SpoolSense UPDATE_TAG also on a cancelled print
Moved from PRINT_END to _PRINT_CLEANUP, which PRINT_END and CANCEL_PRINT both run, so a cancelled print's filament is deducted too. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
d51d791a10
commit
385adb5283
1 file changed
+7
-7
@@ -348,16 +348,10 @@ gcode:
|
|||||||
RESTORE_GCODE_STATE NAME=STATE_PRINT_END
|
RESTORE_GCODE_STATE NAME=STATE_PRINT_END
|
||||||
# After the restore: RESTORE_GCODE_STATE also restores the flow (M221)
|
# After the restore: RESTORE_GCODE_STATE also restores the flow (M221)
|
||||||
_PRINT_CLEANUP
|
_PRINT_CLEANUP
|
||||||
# SpoolSense (spoolsense.cfg in the config folder, not in this repo): the
|
|
||||||
# middleware deducts this print's filament and writes it to the spool's
|
|
||||||
# NFC tag at its next scan
|
|
||||||
{% if 'gcode_macro UPDATE_TAG' in printer %}
|
|
||||||
UPDATE_TAG
|
|
||||||
{% endif %}
|
|
||||||
|
|
||||||
# End-of-print cleanup shared by PRINT_END and CANCEL_PRINT
|
# End-of-print cleanup shared by PRINT_END and CANCEL_PRINT
|
||||||
[gcode_macro _PRINT_CLEANUP]
|
[gcode_macro _PRINT_CLEANUP]
|
||||||
description: Heaters (incl. chamber heater) and part fan off, flow back to 100%, bdwidth off, mesh and skew cleared, nozzle guard off, AFC runouts cleared, auto-resume off
|
description: Heaters (incl. chamber heater) and part fan off, flow back to 100%, bdwidth off, mesh and skew cleared, nozzle guard off, AFC runouts cleared, auto-resume off, SpoolSense tag update
|
||||||
gcode:
|
gcode:
|
||||||
_GUARD_OFF ; a print start that failed while it was armed
|
_GUARD_OFF ; a print start that failed while it was armed
|
||||||
_BED_CHECK_RESET ; cancelled while the bed check had it paused
|
_BED_CHECK_RESET ; cancelled while the bed check had it paused
|
||||||
@@ -384,6 +378,12 @@ gcode:
|
|||||||
SET_RUNOUT LANE={lane} RUNOUT=NONE
|
SET_RUNOUT LANE={lane} RUNOUT=NONE
|
||||||
{% endfor %}
|
{% endfor %}
|
||||||
{% endif %}
|
{% endif %}
|
||||||
|
# SpoolSense (spoolsense.cfg in the config folder, not in this repo): the
|
||||||
|
# middleware deducts the filament of this print (also a cancelled one) and
|
||||||
|
# writes it to the spool's NFC tag at its next scan
|
||||||
|
{% if 'gcode_macro UPDATE_TAG' in printer %}
|
||||||
|
UPDATE_TAG
|
||||||
|
{% endif %}
|
||||||
|
|
||||||
# AFC buffer fault detection (filament_error_sensitivity, 0-10, higher =
|
# AFC buffer fault detection (filament_error_sensitivity, 0-10, higher =
|
||||||
# pauses sooner) with its own value during the first layer.
|
# pauses sooner) with its own value during the first layer.
|
||||||
|
|||||||
Reference in new issue
Block a user