| `messages.cfg` | `_ERROR`, `_WARN`: errors and warnings shown in the console and on the display (M117, the status line in Mainsail and KlipperScreen); PAUSE shows AFC's error, RESUME, CANCEL_PRINT and PRINT_WARMUP clear the display | — |
| `print_start_end.cfg` | `PRINT_WARMUP`, `PRINT_START`, `PRINT_END`; `_FIRST_LAYER_FAULT_DETECTION`: AFC buffer fault detection less sensitive during the first layer (needs one line in the slicer's layer change G-code, see the macro) | Beacon, AFC, Blobifier, `HEAT_SOAK`, iHeater, bd_pressure PA macros (bdwidth is no longer enabled while printing) |
| `pause_resume.cfg` | `PAUSE`, `RESUME`, `CANCEL_PRINT`, `M600` (RESUME also handles a running `HEAT_SOAK`, and after a PAUSE purges 40 mm with `BLOBIFIER_CHECKED` first: a failed check keeps the print paused, `RESUME PURGE=0` skips the purge; CANCEL_PRINT runs the same cleanup as `PRINT_END`) | `heating/heat_soak.cfg`, `leds/`, `blobifier/`, `afc/purge_check.cfg` |
| `homing.cfg` | `HOME`: X/Y, then Z always with Beacon contact (also when already homed); `_Z_CHECK`: stops the print when Klipper's Z and the Beacon reading differ (run in `PRINT_START` after the soak) | Beacon |
| `nozzle_guard.cfg` | `[bdp_guard]`, `_GUARD_ON PHASE=<name>`, `_GUARD_OFF`: bd_pressure watches the nozzle force during print-start moves where nothing should touch it (QGL, Z homing, mesh); `mode: stop` shuts Klipper down on a touch (the brush runs log-only), `mode: log` only reports the peak per phase | `extras/bdp_guard.py` + bd_pressure load-check firmware |
| `bed_fans.cfg` | Bed fans through `SET_HEATER_TEMPERATURE`/`M190`/`M140`/`TURN_OFF_HEATERS` overrides; off during a print without a heated chamber (`PRINT_WARMUP CHAMBER=` 30 or less), on during the cooldown after any print | `[fan_generic BedFans]` |
| `purge_check.cfg` | `BLOBIFIER_CHECKED`: checks every AFC purge with bd_pressure (and optionally bdwidth motion); a bd_pressure that does not answer fails the check, `PURGE_CHECK_IGNORE_SENSOR` lets the current print finish without it; when the previous filament (saved `nozzle_last_temp`) needs more than 10°C above the new one, the purge runs at the previous filament's temperature and the nozzle cools back afterwards, so its leftover melts out | Blobifier, AFC, `extras/bdpressure_check.py` + bd_pressure load-check firmware, `extras/bdwidth_status.py` |
| `flex_lanes.cfg` | Lanes holding TPU/TPE (material from Spoolman) get slower long moves (50 mm/s, AFC's minimum) through the tube; back to the configured speed when the lane holds something else. Polls every 5 s, reapplies after a restart. The last stretch into the extruder (`tool_load_speed`) stays as configured | AFC |
| `bd_pressure.cfg` | `[bdpressure bd_pa]` (I2C on the Nitehawk) and the vendor macros `PA_CALIBRATE`, `PA_E`, `PA_RESET`, `PA_STATE`; `PA_CALIBRATE` no longer sets Z back to a value read before the test (wrong after a Z hop in `G28 XY`) | `bdpressure.py` from the bd_pressure repo |
| `bd_pa_spoolman.cfg` + `bd_pa_*.sh` | `LANE_CALIBRATE_PA`, `PA_CALIBRATE_ALL_LANES`, `LANE_RECAL_PA`, `SET_SPOOL_ID`, `PA_STATUS`: pressure advance per lane/spool, cached locally and in Spoolman; before a calibration the lane's spool is assigned again so a temperature just changed in Spoolman is used; flexible materials (TPU/TPE) calibrate at a lower flow (8 mm³/s) and over a wider PA range (0–0.196 in 0.004 steps instead of 0–0.098); a calibration with no result, a pause during the test or too few/stuck sensor readings is rejected and not saved | bd_pressure, AFC, Spoolman, `gcode_shell_command` |
| `stealthburner_leds.cfg` | Stealthburner logo status (`_STATUS STATE=...`: heating and print progress as a filling logo, paused, error flash from `_ERROR`, part ready once the bed is cool, dim when idle and nobody is near) and the nozzle light | `led_effect`, `neopixel:bt_logo` and `rainbow_turtle` from AFC |
| `motion_sensor.cfg` | PIR motion sensor: case light and nozzle LEDs on while someone is near (timeout from the last motion), `CASELIGHT MODE=AUTO\|ON\|OFF`; runs outside the G-code queue, so the lights also react during heat waits and AFC loads | `extras/motion_lights.py`, sensor on a pin, `[output_pin caselight]`, `leds/stealthburner_leds.cfg` |
