esphome-wake-up-light-ii/components/uart/uart_component_esp_idf.cpp

#ifdef USE_ESP32

#include "uart_component_esp_idf.h"
#include <cinttypes>
#include "esphome/core/defines.h"
#include "esphome/core/helpers.h"
#include "esphome/core/log.h"
#include "esphome/core/gpio.h"
#include "driver/gpio.h"
#include "hal/uart_ll.h"
#include "esp_private/gpio.h"
#include "soc/gpio_num.h"
#include "soc/soc_caps.h"
#include "soc/uart_pins.h"

#ifdef USE_UART_WAKE_LOOP_ON_RX
#include "esphome/core/application.h"
#endif

#ifdef USE_LOGGER
#include "esphome/components/logger/logger.h"
#endif

namespace esphome::uart {

static const char *const TAG = "uart";

/// Check if a pin number matches one of the default UART0 GPIO pins.
/// These pins may have residual IOMUX state from the ROM bootloader that
/// must be cleared before UART reconfiguration.
///
/// ESP-IDF's uart_set_pin() has an asymmetry: when routing TX via GPIO matrix,
/// it calls gpio_func_sel(PIN_FUNC_GPIO) to clear IOMUX, but for RX it only
/// calls gpio_input_enable() which does NOT clear the IOMUX function select.
/// If a default UART0 TX pin (configured as TX via IOMUX during boot) is later
/// reassigned as RX via GPIO matrix, the old IOMUX TX function remains active,
/// causing TX data to loop back into RX on the same pin.
static constexpr bool is_default_uart0_pin(int8_t pin_num) {
  return pin_num == U0TXD_GPIO_NUM || pin_num == U0RXD_GPIO_NUM;
}

// clock_source_ is stored in a byte; every uart_sclk_t value is a soc_module_clk_t below SOC_MOD_CLK_INVALID
static_assert(SOC_MOD_CLK_INVALID <= UINT8_MAX, "uart_sclk_t no longer fits in uint8_t clock_source_");

static const LogString *clock_source_to_str(uart_sclk_t clock_source) {
  switch (clock_source) {
#if SOC_UART_SUPPORT_APB_CLK
    case UART_SCLK_APB:
      return LOG_STR("APB");
#endif
#if SOC_UART_SUPPORT_XTAL_CLK
    case UART_SCLK_XTAL:
      return LOG_STR("XTAL");
#endif
#if SOC_UART_SUPPORT_RTC_CLK
    case UART_SCLK_RTC:
      return LOG_STR("RTC");
#endif
#if SOC_UART_SUPPORT_REF_TICK
    case UART_SCLK_REF_TICK:
      return LOG_STR("REF_TICK");
#endif
    default:
      return clock_source == UART_SCLK_DEFAULT ? LOG_STR("DEFAULT") : LOG_STR("UNKNOWN");
  }
}

uart_config_t IDFUARTComponent::get_config_() {
  uart_parity_t parity = UART_PARITY_DISABLE;
  if (this->parity_ == UART_CONFIG_PARITY_EVEN) {
    parity = UART_PARITY_EVEN;
  } else if (this->parity_ == UART_CONFIG_PARITY_ODD) {
    parity = UART_PARITY_ODD;
  }

  uart_word_length_t data_bits;
  switch (this->data_bits_) {
    case 5:
      data_bits = UART_DATA_5_BITS;
      break;
    case 6:
      data_bits = UART_DATA_6_BITS;
      break;
    case 7:
      data_bits = UART_DATA_7_BITS;
      break;
    case 8:
      data_bits = UART_DATA_8_BITS;
      break;
    default:
      data_bits = UART_DATA_BITS_MAX;
      break;
  }

  uart_config_t uart_config{};
  uart_config.baud_rate = this->baud_rate_;
  uart_config.data_bits = data_bits;
  uart_config.parity = parity;
  uart_config.stop_bits = this->stop_bits_ == 1 ? UART_STOP_BITS_1 : UART_STOP_BITS_2;
  uart_config.flow_ctrl = UART_HW_FLOWCTRL_DISABLE;
  uart_config.source_clk = static_cast<uart_sclk_t>(this->clock_source_);
  uart_config.rx_flow_ctrl_thresh = 122;

  return uart_config;
}

void IDFUARTComponent::setup() {
  static uint8_t next_uart_num = 0;

#ifdef USE_LOGGER
  bool logger_uses_hardware_uart = true;

