Auto-resume after an AFC buffer fault pause
A NOT FEEDING / CLOG pause during a print runs RESUME by itself after 5 s, so the lane check and the purge check decide; a failed check keeps the print paused. At most 2 per print, none within 10 min of printing of the previous one, only between _PRINT_START_FINISH and the print end. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
bcb1a53b2a
commit
5e8743c33a
5 files changed
+119
-1
No files matched your search
@@ -39,6 +39,7 @@ everything below, grouped by topic. Comment out what you do not use there.
|
|||||||
| `lane_tools.cfg` | `LANE_FEED_UNTIL_HUB_OPEN`, `LANE_FEED_ABORT` | AFC |
|
| `lane_tools.cfg` | `LANE_FEED_UNTIL_HUB_OPEN`, `LANE_FEED_ABORT` | AFC |
|
||||||
| `purge_check.cfg` | `BLOBIFIER_CHECKED`: checks every AFC purge with bd_pressure (and optionally bdwidth motion); a bd_pressure that does not answer fails the check, `PURGE_CHECK_IGNORE_SENSOR` lets the current print finish without it; when the previous filament (saved `nozzle_last_temp`) needs more than 10°C above the new one, the purge runs at the previous filament's temperature and the nozzle cools back afterwards, so its leftover melts out | Blobifier, AFC, `bdpressure_check.py` from the bd_pressure repo + its load-check firmware, `extras/bdwidth_status.py` |
|
| `purge_check.cfg` | `BLOBIFIER_CHECKED`: checks every AFC purge with bd_pressure (and optionally bdwidth motion); a bd_pressure that does not answer fails the check, `PURGE_CHECK_IGNORE_SENSOR` lets the current print finish without it; when the previous filament (saved `nozzle_last_temp`) needs more than 10°C above the new one, the purge runs at the previous filament's temperature and the nozzle cools back afterwards, so its leftover melts out | Blobifier, AFC, `bdpressure_check.py` from the bd_pressure repo + its load-check firmware, `extras/bdwidth_status.py` |
|
||||||
| `flex_lanes.cfg` | Lanes holding TPU/TPE (material from Spoolman) get slower long moves (50 mm/s, AFC's minimum) through the tube; back to the configured speed when the lane holds something else. Polls every 5 s, reapplies after a restart. The last stretch into the extruder (`tool_load_speed`) stays as configured | AFC |
|
| `flex_lanes.cfg` | Lanes holding TPU/TPE (material from Spoolman) get slower long moves (50 mm/s, AFC's minimum) through the tube; back to the configured speed when the lane holds something else. Polls every 5 s, reapplies after a restart. The last stretch into the extruder (`tool_load_speed`) stays as configured | AFC |
|
||||||
|
| `auto_resume.cfg` | After an AFC buffer fault pause ("AFC NOT FEEDING", "CLOG DETECTED") during a print, runs `RESUME` by itself after 5 s, so the lane check and the purge check decide; a failed check keeps it paused. At most 2 per print and none within 10 min of printing after the previous one; not during `PRINT_START` or a PA test. Off: `enabled` in `_AUTO_RESUME_CFG` | `print/pause_resume.cfg`, `purge_check.cfg`, AFC |
|
||||||
| `purge_until_empty.cfg` | `PURGE_UNTIL_EMPTY`: purges a snapped filament out until there is no more nozzle pressure | same as `purge_check.cfg` |
|
| `purge_until_empty.cfg` | `PURGE_UNTIL_EMPTY`: purges a snapped filament out until there is no more nozzle pressure | same as `purge_check.cfg` |
|
||||||
| **pressure_advance/** | | |
|
| **pressure_advance/** | | |
|
||||||
| `bd_pressure.cfg` | `[bdpressure bd_pa]` (I2C on the Nitehawk) and the vendor macros `PA_CALIBRATE`, `PA_E`, `PA_RESET`, `PA_STATE`; `PA_CALIBRATE` no longer sets Z back to a value read before the test (wrong after a Z hop in `G28 XY`) | `bdpressure.py` from the bd_pressure repo |
|
| `bd_pressure.cfg` | `[bdpressure bd_pa]` (I2C on the Nitehawk) and the vendor macros `PA_CALIBRATE`, `PA_E`, `PA_RESET`, `PA_STATE`; `PA_CALIBRATE` no longer sets Z back to a value read before the test (wrong after a Z hop in `G28 XY`) | `bdpressure.py` from the bd_pressure repo |
