Update the patched UART component to ESPHome 2026.11.0
ESPHome 2026.11's tuya component calls uart.new_uart_component(), which the 2026.10.2 copy didn't have, so the build failed. Copy the UART component from 2026.11.0, reapply the PA13/PA14 patch, regenerate the patch file and point the refs at v1.0.6. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
bcc6b3a42b
commit
1457e25d98
39 files changed
+907
-304
No files matched your search
@@ -23,6 +23,14 @@ enum UARTParityOptions {
|
||||
UART_CONFIG_PARITY_SPACE,
|
||||
};
|
||||
|
||||
// A runtime setting like CRTSCTS and IXON/IXOFF in termios. A backend without the lines
|
||||
// keeps the value and ignores it, as a Linux driver does.
|
||||
enum UARTFlowControl : uint8_t {
|
||||
UART_FLOW_CONTROL_NONE,
|
||||
UART_FLOW_CONTROL_RTS_CTS,
|
||||
UART_FLOW_CONTROL_XON_XOFF,
|
||||
};
|
||||
|
||||
#ifdef USE_UART_DEBUGGER
|
||||
enum UARTDirection {
|
||||
UART_DIRECTION_RX,
|
||||
@@ -65,6 +73,13 @@ class UARTComponent {
|
||||
// @param len Length of the array.
|
||||
virtual void write_array(const uint8_t *data, size_t len) = 0;
|
||||
|
||||
// Writes bytes that may live in PROGMEM; ESP8266 cannot read flash bytewise, so it copies chunks.
|
||||
#ifdef USE_ESP8266
|
||||
void write_array_progmem(const uint8_t *data, size_t len);
|
||||
#else
|
||||
void write_array_progmem(const uint8_t *data, size_t len) { this->write_array(data, len); }
|
||||
#endif
|
||||
|
||||
// Reads a single byte from the UART bus.
|
||||
// @param data Pointer to the byte where the read data will be stored.
|
||||
// @return True if a byte was successfully read, false otherwise.
|
||||
@@ -89,6 +104,10 @@ class UARTComponent {
|
||||
// Platforms that cannot tell return SIZE_MAX: write_array() takes everything and may block.
|
||||
virtual size_t available_for_write() { return SIZE_MAX; }
|
||||
|
||||
// Bytes a write can take now. Where available_for_write() cannot tell (SIZE_MAX), paces to the line time since
|
||||
// last_write_ms, a loop start time: at most one loop interval and 4 s, at least one byte.
|
||||
size_t paced_write_room(uint32_t last_write_ms);
|
||||
|
||||
// Pure virtual method to block until all bytes have been written to the UART bus.
|
||||
// @return UARTFlushResult indicating whether the flush was confirmed, timed out, failed, or assumed successful.
|
||||
virtual UARTFlushResult flush() = 0;
|
||||
@@ -174,6 +193,15 @@ class UARTComponent {
|
||||
// @return Baud rate in bits per second.
|
||||
uint32_t get_baud_rate() const { return baud_rate_; }
|
||||
|
||||
// Set the line handshaking (RTS/CTS or XON/XOFF) used in UART communication. Unrelated to
|
||||
// flow_control_pin, the RS485 driver enable; backends without handshaking ignore it.
|
||||
// @param flow_control Flow control option.
|
||||
void set_flow_control(UARTFlowControl flow_control) { this->flow_control_ = flow_control; }
|
||||
|
||||
// Get the flow control used in UART communication.
|
||||
// @return Flow control option.
|
||||
UARTFlowControl get_flow_control() const { return this->flow_control_; }
|
||||
|
||||
#if defined(USE_ESP8266) || defined(USE_ESP32)
|
||||
/**
|
||||
* Load the UART settings.
|
||||
@@ -220,6 +248,7 @@ class UARTComponent {
|
||||
uint32_t baud_rate_{0};
|
||||
uint8_t stop_bits_{0};
|
||||
uint8_t data_bits_{0};
|
||||
UARTFlowControl flow_control_{UART_FLOW_CONTROL_NONE};
|
||||
UARTParityOptions parity_{UART_CONFIG_PARITY_NONE}; // Must match the parity check in __init__.py
|
||||
#ifdef USE_UART_DEBUGGER
|
||||
CallbackManager<void(UARTDirection, uint8_t)> debug_callback_{};
|
||||
|
||||
Reference in new issue
Block a user