Auto-resume after an AFC buffer fault pause
A NOT FEEDING / CLOG pause during a print runs RESUME by itself after 5 s, so the lane check and the purge check decide; a failed check keeps the print paused. At most 2 per print, none within 10 min of printing of the previous one, only between _PRINT_START_FINISH and the print end. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
bcb1a53b2a
commit
5e8743c33a
5 files changed
+119
-1
No files matched your search
@@ -16,6 +16,9 @@
|
||||
# (the lane AFC was loading when a tool change failed, otherwise the loaded
|
||||
# lane), and RESUME stops with an error when another lane (or none) is loaded.
|
||||
# RESUME LANE_CHECK=0 resumes anyway (e.g. after remapping with SET_MAP).
|
||||
# An AFC buffer fault pause ("AFC NOT FEEDING" / "CLOG DETECTED") during a
|
||||
# print runs this RESUME by itself after a few seconds, within limits
|
||||
# (afc/auto_resume.cfg).
|
||||
# A failed bed check in PRINT_START (calibration/bed_scan_check.cfg) pauses with
|
||||
# _BED_CHECK_STATE.pending set: PAUSE then only pauses, and RESUME runs
|
||||
# PRINT_START again instead of this chain's purge and lane check.
|
||||
@@ -51,6 +54,9 @@ gcode:
|
||||
_STATUS STATE=paused
|
||||
# Set fan to S28 (28/255 ≈ 0.1098)
|
||||
M106 S28
|
||||
{% if 'gcode_macro _AUTO_RESUME_ARM' in printer %}
|
||||
_AUTO_RESUME_ARM ; AFC buffer fault: resume by itself after the purge check (afc/auto_resume.cfg)
|
||||
{% endif %}
|
||||
{% else %}
|
||||
PAUSE_BASE
|
||||
{% endif %}
|
||||
@@ -103,6 +109,9 @@ gcode:
|
||||
{% endif %}
|
||||
SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=parked VALUE=False
|
||||
SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=expected_lane VALUE="''"
|
||||
{% if 'gcode_macro _AUTO_RESUME_CLEAR_FAULT' in printer %}
|
||||
_AUTO_RESUME_CLEAR_FAULT
|
||||
{% endif %}
|
||||
# Clear the pause reason from the display (no comment on an M117 line: it would show)
|
||||
M117
|
||||
{% endif %}
|
||||
|
||||
@@ -306,6 +306,11 @@ gcode:
|
||||
# ("AFC NOT FEEDING"); the slicer switches it back at layer 2
|
||||
_FIRST_LAYER_FAULT_DETECTION ON=1
|
||||
|
||||
# From here on an AFC buffer fault pause resumes by itself (afc/auto_resume.cfg)
|
||||
{% if 'gcode_macro _AUTO_RESUME_ACTIVE' in printer %}
|
||||
_AUTO_RESUME_ACTIVE ON=1
|
||||
{% endif %}
|
||||
|
||||
RESPOND MSG="starting"
|
||||
_STATUS STATE=printing
|
||||
|
||||
@@ -346,7 +351,7 @@ gcode:
|
||||
|
||||
# End-of-print cleanup shared by PRINT_END and CANCEL_PRINT
|
||||
[gcode_macro _PRINT_CLEANUP]
|
||||
description: Heaters (incl. chamber heater) and part fan off, flow back to 100%, bdwidth off, mesh and skew cleared, nozzle guard off, AFC runouts cleared
|
||||
description: Heaters (incl. chamber heater) and part fan off, flow back to 100%, bdwidth off, mesh and skew cleared, nozzle guard off, AFC runouts cleared, auto-resume off
|
||||
gcode:
|
||||
_GUARD_OFF ; a print start that failed while it was armed
|
||||
_BED_CHECK_RESET ; cancelled while the bed check had it paused
|
||||
@@ -364,6 +369,9 @@ gcode:
|
||||
SET_GCODE_VARIABLE MACRO=_PURGE_CHECK_CFG VARIABLE=ignore_missing_sensor VALUE=False
|
||||
{% endif %}
|
||||
_FIRST_LAYER_FAULT_DETECTION ON=0 ; a print that ended during the first layer
|
||||
{% if 'gcode_macro _AUTO_RESUME_ACTIVE' in printer %}
|
||||
_AUTO_RESUME_ACTIVE ON=0 ; also stops a pending automatic resume
|
||||
{% endif %}
|
||||
# Infinite spool is set up per print (SET_RUNOUT): clear every lane's runout
|
||||
{% if 'AFC' in printer %}
|
||||
{% for lane in printer.AFC.lanes|default([]) if printer["AFC_stepper " ~ lane].runout_lane|default(none) %}
|
||||
|
||||
Reference in new issue
Block a user