|
||||||
|
|||||||
@@ -0,0 +1,99 @@
|
|||||||
|
# Automatic resume after an AFC buffer fault ("AFC NOT FEEDING" / "CLOG DETECTED")
|
||||||
|
#
|
||||||
|
# When AFC pauses a print because the buffer stayed empty or full too long,
|
||||||
|
# PAUSE (print/pause_resume.cfg) calls _AUTO_RESUME_ARM. After `delay` seconds
|
||||||
|
# _AUTO_RESUME runs the normal RESUME: AFC clears its error, the lane check
|
||||||
|
# runs, and _RESUME_PRINT purges into the Blobifier with the purge check. A
|
||||||
|
# failed check (or lane check) stops that RESUME as usual, so the print stays
|
||||||
|
# paused and waits for you.
|
||||||
|
#
|
||||||
|
# Limits, so a real problem (tangled spool, grinding extruder, clog) is not
|
||||||
|
# hidden: at most `max_per_print` automatic resumes per print, and none when
|
||||||
|
# the previous one was less than `min_interval` minutes of printing ago. After
|
||||||
|
# that the print stays paused like before.
|
||||||
|
#
|
||||||
|
# Only between _PRINT_START_FINISH and the end of the print (`active`): a pause
|
||||||
|
# during PRINT_START or a PA test needs CLEAR_PAUSE, not RESUME.
|
||||||
|
#
|
||||||
|
# Turn off: SET_GCODE_VARIABLE MACRO=_AUTO_RESUME_CFG VARIABLE=enabled VALUE=False
|
||||||
|
# (until the next restart; change `enabled` below to keep it off)
|
||||||
|
|
||||||
|
[gcode_macro _AUTO_RESUME_CFG]
|
||||||
|
description: Settings and state for the automatic resume after an AFC buffer fault
|
||||||
|
variable_enabled: True
|
||||||
|
variable_max_per_print: 2 # automatic resumes per print
|
||||||
|
variable_min_interval: 10 # minutes of printing since the previous automatic resume
|
||||||
|
variable_delay: 5 # seconds after the pause (AFC finishes its own pause first)
|
||||||
|
variable_faults: ['NOT FEEDING', 'CLOG DETECTED'] # text in AFC's error message
|
||||||
|
# State (set by the macros)
|
||||||
|
variable_active: False # True from _PRINT_START_FINISH to the end of the print
|
||||||
|
variable_count: 0 # automatic resumes in this print
|
||||||
|
variable_last_at: -1.0 # print_duration (s) of the last automatic resume, -1 = none
|
||||||
|
variable_pending: '' # fault the timer is waiting to resume from
|
||||||
|
gcode:
|
||||||
|
RESPOND MSG="Auto-resume: {'on' if enabled else 'off'}, {'active' if active else 'not active'}, {count}/{max_per_print} used in this print"
|
||||||
|
|
||||||
|
# Called by _PRINT_START_FINISH (ON=1) and _PRINT_CLEANUP (ON=0)
|
||||||
|
[gcode_macro _AUTO_RESUME_ACTIVE]
|
||||||
|
description: Start (ON=1) or end (ON=0) the automatic resume for a print
|
||||||
|
gcode:
|
||||||
|
{% set on = params.ON|default(1)|int %}
|
||||||
|
SET_GCODE_VARIABLE MACRO=_AUTO_RESUME_CFG VARIABLE=active VALUE={True if on else False}
|
||||||
|
SET_GCODE_VARIABLE MACRO=_AUTO_RESUME_CFG VARIABLE=count VALUE=0
|
||||||
|
SET_GCODE_VARIABLE MACRO=_AUTO_RESUME_CFG VARIABLE=last_at VALUE=-1.0
|
||||||
|
SET_GCODE_VARIABLE MACRO=_AUTO_RESUME_CFG VARIABLE=pending VALUE="''"
