Bed fans off during prints without a heated chamber, remove unused bed PID
With the chamber open the bed fans only blow room air past the bed. PRINT_WARMUP sets print_fans_off for CHAMBER 30 or less, _PRINT_CLEANUP clears it. Chamber prints, the cooldown and heating the bed outside a print are unchanged. The PID values in PRINT_WARMUP never took effect: the SET_HEATER_TEMPERATURE override in bed_fans.cfg only passes on the target. The bed keeps its config values; the misleading console messages are gone. Tested with rendered macros only, not yet on the printer. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
99b7109b5b
commit
1dcbc50bf6
3 files changed
+20
-13
No files matched your search
@@ -31,7 +31,7 @@ everything below, grouped by topic. Comment out what you do not use there.
|
|||||||
| **heating/** | | |
|
| **heating/** | | |
|
||||||
| `heat_soak.cfg` | `HEAT_SOAK`, `STOP_HEAT_SOAK`, `CANCEL_HEAT_SOAK`, `HEAT_SOAK_RESUME`, `RESUME` | — |
|
| `heat_soak.cfg` | `HEAT_SOAK`, `STOP_HEAT_SOAK`, `CANCEL_HEAT_SOAK`, `HEAT_SOAK_RESUME`, `RESUME` | — |
|
||||||
| `soak_my_bed.cfg` | `SOAK_MY_BED` (homes and levels first) | soak-my-bed |
|
| `soak_my_bed.cfg` | `SOAK_MY_BED` (homes and levels first) | soak-my-bed |
|
||||||
| `bed_fans.cfg` | Bed fans through `SET_HEATER_TEMPERATURE`/`M190`/`M140`/`TURN_OFF_HEATERS` overrides | `[fan_generic BedFans]` |
|
| `bed_fans.cfg` | Bed fans through `SET_HEATER_TEMPERATURE`/`M190`/`M140`/`TURN_OFF_HEATERS` overrides; off during a print without a heated chamber (`PRINT_WARMUP CHAMBER=` 30 or less), on during the cooldown after any print | `[fan_generic BedFans]` |
|
||||||
| `chamber_iheater.cfg` | iHeater MCU, heater and sensors, `M141`, `M191`, `iHEATER_ON`, `iHEATER_OFF` | iHeater chamber heater |
|
| `chamber_iheater.cfg` | iHeater MCU, heater and sensors, `M141`, `M191`, `iHEATER_ON`, `iHEATER_OFF` | iHeater chamber heater |
|
||||||
| `filament_drying.cfg` | `START_DRYING`, `STOP_DRYING`, `STATUS_DRYING` | bed fans, chamber heater (optional) |
|
| `filament_drying.cfg` | `START_DRYING`, `STOP_DRYING`, `STATUS_DRYING` | bed fans, chamber heater (optional) |