| `touch_compare.cfg` | `[bdp_touch]`, `TOUCH_COMPARE [N=10] [X] [Y] [TEMP=150]`: nozzle to 150C, `HOME`, then N pairs of a Beacon contact probe and a bd_pressure touch at one spot; reports mean, spread and range of each and of the difference | `extras/bdp_touch.py` + bd_pressure load-check firmware, Beacon |
| `twist_check.cfg` + `scripts/twist_check.py` | `TWIST_CALIBRATE`: axis twist calibration from Mainsail with windows that explain each step. Measure (25 min) says whether new `[axis_twist_compensation]` values are needed, Verify (17 min) checks them with bd_pressure. Progress on the status line, result in a window, HTML report with charts in `config/twist_data/`. Never changes `printer.cfg`. `TWIST_STOP` stops a run. | Beacon, `[axis_twist_compensation]`, `gcode_shell_command`, Mainsail prompts; Verify also `bdp_touch.py` |
| `bed_scan_check.cfg` | `BED_SCAN_CHECK [BUMP=0.03] [RANGE=0.30]`: levels, scans and warns about bumps, dips or too much height range, without heating or touching the bed. In `PRINT_START` a failed check pauses before the nozzle heats and moves the toolhead away: clean the plate and Resume, which runs `PRINT_START` again from QGL with a new scan and check. `BED_CHECK_IGNORE`, then Resume: the next failed check only warns | `extras/mesh_check.py`, Beacon, AFC |
| `xy_drift.py` | `AFC_XY_SAFETY_CHECK`: measures lost XY steps from the stepper step counts at the endstop triggers (CoreXY). The toolhead position after homing cannot show lost steps. |
| `bdwidth_status.py` | exposes bdwidth's motion counter and width to macros (`present: False` with neutral values when no bdwidth is configured, so the macros also work without it), and keeps a USB dropout of bdwidth (port: usb) from shutting down Klipper: the read is retried every 10 s and the port reopened |
| `bdpressure_check.py` | bd_pressure load check (`BDP_CHECK_START/STOP/QUERY`). Needs the load-check firmware from the bd_pressure `load-check-extension` branch; on stock firmware it reports "not available" and does nothing. Also reports how many readings the last `PA_CALIBRATE` got (`pa_points`, `pa_distinct`), used to reject runs with a silent or stuck sensor. |
| `bdp_guard.py` | nozzle collision guard: while armed (`BDP_GUARD_ARM/DISARM/QUERY`) reads the bd_pressure force every 20 ms over I2C and, in stop mode, shuts Klipper down when it stays above the threshold. Reports reads, peak and errors per phase in the console and klippy.log. When it arms and finds the sensor still in PA mode (an emergency stop during `PA_CALIBRATE`; `FIRMWARE_RESTART` does not reset the sensor), it switches it to probe mode and takes a new zero first. Puts a lock on the sensor's I2C connection that `bdpressure.py` and `bdpressure_check.py` also go through (Klipper allows one I2C request at a time per device). Needs the load-check firmware. |
| `bdp_touch.py` | `BDP_TOUCH`: lowers the nozzle in one slow continuous move (drip mode, like a homing move) while reading the bd_pressure force as fast as I2C allows (its endstop output is not wired), stops at a force limit (default 60) or 0.5 mm below the start, then lifts back; it must be one quick press, because the sensor re-zeros itself while the force looks steady; reports the height where the force reaches the threshold and the zero-force height from a line fit, and logs the whole curve to klippy.log. `_TOUCH_COMPARE`: alternates that with Beacon's contact probe. Refuses while the bdp_guard is armed or the sensor is in PA mode. Needs the load-check firmware. |
| `mesh_check.py` | `BED_MESH_CHECK`: fits a smooth surface to the loaded mesh and reports the height range and every area further from it than the limit, with its position. Only reads the mesh. Needs numpy (Beacon needs it too). |
| `blobifier/` | [Turtleblobifier](https://github.com/ImSundee/Turtleblobifier) (AFC version of [Dendrowen/Blobifier](https://github.com/Dendrowen/Blobifier)) |
| `leds/stealthburner_leds.cfg` | [tanaes/whopping_Voron_mods](https://github.com/tanaes/whopping_Voron_mods) (Rainbow Barf logo LEDs) |
| `heating/bed_fans.cfg` | Ellis' bed fan macros ([ellis3dp.com](https://ellis3dp.com/Print-Tuning-Guide/)) |
| `heating/heat_soak.cfg` | community `HEAT_SOAK` macro |