|
||||||
|
UPDATE_DELAYED_GCODE ID=_AUTO_RESUME DURATION=0
|
||||||
|
{% if on and 'AFC' in printer %}
|
||||||
|
# Old messages would be read as this print's fault: start empty
|
||||||
|
AFC_CLEAR_ALL_MESSAGES
|
||||||
|
{% endif %}
|
||||||
|
|
||||||
|
# Called by PAUSE when it pauses a print. AFC's message queue shows its oldest
|
||||||
|
# message first; _RESUME_PRINT removes a buffer fault message once resumed, so
|
||||||
|
# the oldest one is this pause's.
|
||||||
|
[gcode_macro _AUTO_RESUME_ARM]
|
||||||
|
description: Start the automatic resume timer when AFC paused for a buffer fault and the limits allow it
|
||||||
|
gcode:
|
||||||
|
{% set cfg = printer["gcode_macro _AUTO_RESUME_CFG"] %}
|
||||||
|
{% set has_afc = 'AFC' in printer %}
|
||||||
|
{% set msg = printer.AFC.message.message|default('') if has_afc else '' %}
|
||||||
|
{% set fault = (cfg.faults|select('in', msg)|list + [''])[0] %}
|
||||||
|
{% set now = printer.print_stats.print_duration|float %}
|
||||||
|
{% if cfg.enabled and cfg.active and has_afc and printer.AFC.error_state and fault %}
|
||||||
|
{% if cfg.count >= cfg.max_per_print %}
|
||||||
|
_WARN MSG="Auto-resume: not resuming after AFC {fault}, already {cfg.count} automatic resumes in this print. Check the lane, then RESUME." DISPLAY="AFC {fault}: check, then RESUME"
|
||||||
|
{% elif cfg.last_at >= 0 and now - cfg.last_at < cfg.min_interval * 60 %}
|
||||||
|
_WARN MSG="Auto-resume: not resuming after AFC {fault}, the last automatic resume was only {((now - cfg.last_at) / 60)|round(1)} min of printing ago. Check the lane, then RESUME." DISPLAY="AFC {fault} again: check, then RESUME"
|
||||||
|
{% else %}
|
||||||
|
SET_GCODE_VARIABLE MACRO=_AUTO_RESUME_CFG VARIABLE=pending VALUE="'{fault}'"
|
||||||
|
RESPOND MSG="Auto-resume: AFC {fault}, resuming in {cfg.delay} s with the purge check ({cfg.count + 1}/{cfg.max_per_print})"
|
||||||
|
UPDATE_DELAYED_GCODE ID=_AUTO_RESUME DURATION={cfg.delay}
|
||||||
|
{% endif %}
|
||||||
|
{% endif %}
|
||||||
|
|
||||||
|
[delayed_gcode _AUTO_RESUME]
|
||||||
|
gcode:
|
||||||
|
{% set cfg = printer["gcode_macro _AUTO_RESUME_CFG"] %}
|
||||||
|
{% set fault = cfg.pending %}
|
||||||
|
SET_GCODE_VARIABLE MACRO=_AUTO_RESUME_CFG VARIABLE=pending VALUE="''"
|
||||||
|
# Only when nothing changed since the pause: still paused, still AFC's
|
||||||
|
# error (a manual RESUME or CANCEL in the meantime ends it)
|
||||||
|
{% if fault and cfg.active and printer.print_stats.state == 'paused'
|
||||||
|
and printer.pause_resume.is_paused and printer.AFC.error_state %}
|
||||||
|
SET_GCODE_VARIABLE MACRO=_AUTO_RESUME_CFG VARIABLE=count VALUE={cfg.count + 1}
|
||||||
|
SET_GCODE_VARIABLE MACRO=_AUTO_RESUME_CFG VARIABLE=last_at VALUE={printer.print_stats.print_duration|float}
|
||||||
|
RESPOND MSG="Auto-resume {cfg.count + 1}/{cfg.max_per_print} after AFC {fault}"
|
||||||
|
M117 Auto-resume {cfg.count + 1}/{cfg.max_per_print}: AFC {fault}
|
||||||
|
RESUME
|
||||||
|
{% endif %}
|
||||||
|
|
||||||
|
# Called by _RESUME_PRINT after a resume: remove a buffer fault message from
|
||||||
|
# the front of AFC's queue, so the next pause reads its own message
|
||||||
|
[gcode_macro _AUTO_RESUME_CLEAR_FAULT]
|
||||||
|
description: Helper: drop AFC's buffer fault message after a resume
|
||||||
|
gcode:
|
||||||
|
{% set cfg = printer["gcode_macro _AUTO_RESUME_CFG"] %}
|
||||||
|
{% set msg = printer.AFC.message.message|default('') if 'AFC' in printer else '' %}
|
||||||
|
{% if msg and cfg.faults|select('in', msg)|list %}
|
||||||
|
AFC_CLEAR_MESSAGE
|
||||||
|
{% endif %}
|
||||||
@@ -37,6 +37,7 @@
|
|||||||
[include afc/xy_safety_check.cfg]
|
[include afc/xy_safety_check.cfg]
|
||||||
[include afc/lane_tools.cfg]
|
[include afc/lane_tools.cfg]
|
||||||
[include afc/purge_check.cfg]
|
[include afc/purge_check.cfg]
|
||||||
|
[include afc/auto_resume.cfg] # resume by itself after an AFC buffer fault (purge check first, limited)
|
||||||
[include afc/purge_until_empty.cfg]
|
[include afc/purge_until_empty.cfg]
