BDP_TOUCH: default STOP 60
At 2.2 force per 0.01 mm (measured 2026-11-02) the old default of 80 was out of reach within FLOOR from Z0.15 (peak 70 at -0.35); 60 is reached at about 0.27 mm into the bed and still leaves ~100 readings for the fit. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
7761e8f803
commit
2c1fd27dc6
3 files changed
+13
-11
No files matched your search
+10
-8
@@ -24,12 +24,14 @@
|
||||
# the TOUCH_COMPARE macro (macros/sensors/touch_compare.cfg), which heats
|
||||
# the nozzle and homes first.
|
||||
#
|
||||
# Safety: the move stops when the force reaches STOP (default 80, about
|
||||
# 0.3 mm into the bed; a purge peaks at 64-246) and overshoots by what was
|
||||
# already queued (at most ~0.15 s of the move, ~0.05 mm at 0.3 mm/s). The
|
||||
# descent ends at FLOOR below the start, and the nozzle always goes back up
|
||||
# to the start height, also after an error. It refuses to run while the bdp_guard is armed (in stop
|
||||
# mode the touch would shut Klipper down) or while the sensor is in PA mode.
|
||||
# Safety: the move stops when the force reaches STOP (default 60, about
|
||||
# 0.27 mm into the bed at 2.2 per 0.01 mm; 80 was out of reach within
|
||||
# FLOOR from Z0.15: peak 70 at -0.35; a purge peaks at 64-246) and
|
||||
# overshoots by what was already queued (at most ~0.15 s of the move,
|
||||
# ~0.05 mm at 0.3 mm/s). The descent ends at FLOOR below the start, and
|
||||
# the nozzle always goes back up to the start height, also after an error.
|
||||
# It refuses to run while the bdp_guard is armed (in stop mode the touch
|
||||
# would shut Klipper down) or while the sensor is in PA mode.
|
||||
#
|
||||
# Install: copy to ~/klipper/klippy/extras/bdp_touch.py (install.sh links
|
||||
# it) and add
|
||||
@@ -38,7 +40,7 @@
|
||||
# sensor: bd_pa # name after "bdpressure" in [bdpressure bd_pa]
|
||||
#
|
||||
# Commands:
|
||||
# BDP_TOUCH [THRESHOLD=15] [STOP=80] [SPEED=0.3] [FLOOR=0.5]
|
||||
# BDP_TOUCH [THRESHOLD=15] [STOP=60] [SPEED=0.3] [FLOOR=0.5]
|
||||
# touch at the current X/Y, starting at the current Z (SPEED in mm/s)
|
||||
# _TOUCH_COMPARE [N=10] [START=0.1] [THRESHOLD=..] [STOP=..] [SPEED=..]
|
||||
# the comparison loop; START is the BDP_TOUCH start height above the
|
||||
@@ -263,7 +265,7 @@ class BDPTouch:
|
||||
def _touch_params(self, gcmd):
|
||||
return dict(
|
||||
threshold=gcmd.get_float('THRESHOLD', 15., above=0.),
|
||||
stop=gcmd.get_float('STOP', 80., above=0., maxval=150.),
|
||||
stop=gcmd.get_float('STOP', 60., above=0., maxval=150.),
|
||||
speed=gcmd.get_float('SPEED', 0.3, minval=0.05, maxval=1.),
|
||||
floor=gcmd.get_float('FLOOR', 0.5, above=0., maxval=1.))
|
||||
|
||||
|
||||
Reference in new issue
Block a user