|
||||||
| **afc/** | | |
|
| **afc/** | | |
|
||||||
|
|||||||
@@ -1,4 +1,9 @@
|
|||||||
# Bed fans driven by the bed heater (based on Ellis' bed fan macros)
|
# Bed fans driven by the bed heater (based on Ellis' bed fan macros)
|
||||||
|
#
|
||||||
|
# During a print without a heated chamber the fans stay off while the bed heats,
|
||||||
|
# soaks and prints: with the chamber open they only blow room air past the bed.
|
||||||
|
# PRINT_WARMUP sets print_fans_off, _PRINT_CLEANUP clears it. The cooldown after
|
||||||
|
# the print and heating the bed outside a print are not affected.
|
||||||
|
|
||||||
############### Config options ##################
|
############### Config options ##################
|
||||||
|
|
||||||
@@ -7,6 +12,7 @@ variable_threshold: 50 # If bed temp target is above this threshold, fans will
|
|||||||
variable_fast: 1.0 # Fan speed once bed temp is reached
|
variable_fast: 1.0 # Fan speed once bed temp is reached
|
||||||
variable_slow: 0.5 # Fan speed while bed is heating
|
variable_slow: 0.5 # Fan speed while bed is heating
|
||||||
variable_cooldown_temp: 40 # NEW: fans stop below this temp
|
variable_cooldown_temp: 40 # NEW: fans stop below this temp
|
||||||
|
variable_print_fans_off: False # set by PRINT_WARMUP for a print without a heated chamber
|
||||||
gcode:
|
gcode:
|
||||||
|
|
||||||
########## Aliases #########
|
########## Aliases #########
|
||||||
@@ -41,6 +47,7 @@ gcode:
|
|||||||
# Vars
|
# Vars
|
||||||
{% set THRESHOLD = printer["gcode_macro _BEDFANVARS"].threshold|int %}
|
{% set THRESHOLD = printer["gcode_macro _BEDFANVARS"].threshold|int %}
|
||||||
{% set COOLDOWN = printer["gcode_macro _BEDFANVARS"].cooldown_temp|int %}
|
{% set COOLDOWN = printer["gcode_macro _BEDFANVARS"].cooldown_temp|int %}
|
||||||
|
{% set FANS_OFF = printer["gcode_macro _BEDFANVARS"].print_fans_off %}
|
||||||
|
|
||||||
{% if HEATER|lower == "extruder" %}
|
{% if HEATER|lower == "extruder" %}
|
||||||
M104 S{TARGET}
|
M104 S{TARGET}
|
||||||
@@ -67,13 +74,13 @@ gcode:
|
|||||||
# Stop normal heating loop if running
|
# Stop normal heating loop if running
|
||||||
UPDATE_DELAYED_GCODE ID=bedfanloop DURATION=0
|
UPDATE_DELAYED_GCODE ID=bedfanloop DURATION=0
|
||||||
|
|
||||||
{% elif TARGET >= THRESHOLD %}
|
{% elif TARGET >= THRESHOLD and not FANS_OFF %}
|
||||||
# Heating above threshold
|
# Heating above threshold
|
||||||
BEDFANSSLOW
|
BEDFANSSLOW
|
||||||
UPDATE_DELAYED_GCODE ID=bedfanloop DURATION=1
|
UPDATE_DELAYED_GCODE ID=bedfanloop DURATION=1
|
||||||
|
|
||||||
{% else %}
|
{% else %}
|
||||||
# Low temp request
|
# Low temp request, or a print without a heated chamber
|
||||||
BEDFANSOFF
|
BEDFANSOFF
|
||||||
UPDATE_DELAYED_GCODE ID=bedfanloop DURATION=0
|
UPDATE_DELAYED_GCODE ID=bedfanloop DURATION=0
|
||||||
{% endif %}
|
{% endif %}
|
||||||
@@ -93,8 +100,9 @@ gcode:
|
|||||||
{% set S = params.S|int %}
|
{% set S = params.S|int %}
|
||||||
# Vars
|
# Vars
|
||||||
{% set THRESHOLD = printer["gcode_macro _BEDFANVARS"].threshold|int %}
|
{% set THRESHOLD = printer["gcode_macro _BEDFANVARS"].threshold|int %}
|
||||||
|
{% set FANS_ON = S >= THRESHOLD and not printer["gcode_macro _BEDFANVARS"].print_fans_off %}
|
||||||
|
|
||||||
{% if S >= THRESHOLD %}
|
{% if FANS_ON %}
|
||||||
BEDFANSSLOW # >= Threshold temp: Low speed fans while heating
|
BEDFANSSLOW # >= Threshold temp: Low speed fans while heating
|
||||||
{% else %}
|
{% else %}
|
||||||
BEDFANSOFF # < Threshold temp: Turn bed fans off
|
BEDFANSOFF # < Threshold temp: Turn bed fans off
|
||||||
@@ -109,7 +117,7 @@ gcode:
|
|||||||
{% endif %}
|
{% endif %}
|
||||||
|
|
||||||
# Post-heating fan speeds
|
# Post-heating fan speeds
|
||||||
{% if S >= THRESHOLD %}
|
{% if FANS_ON %}
|
||||||
BEDFANSFAST # >= Threshold temp: Higher speed fans after heating finished
|
BEDFANSFAST # >= Threshold temp: Higher speed fans after heating finished
|
||||||
{% endif %}
|
{% endif %}
|
||||||
|
|
||||||
@@ -152,7 +160,7 @@ gcode:
|
|||||||
# Vars
|
# Vars
|
||||||
{% set THRESHOLD = printer["gcode_macro _BEDFANVARS"].threshold|int %}
|
{% set THRESHOLD = printer["gcode_macro _BEDFANVARS"].threshold|int %}
|
||||||
|
|
||||||
{% if printer.heater_bed.target >= THRESHOLD %} # Continue only if target temp greater than threshold.