|
||||||
[include afc/flex_lanes.cfg] # TPU/TPE lanes: slower long moves
|
[include afc/flex_lanes.cfg] # TPU/TPE lanes: slower long moves
|
||||||
|
|
||||||
|
|||||||
@@ -16,6 +16,9 @@
|
|||||||
# (the lane AFC was loading when a tool change failed, otherwise the loaded
|
# (the lane AFC was loading when a tool change failed, otherwise the loaded
|
||||||
# lane), and RESUME stops with an error when another lane (or none) is loaded.
|
# lane), and RESUME stops with an error when another lane (or none) is loaded.
|
||||||
# RESUME LANE_CHECK=0 resumes anyway (e.g. after remapping with SET_MAP).
|
# RESUME LANE_CHECK=0 resumes anyway (e.g. after remapping with SET_MAP).
|
||||||
|
# An AFC buffer fault pause ("AFC NOT FEEDING" / "CLOG DETECTED") during a
|
||||||
|
# print runs this RESUME by itself after a few seconds, within limits
|
||||||
|
# (afc/auto_resume.cfg).
|
||||||
# A failed bed check in PRINT_START (calibration/bed_scan_check.cfg) pauses with
|
# A failed bed check in PRINT_START (calibration/bed_scan_check.cfg) pauses with
|
||||||
# _BED_CHECK_STATE.pending set: PAUSE then only pauses, and RESUME runs
|
# _BED_CHECK_STATE.pending set: PAUSE then only pauses, and RESUME runs
|
||||||
# PRINT_START again instead of this chain's purge and lane check.
|
# PRINT_START again instead of this chain's purge and lane check.
|
||||||
@@ -51,6 +54,9 @@ gcode:
|
|||||||
_STATUS STATE=paused
|
_STATUS STATE=paused
|
||||||
# Set fan to S28 (28/255 ≈ 0.1098)
|
# Set fan to S28 (28/255 ≈ 0.1098)
|
||||||
M106 S28
|
M106 S28
|
||||||
|
{% if 'gcode_macro _AUTO_RESUME_ARM' in printer %}
|
||||||
|
_AUTO_RESUME_ARM ; AFC buffer fault: resume by itself after the purge check (afc/auto_resume.cfg)
|
||||||
|
{% endif %}
|
||||||
{% else %}
|
{% else %}
|
||||||
PAUSE_BASE
|
PAUSE_BASE
|
||||||
{% endif %}
|
{% endif %}
|
||||||
@@ -103,6 +109,9 @@ gcode:
|
|||||||
{% endif %}
|
{% endif %}
|
||||||
SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=parked VALUE=False
|
SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=parked VALUE=False
|
||||||
SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=expected_lane VALUE="''"
|
SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=expected_lane VALUE="''"
|
||||||
|
{% if 'gcode_macro _AUTO_RESUME_CLEAR_FAULT' in printer %}
|
||||||
|
_AUTO_RESUME_CLEAR_FAULT
|
||||||
|
{% endif %}
|
||||||
# Clear the pause reason from the display (no comment on an M117 line: it would show)
|
# Clear the pause reason from the display (no comment on an M117 line: it would show)
|
||||||
M117
|
M117
|
||||||
{% endif %}
|
