Bed soak on bed_side with a minimum time (measured)
Beacon meshes every 3 min on 2026-11-02 showed the 10 mm plate settles ~33 min after the bed reaches 100C with the chamber at 50C, and ~11 min at 60C with the chamber open. The old soak ended far earlier (bed_core within 5C, or the chamber reaching its target). HEAT_SOAK gets MIN_TIME=<minutes> (default 0); PRINT_WARMUP soaks on bed_side with RATE 0.05 over 120 s, SOAK_TEMP 70% of the bed target, MIN_TIME 35 (chamber) / 12 (no chamber), and skips the soak without a bed target. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
f25f348d0b
commit
13e49e43c7
2 files changed
+31
-9
No files matched your search
@@ -68,14 +68,28 @@ gcode:
|
||||
{% endif %}
|
||||
|
||||
{% if target_chamber > 30 %}
|
||||
RESPOND MSG="waiting for chamber temperature"
|
||||
RESPOND MSG="soaking the bed (chamber heating)"
|
||||
M141 S{target_chamber}
|
||||
M106 S255
|
||||
# Unreachable SOAK_TEMP + CANCEL='_NOTHING': soaks until the TIMEOUT, then continues the print
|
||||
HEAT_SOAK HEATER='heater_bed' TARGET={target_bed} SOAKER='temperature_sensor chamber' SOAK_TEMP={target_chamber} TIMEOUT=60 CANCEL='_NOTHING'
|
||||
{% else %}
|
||||
RESPOND MSG="waiting for bed core temperature"
|
||||
HEAT_SOAK HEATER='heater_bed' TARGET={target_bed} SOAKER='temperature_sensor bed_core' SOAK_TEMP={target_bed - 5} TIMEOUT=30 CANCEL='_NOTHING'
|
||||
RESPOND MSG="soaking the bed"
|
||||
{% endif %}
|
||||
# Soak until the 10 mm plate has its final shape. Measured 2026-11-02
|
||||
# (Beacon mesh every 3 min, tools/soak_run.py in the 3d printer folder):
|
||||
# bed 100C + chamber 50C settles ~33 min after the bed reaches target,
|
||||
# bed 60C with the chamber open ~11 min. bed_core reaches target long
|
||||
# before that, and swings with the PID cycle; bed_side (back edge) rises
|
||||
# until the plate is settled. MIN_TIME covers the measured time, RATE
|
||||
# makes a slower day (cold room) wait longer, SOAK_TEMP (70% of the bed
|
||||
# target) only keeps it from ending while the bed still heats.
|
||||
# CANCEL='_NOTHING': after TIMEOUT the print continues. No soak without
|
||||
# a bed target (nothing to soak, MIN_TIME would only wait).
|
||||
{% set soak_floor = (target_bed * 0.7) | round(1) %}
|
||||
{% if target_bed <= 0 %}
|
||||
{% elif target_chamber > 30 %}
|
||||
HEAT_SOAK HEATER='heater_bed' TARGET={target_bed} SOAKER='temperature_sensor bed_side' SOAK_TEMP={soak_floor} RATE=0.05 RATE_SMOOTH=120 MIN_TIME=35 TIMEOUT=60 CANCEL='_NOTHING'
|
||||
{% else %}
|
||||
HEAT_SOAK HEATER='heater_bed' TARGET={target_bed} SOAKER='temperature_sensor bed_side' SOAK_TEMP={soak_floor} RATE=0.05 RATE_SMOOTH=120 MIN_TIME=12 TIMEOUT=30 CANCEL='_NOTHING'
|
||||
{% endif %}
|
||||
|
||||
# With the chamber heated, filament in the toolhead path softens: a PLA lane
|
||||
|
||||
Reference in new issue
Block a user