|
{% if printer.heater_bed.target >= THRESHOLD and not printer["gcode_macro _BEDFANVARS"].print_fans_off %} # Continue only if target temp greater than threshold.
|
||||||
{% if printer.heater_bed.temperature|int >= (printer.heater_bed.target|int - 1) %}
|
{% if printer.heater_bed.temperature|int >= (printer.heater_bed.target|int - 1) %}
|
||||||
BEDFANSFAST # If within 1 degree of target temp: Higher speed fans
|
BEDFANSFAST # If within 1 degree of target temp: Higher speed fans
|
||||||
{% else %}
|
{% else %}
|
||||||
|
|||||||
@@ -40,14 +40,12 @@ gcode:
|
|||||||
SKEW_PROFILE LOAD=Califlower
|
SKEW_PROFILE LOAD=Califlower
|
||||||
M106 S0
|
M106 S0
|
||||||
|
|
||||||
|
# Bed fans only help to heat a closed chamber: off for this print without
|
||||||
|
# one (heating/bed_fans.cfg). Set before the bed target, which reads it.
|
||||||
|
SET_GCODE_VARIABLE MACRO=_BEDFANVARS VARIABLE=print_fans_off VALUE={target_chamber <= 30}
|
||||||
|
|
||||||
# Bed first, so it heats during the rest of the warmup
|
# Bed first, so it heats during the rest of the warmup
|
||||||
{% if target_bed < 60 %}
|
SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={target_bed}
|
||||||
RESPOND MSG="Using PID for <60°C bed"
|
|
||||||
SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={target_bed} PID_KP=33.606 PID_KI=0.694 PID_KD=407.058
|
|
||||||
{% else %}
|
|
||||||
RESPOND MSG="Using PID for ≥60°C bed"
|
|
||||||
SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={target_bed} pid_Kp=46.843 pid_Ki=2.002 pid_Kd=274.034
|
|
||||||
{% endif %}
|
|
||||||
|
|
||||||
# Only to get the toolhead over the bed for the soak; the Z that counts
|
# Only to get the toolhead over the bed for the soak; the Z that counts
|
||||||
# is the contact calibration in PRINT_START on the soaked bed
|
# is the contact calibration in PRINT_START on the soaked bed
|
||||||
@@ -347,6 +345,7 @@ description: Heaters (incl. chamber heater) and part fan off, flow back to 100%,
|
|||||||
gcode:
|
gcode:
|
||||||
_GUARD_OFF ; a print start that failed while it was armed
|
_GUARD_OFF ; a print start that failed while it was armed
|
||||||
_BED_CHECK_RESET ; cancelled while the bed check had it paused
|
_BED_CHECK_RESET ; cancelled while the bed check had it paused
|
||||||
|
SET_GCODE_VARIABLE MACRO=_BEDFANVARS VARIABLE=print_fans_off VALUE=False
|
||||||
TURN_OFF_HEATERS
|
TURN_OFF_HEATERS
|
||||||
iHEATER_OFF ; stops the chamber heater control loop too
|
iHEATER_OFF ; stops the chamber heater control loop too
|
||||||
M107
|
M107
|
||||||
|
|||||||
Reference in new issue
Block a user