#ifdef USE_LOGGER_USB_CDC
  if (logger::global_logger->get_uart() == logger::UART_SELECTION_USB_CDC) {
    // this is not a hardware UART, ignore it
    logger_uses_hardware_uart = false;
  }
#endif  // USE_LOGGER_USB_CDC

#ifdef USE_LOGGER_USB_SERIAL_JTAG
  if (logger::global_logger->get_uart() == logger::UART_SELECTION_USB_SERIAL_JTAG) {
    // this is not a hardware UART, ignore it
    logger_uses_hardware_uart = false;
  }
#endif  // USE_LOGGER_USB_SERIAL_JTAG

  if (logger_uses_hardware_uart && logger::global_logger->get_baud_rate() > 0 &&
      logger::global_logger->get_uart_num() == next_uart_num) {
    next_uart_num++;
  }
#endif  // USE_LOGGER

  if (next_uart_num >= SOC_UART_NUM) {
    ESP_LOGW(TAG, "Maximum number of UART components created already");
    this->mark_failed();
    return;
  }
  this->uart_num_ = static_cast<uart_port_t>(next_uart_num++);

#if (SOC_UART_LP_NUM >= 1)
  size_t fifo_len = ((this->uart_num_ < SOC_UART_HP_NUM) ? SOC_UART_FIFO_LEN : SOC_LP_UART_FIFO_LEN);
#else
  size_t fifo_len = SOC_UART_FIFO_LEN;
#endif
  if (this->rx_buffer_size_ <= fifo_len) {
    ESP_LOGW(TAG, "rx_buffer_size is too small, must be greater than %zu", fifo_len);
    this->rx_buffer_size_ = fifo_len * 2;
  }

  this->load_settings(false);
}

void IDFUARTComponent::load_settings(bool dump_config) {
  esp_err_t err;

  if (uart_is_driver_installed(this->uart_num_)) {
    err = uart_driver_delete(this->uart_num_);
    if (err != ESP_OK) {
      ESP_LOGW(TAG, "uart_driver_delete failed: %s", esp_err_to_name(err));
      this->mark_failed();
      return;
    }
  }
  err = uart_driver_install(this->uart_num_,        // UART number
                            this->rx_buffer_size_,  // RX ring buffer size
                            this->tx_buffer_size_,  // TX ring buffer size; 0 makes uart_write_bytes() block until
                                                    // the FIFO has taken everything
                            0,                      // event queue size/depth
                            nullptr,                // event queue
                            0                       // Flags used to allocate the interrupt
  );
  if (err != ESP_OK) {
    ESP_LOGW(TAG, "uart_driver_install failed: %s", esp_err_to_name(err));
    this->mark_failed();
    return;
  }

  // uart_param_config must be called after uart_driver_install and before any
  // other uart_set_*() calls. The driver installation resets the UART peripheral
  // registers to their default state, overwriting any previously configured baud
  // rate or framing settings. Calling uart_param_config here ensures the requested
  // settings are applied after the reset and before pin routing, inversion, and
  // threshold configuration.
  uart_config_t uart_config = this->get_config_();
  err = uart_param_config(this->uart_num_, &uart_config);
  if (err != ESP_OK) {
    ESP_LOGW(TAG, "uart_param_config failed: %s", esp_err_to_name(err));
    this->mark_failed();
    return;
  }
  this->last_good_framing_ = this->framing_();

  int8_t tx = this->tx_pin_ != nullptr ? this->tx_pin_->get_pin() : -1;
  int8_t rx = this->rx_pin_ != nullptr ? this->rx_pin_->get_pin() : -1;
  int8_t flow_control = this->flow_control_pin_ != nullptr ? this->flow_control_pin_->get_pin() : -1;

  // Clear residual IOMUX function on UART0 default pins left by the ROM bootloader.
  // See is_default_uart0_pin() comment for details on the ESP-IDF uart_set_pin() bug.
  if (is_default_uart0_pin(tx)) {
    gpio_func_sel(static_cast<gpio_num_t>(tx), PIN_FUNC_GPIO);
  }
  if (is_default_uart0_pin(rx)) {
    gpio_func_sel(static_cast<gpio_num_t>(rx), PIN_FUNC_GPIO);
  }

  auto setup_pin_if_needed = [](InternalGPIOPin *pin) {
    if (!pin) {
      return;
    }
    const auto mask = gpio::Flags::FLAG_OPEN_DRAIN | gpio::Flags::FLAG_PULLUP | gpio::Flags::FLAG_PULLDOWN;
    if ((pin->get_flags() & mask) != gpio::Flags::FLAG_NONE) {
      pin->setup();
    }
  };

  setup_pin_if_needed(this->rx_pin_);
  if (this->rx_pin_ != this->tx_pin_) {
    setup_pin_if_needed(this->tx_pin_);
  }