{% endif %}
|
||||||
|
|||||||
@@ -306,6 +306,11 @@ gcode:
|
|||||||
# ("AFC NOT FEEDING"); the slicer switches it back at layer 2
|
# ("AFC NOT FEEDING"); the slicer switches it back at layer 2
|
||||||
_FIRST_LAYER_FAULT_DETECTION ON=1
|
_FIRST_LAYER_FAULT_DETECTION ON=1
|
||||||
|
|
||||||
|
# From here on an AFC buffer fault pause resumes by itself (afc/auto_resume.cfg)
|
||||||
|
{% if 'gcode_macro _AUTO_RESUME_ACTIVE' in printer %}
|
||||||
|
_AUTO_RESUME_ACTIVE ON=1
|
||||||
|
{% endif %}
|
||||||
|
|
||||||
RESPOND MSG="starting"
|
RESPOND MSG="starting"
|
||||||
_STATUS STATE=printing
|
_STATUS STATE=printing
|
||||||
|
|
||||||
@@ -346,7 +351,7 @@ gcode:
|
|||||||
|
|
||||||
# End-of-print cleanup shared by PRINT_END and CANCEL_PRINT
|
# End-of-print cleanup shared by PRINT_END and CANCEL_PRINT
|
||||||
[gcode_macro _PRINT_CLEANUP]
|
[gcode_macro _PRINT_CLEANUP]
|
||||||
description: Heaters (incl. chamber heater) and part fan off, flow back to 100%, bdwidth off, mesh and skew cleared, nozzle guard off, AFC runouts cleared
|
description: Heaters (incl. chamber heater) and part fan off, flow back to 100%, bdwidth off, mesh and skew cleared, nozzle guard off, AFC runouts cleared, auto-resume off
|
||||||
gcode:
|
gcode:
|
||||||
_GUARD_OFF ; a print start that failed while it was armed
|
_GUARD_OFF ; a print start that failed while it was armed
|
||||||
_BED_CHECK_RESET ; cancelled while the bed check had it paused
|
_BED_CHECK_RESET ; cancelled while the bed check had it paused
|
||||||
@@ -364,6 +369,9 @@ gcode:
|
|||||||
SET_GCODE_VARIABLE MACRO=_PURGE_CHECK_CFG VARIABLE=ignore_missing_sensor VALUE=False
|
SET_GCODE_VARIABLE MACRO=_PURGE_CHECK_CFG VARIABLE=ignore_missing_sensor VALUE=False
|
||||||
{% endif %}
|
{% endif %}
|
||||||
_FIRST_LAYER_FAULT_DETECTION ON=0 ; a print that ended during the first layer
|
_FIRST_LAYER_FAULT_DETECTION ON=0 ; a print that ended during the first layer
|
||||||
|
{% if 'gcode_macro _AUTO_RESUME_ACTIVE' in printer %}
|
||||||
|
_AUTO_RESUME_ACTIVE ON=0 ; also stops a pending automatic resume
|
||||||
|
{% endif %}
|
||||||
# Infinite spool is set up per print (SET_RUNOUT): clear every lane's runout
|
# Infinite spool is set up per print (SET_RUNOUT): clear every lane's runout
|
||||||
{% if 'AFC' in printer %}
|
{% if 'AFC' in printer %}
|
||||||
{% for lane in printer.AFC.lanes|default([]) if printer["AFC_stepper " ~ lane].runout_lane|default(none) %}
|
{% for lane in printer.AFC.lanes|default([]) if printer["AFC_stepper " ~ lane].runout_lane|default(none) %}
|
||||||
|
|||||||
Reference in new issue
Block a user