved_fan_speed: 0.0
|
||||
variable_parked: False # set by PAUSE, used by _RESUME_PRINT
|
||||
variable_expected_lane: '' # AFC lane the print needs after RESUME ('' = no check)
|
||||
gcode:
|
||||
{% if not printer.pause_resume.is_paused %}
|
||||
{% if printer["gcode_macro _BED_CHECK_STATE"].pending %}
|
||||
PAUSE_BASE
|
||||
{% elif not printer.pause_resume.is_paused %}
|
||||
# AFC sets next_lane during a tool change and still has it when a failed
|
||||
# change pauses the print; it clears it once CHANGE_TOOL returns
|
||||
{% if 'AFC' in printer %}
|
||||
@@ -54,7 +59,11 @@ gcode:
|
||||
description: Resume the print (while HEAT_SOAK runs: skip the soak phase)
|
||||
rename_existing: RESUME_BASE
|
||||
gcode:
|
||||
HEAT_SOAK_RESUME ON_RESUME=_RESUME_PRINT {rawparams}
|
||||
{% if printer["gcode_macro _BED_CHECK_STATE"].pending %}
|
||||
_BED_CHECK_RETRY
|
||||
{% else %}
|
||||
HEAT_SOAK_RESUME ON_RESUME=_RESUME_PRINT {rawparams}
|
||||
{% endif %}
|
||||
|
||||
[gcode_macro _RESUME_PRINT]
|
||||
description: Resume after PAUSE: purge and check (or unretract), restore the part fan, continue the print
|
||||
|
||||
@@ -9,8 +9,10 @@
|
||||
# PRINT_START runs on a soaked bed:
|
||||
# PRINT_WARMUP bed heats while the nozzle cools and the printer homes,
|
||||
# wait for the bed, HEAT_SOAK
|
||||
# PRINT_START QGL, Z, contact Z calibration, mesh, load the initial tool,
|
||||
# PA for all lanes, XY reference
|
||||
# PRINT_START QGL, Z, contact Z calibration, mesh, bed check (a failed
|
||||
# check pauses, RESUME runs PRINT_START again, see
|
||||
# calibration/bed_scan_check.cfg), then _PRINT_START_FINISH:
|
||||
# load the initial tool, PA for all lanes, XY reference
|
||||
# The filament is loaded after the Z calibration, so the contact always
|
||||
# touches a clean nozzle that has not been oozing at 150C for minutes.
|
||||
# Chamber prints are the exception: PRINT_WARMUP loads and purges the first
|
||||
@@ -26,6 +28,7 @@ gcode:
|
||||
|
||||
RESET_FAILURE
|
||||
CLEAR_PAUSE
|
||||
_BED_CHECK_RESET
|
||||
# Clear what an earlier print or error left on the display
|
||||
M117
|
||||
|
||||
@@ -193,10 +196,14 @@ gcode:
|
||||
RESUME_BASE
|
||||
|
||||
[gcode_macro PRINT_START]
|
||||
description: Print start after HEAT_SOAK: QGL, Z calibration, mesh, load the initial tool, PA
|
||||
description: Print start after HEAT_SOAK: QGL, Z calibration, mesh, bed check, then _PRINT_START_FINISH
|
||||
gcode:
|
||||
{% set target_extruder = params.EXTRUDER|int %}
|
||||
{% set initial_tool = params.TOOL|default("0")|int %}
|
||||
# Rendered while this line of the print file runs: the start of the line,
|
||||
# where a retry after a failed bed check goes back to. -1: not from a file.
|
||||
{% set sd = printer.virtual_sdcard %}
|
||||
{% set file_pos = sd.file_position if sd.is_active else -1 %}
|
||||
|
||||
RESPOND MSG="print start macro continued"
|
||||
_LIGHTS_ON
|
||||
@@ -235,6 +242,35 @@ gcode:
|
||||
# From here on the nozzle extrudes and AFC cuts and loads: guard off
|
||||
_GUARD_OFF
|
||||
|
||||
BED_MESH_CHECK
|
||||
_PRINT_START_GATE EXTRUDER={target_extruder} TOOL={initial_tool} FILE_POS={file_pos}
|
||||
|
||||
# Separate macro: rendered after BED_MESH_CHECK has run. Pausing does not stop
|
||||
# a running macro, so what follows the check must not be in PRINT_START itself.
|
||||
[gcode_macro _PRINT_START_GATE]
|
||||
description: Helper for PRINT_START: pause when the bed check failed, else go on with _PRINT_START_FINISH
|
||||
gcode:
|
||||
{% set check = printer.mesh_check %}
|
||||
{% set ignore = printer["gcode_macro _BED_CHECK_STATE"].ignore %}
|
||||
{% set file_pos = params.FILE_POS|int %}
|
||||
{% if check.result == 'fail' and not ignore and file_pos >= 0 %}
|
||||
_BED_CHECK_PAUSE FILE_POS={file_pos}
|
||||
{% else %}
|
||||
{% if check.result == 'fail' %}
|
||||
_WARN MSG="Bed check failed, continuing: {check.summary}" DISPLAY="Bed check failed, continuing"
|
||||
{% elif check.result != 'ok' %}
|
||||
_WARN MSG="Bed check not done, continuing: {check.summary}" DISPLAY="Bed check not done"
|
||||
{% endif %}
|
||||
_BED_CHECK_RESET
|
||||
_PRINT_START_FINISH EXTRUDER={params.EXTRUDER} TOOL={params.TOOL}
|
||||
{% endif %}
|
||||
|
||||
[gcode_macro _PRINT_START_FINISH]
|
||||
description: Helper for PRINT_START after the bed check: load the initial tool, PA, XY reference
|
||||
gcode:
|
||||
{% set target_extruder = params.EXTRUDER|int %}
|
||||
{% set initial_tool = params.TOOL|default("0")|int %}
|
||||
|
||||
# Heat over the bucket, then undo the retracts of the previous PRINT_END
|
||||
_STATUS STATE=heating_extruder
|
||||
BLOBIFIER_PARK
|
||||
@@ -310,6 +346,7 @@ gcode:
|
||||
description: Heaters (incl. chamber heater) and part fan off, flow back to 100%, bdwidth off, mesh and skew cleared, nozzle guard off
|
||||
gcode:
|
||||
_GUARD_OFF ; a print start that failed while it was armed
|
||||
_BED_CHECK_RESET ; cancelled while the bed check had it paused
|
||||
TURN_OFF_HEATERS
|
||||
iHEATER_OFF ; stops the chamber heater control loop too
|
||||
M107
|
||||
|
||||
Reference in new issue
Block a user