  // Must precede uart_set_pin() so an inverted TX line never shows the wrong idle
  // level; apply_line_settings_() repeats it later for the reset registers.
  err = uart_set_line_inverse(this->uart_num_, this->line_inversion_mask_());
  if (err != ESP_OK) {
    ESP_LOGW(TAG, "uart_set_line_inverse failed: %s", esp_err_to_name(err));
    this->mark_failed();
    return;
  }

  err = uart_set_pin(this->uart_num_, tx, rx, flow_control, UART_PIN_NO_CHANGE);
  if (err != ESP_OK) {
    ESP_LOGW(TAG, "uart_set_pin failed: %s", esp_err_to_name(err));
    this->mark_failed();
    return;
  }

  if (this->apply_line_settings_() != ESP_OK) {
    this->mark_failed();
    return;
  }

#ifdef USE_UART_WAKE_LOOP_ON_RX
  // Register ISR callback to wake the main loop when UART data arrives.
  // The callback runs in ISR context and uses vTaskNotifyGiveFromISR() to
  // wake the main loop task directly — no queue or FreeRTOS task needed.
  uart_set_select_notif_callback(this->uart_num_, IDFUARTComponent::uart_rx_isr_callback);
#endif  // USE_UART_WAKE_LOOP_ON_RX

  if (dump_config) {
    ESP_LOGCONFIG(TAG, "Reloaded UART %u", this->uart_num_);
    this->dump_config();
  }
}

uint32_t IDFUARTComponent::line_inversion_mask_() {
  uint32_t invert = 0;
  if (this->tx_pin_ != nullptr && this->tx_pin_->is_inverted()) {
    invert |= UART_SIGNAL_TXD_INV;
  }
  if (this->rx_pin_ != nullptr && this->rx_pin_->is_inverted()) {
    invert |= UART_SIGNAL_RXD_INV;
  }
  if (this->flow_control_pin_ != nullptr && this->flow_control_pin_->is_inverted()) {
    invert |= UART_SIGNAL_RTS_INV;
  }
  return invert;
}

esp_err_t IDFUARTComponent::apply_line_settings_() {
  // uart_param_config() resets these; call after every use of it.
  esp_err_t err = uart_set_line_inverse(this->uart_num_, this->line_inversion_mask_());
  if (err != ESP_OK) {
    ESP_LOGW(TAG, "uart_set_line_inverse failed: %s", esp_err_to_name(err));
    return err;
  }

  err = uart_set_rx_full_threshold(this->uart_num_, this->rx_full_threshold_);
  if (err != ESP_OK) {
    ESP_LOGW(TAG, "uart_set_rx_full_threshold failed: %s", esp_err_to_name(err));
    return err;
  }

  err = uart_set_rx_timeout(this->uart_num_, this->rx_timeout_);
  if (err != ESP_OK) {
    ESP_LOGW(TAG, "uart_set_rx_timeout failed: %s", esp_err_to_name(err));
    return err;
  }

  // Per ESP-IDF docs, uart_set_mode() must be called only after uart_driver_install().
  auto mode = this->flow_control_pin_ != nullptr ? UART_MODE_RS485_HALF_DUPLEX : UART_MODE_UART;
  err = uart_set_mode(this->uart_num_, mode);
  if (err != ESP_OK) {
    ESP_LOGW(TAG, "uart_set_mode failed: %s", esp_err_to_name(err));
    return err;
  }

  return ESP_OK;
}

void IDFUARTComponent::set_framing_(const Framing &framing) {
  this->baud_rate_ = framing.baud_rate;
  this->data_bits_ = framing.data_bits;
  this->stop_bits_ = framing.stop_bits;
  this->parity_ = framing.parity;
  this->rx_full_threshold_ = framing.rx_full_threshold;
}

esp_err_t IDFUARTComponent::apply_settings_live() {
  if (this->is_failed()) {
    return ESP_ERR_INVALID_STATE;
  }
  // No driver yet: nothing to reconfigure in place.
  if (!uart_is_driver_installed(this->uart_num_)) {
    this->load_settings(false);
    return this->is_failed() ? ESP_FAIL : ESP_OK;
  }
  // Keeps the driver ring buffers; flushes both hardware FIFOs (in-flight bytes lost).
  uart_config_t uart_config = this->get_config_();
  esp_err_t err = uart_param_config(this->uart_num_, &uart_config);
  if (err != ESP_OK) {
    // Failure leaves the registers reset; put back the last accepted framing so the
    // getters still describe the hardware.
    if (this->last_good_framing_.baud_rate == 0) {
      ESP_LOGE(TAG, "uart_param_config (live) failed: %s; no previous framing to restore", esp_err_to_name(err));
      this->mark_failed();
      return err;
    }
    ESP_LOGW(TAG, "uart_param_config (live) failed: %s; restoring %" PRIu32 " baud", esp_err_to_name(err),
             this->last_good_framing_.baud_rate);
    this->set_framing_(this->last_good_framing_);
    uart_config = this->get_config_();
    esp_err_t restore_err = uart_param_config(this->uart_num_, &uart_config);
    if (restore_err != ESP_OK) {
      ESP_LOGE(TAG, "UART left unconfigured after failed live reconfigure: %s", esp_err_to_name(restore_err));
      this->mark_failed();
      return err;
    }
    // Previous framing is live again; report the refusal (line-setting errors log).
    this->apply_line_settings_();
    return err;
  }
  this->last_good_framing_ = this->framing_();
  // The new framing is live; a line-setting failure here only logs.
  this->apply_line_settings_();
  return ESP_OK;
}

void IDFUARTComponent::dump_config() {
  ESP_LOGCONFIG(TAG, "UART Bus %u:", this->uart_num_);
  LOG_PIN("  TX Pin: ", this->tx_pin_);
  LOG_PIN("  RX Pin: ", this->rx_pin_);
  LOG_PIN("  Flow Control Pin: ", this->flow_control_pin_);
  if (this->rx_pin_ != nullptr) {
    ESP_LOGCONFIG(TAG,
                  "  RX Buffer Size: %u\n"
                  "  RX Full Threshold: %u\n"
                  "  RX Timeout: %u",
                  this->rx_buffer_size_, this->rx_full_threshold_, this->rx_timeout_);
  }
  if (this->tx_buffer_size_ > 0) {
    ESP_LOGCONFIG(TAG, "  TX Buffer Size: %zu", this->tx_buffer_size_);
  }
  if (this->flush_timeout_ms_ > 0) {
    ESP_LOGCONFIG(TAG, "  Flush Timeout: %" PRIu32 " ms", this->flush_timeout_ms_);
  }
  ESP_LOGCONFIG(TAG,
                "  Baud Rate: %" PRIu32 " baud\n"
                "  Data Bits: %u\n"
                "  Parity: %s\n"
                "  Stop bits: %u\n"
                "  Clock Source: %s"
#ifdef USE_UART_WAKE_LOOP_ON_RX
                "\n  Wake on data RX: ENABLED"
#endif
                ,
                this->baud_rate_, this->data_bits_, LOG_STR_ARG(parity_to_str(this->parity_)), this->stop_bits_,
                LOG_STR_ARG(clock_source_to_str(static_cast<uart_sclk_t>(this->clock_source_))));
  this->check_logger_conflict();
}

void IDFUARTComponent::set_rx_full_threshold(size_t rx_full_threshold) {
  if (this->is_ready()) {
    esp_err_t err = uart_set_rx_full_threshold(this->uart_num_, rx_full_threshold);
    if (err != ESP_OK) {
      ESP_LOGW(TAG, "uart_set_rx_full_threshold failed: %s", esp_err_to_name(err));
      return;
    }
  }
  this->rx_full_threshold_ = rx_full_threshold;
}

void IDFUARTComponent::set_rx_timeout(size_t rx_timeout) {
  if (this->is_ready()) {
    esp_err_t err = uart_set_rx_timeout(this->uart_num_, rx_timeout);
    if (err != ESP_OK) {
      ESP_LOGW(TAG, "uart_set_rx_timeout failed: %s", esp_err_to_name(err));
      return;
    }
  }
  this->rx_timeout_ = rx_timeout;
}

size_t IDFUARTComponent::available_for_write() {
  if (this->uart_num_ == UART_NUM_MAX || !uart_is_driver_installed(this->uart_num_))
    return 0;
  if (this->tx_buffer_size_ == 0) {
    return uart_ll_get_txfifo_len(UART_LL_GET_HW(this->uart_num_));
  }
  // The driver's figure already deducts its ring item headers, so a write of this size fits
  size_t free = 0;
  uart_get_tx_buffer_free_size(this->uart_num_, &free);
  return free;
}

void IDFUARTComponent::write_array(const uint8_t *data, size_t len) {
  int32_t write_len = uart_write_bytes(this->uart_num_, data, len);
  if (write_len != (int32_t) len) {
    ESP_LOGW(TAG, "uart_write_bytes failed: %" PRId32 " != %zu", write_len, len);
    this->mark_failed();
  }
#ifdef USE_UART_DEBUGGER
  for (size_t i = 0; i < len; i++) {
    this->debug_callback_.call(UART_DIRECTION_TX, data[i]);
  }
#endif
}

bool IDFUARTComponent::peek_byte(uint8_t *data) {
  if (!this->check_read_timeout_())
    return false;
  if (this->has_peek_) {
    *data = this->peek_byte_;
  } else {
    int len = uart_read_bytes(this->uart_num_, data, 1, 20 / portTICK_PERIOD_MS);
    if (len == 0) {
      *data = 0;
    } else {
      this->has_peek_ = true;
      this->peek_byte_ = *data;
    }
  }
  return true;
}

bool IDFUARTComponent::read_array(uint8_t *data, size_t len) {
  if (len == 0) {
    return false;
  }
  size_t length_to_read = len;
  int32_t read_len = 0;
  if (!this->check_read_timeout_(len))
    return false;
  if (this->has_peek_) {
    length_to_read--;
    *data = this->peek_byte_;
    this->has_peek_ = false;
  }
  if (length_to_read > 0)
    read_len = uart_read_bytes(this->uart_num_, data + (len - length_to_read), length_to_read, 20 / portTICK_PERIOD_MS);
#ifdef USE_UART_DEBUGGER
  for (size_t i = 0; i < len; i++) {
    this->debug_callback_.call(UART_DIRECTION_RX, data[i]);
  }
#endif
  return read_len == (int32_t) length_to_read;
}

size_t IDFUARTComponent::available() {
  size_t available = 0;
  esp_err_t err;

  err = uart_get_buffered_data_len(this->uart_num_, &available);

  if (err != ESP_OK) {
    ESP_LOGW(TAG, "uart_get_buffered_data_len failed: %s", esp_err_to_name(err));
    this->mark_failed();
  }
  if (this->has_peek_) {
    available++;
  }
  return available;
}

UARTFlushResult IDFUARTComponent::flush() {
  ESP_LOGVV(TAG, "    Flushing");
  TickType_t ticks = this->flush_timeout_ms_ == 0 ? portMAX_DELAY : pdMS_TO_TICKS(this->flush_timeout_ms_);
  esp_err_t err = uart_wait_tx_done(this->uart_num_, ticks);
  if (err == ESP_OK)
    return UARTFlushResult::UART_FLUSH_RESULT_SUCCESS;
  if (err == ESP_ERR_TIMEOUT)
    return UARTFlushResult::UART_FLUSH_RESULT_TIMEOUT;
  return UARTFlushResult::UART_FLUSH_RESULT_FAILED;
}

void IDFUARTComponent::check_logger_conflict() {}

#ifdef USE_UART_WAKE_LOOP_ON_RX
// ISR callback invoked by the ESP-IDF UART driver when data arrives.
// Wakes the main loop directly via vTaskNotifyGiveFromISR() — no queue or task needed.
void IRAM_ATTR IDFUARTComponent::uart_rx_isr_callback(uart_port_t uart_num, uart_select_notif_t uart_select_notif,
                                                      BaseType_t *task_woken) {
  if (uart_select_notif == UART_SELECT_READ_NOTIF) {
    Application::wake_loop_isrsafe(task_woken);
  }
}
#endif  // USE_UART_WAKE_LOOP_ON_RX

void IDFUARTComponent::on_shutdown() {
  if (this->uart_num_ == UART_NUM_MAX || !uart_is_driver_installed(this->uart_num_))
    return;
  uart_wait_tx_done(this->uart_num_, pdMS_TO_TICKS(100));
  // Keep the peripheral quiet across a soft reset so ROM output does not reach the attached device (#15472)
  esp_err_t err = uart_driver_delete(this->uart_num_);
  if (err != ESP_OK) {
    ESP_LOGW(TAG, "uart_driver_delete failed: %s", esp_err_to_name(err));
  }
}

}  // namespace esphome::uart
#endif  // USE_ESP32