ESPHome firmware for a Moes Wake Up Light II (Tuya PID `ya39qahrcdhvxowz`), running fully local. This repo is public, so never commit secrets, Wi-Fi details or device keys.
## Layout
-`wake-up-light-ii.yaml`: main config.
-`alarm_block.yaml`: controls for one alarm, included 4 times.
-`alarm_day.yaml`: one weekday switch, included 7 times per alarm.
-`components/uart`: ESPHome 2026.10.2's UART component with `patches/wbr3-pa13-pa14-uart.patch` applied. Recheck it when ESPHome updates.
-`server-example.yaml`: the short YAML that goes on an ESPHome server.
-`secrets.yaml`: local only, ignored by git. Needs `wifi_ssid`, `wifi_password`, `ap_password`, `api_encryption_key`.
## Releasing
1. Set the `ref` in `wake-up-light-ii.yaml`'s `external_components` to the new tag, then commit and tag that commit.
2. Push the branch and the tag. On the owner's PC the first push can fail authentication, and a second try works.
3. Update `ref` in the server's YAML, then press Install. OTA works, and the lamp restarts by itself.
Build from a short folder path: Windows path limits break the libsodium build otherwise.
## Hardware
- WBR3 module (RTL8720CF, 2 MiB flash), talking TuyaMCU at 9600 8N1 on PA13 (RX) and PA14 (TX).
- Knock sensor: a switch between 3.3V and PA18, using the internal pull-down.
- UART flashing needs the module desoldered, because PA00 is on the underside. Adapter TX to PA15, RX to PA16, plus GND and a solid 3.3V. Hold PA00 at 3.3V, then tap CEN to GND. PA13 must not be pulled low.
- Serial reads with `ltchiptool` run at about 3 KB/s, so a full 2 MiB backup takes about 16 minutes.
- If the serial port says "access denied", another app has it. On the owner's PC that was SignalRGB.
## Data model
From Tuya's definition for a sibling product (tuya-local issue #3821). See the README's corrections section for the byte layouts of DP127, DP128 and DP107.
- A raw UART capture of a ring, radio, scan and sunset showed only heartbeats and normal datapoint frames. No other message types, and no datapoints beyond these 22.
- There is no "ringing" datapoint. A ring starts with DP101, 105, 121, 129 and 130 all OFF in one burst (3 of 3 rings). Arming an alarm inside its sunrise window sends only DP101, 121 and 129.
- The stop and volume buttons send nothing to the chip, and neither did the window where a ring should have stopped by itself. So a hand-stopped alarm can't be detected without extra hardware.
- A knock during a ring snoozes it. DP130 then stays ON. Outside an alarm it returns to OFF at once.
- DP127 writes are ignored while an alarm is snoozed.
- A mode without light sets brightness to 0, and a light mode with brightness 0 falls back to no light, so the firmware sets a level when choosing a light mode.
- Alarm radio stations were reset to 1 while no stations were saved.
- Keep `default_transition_length` at 0. A transition sends about 50 MCU writes a second.
- LibreTiny before v1.14.0 can hang after a software restart or OTA until powered off for about 30 seconds (LibreTiny issue #396). The config pins v1.14.0. Drop the pin once ESPHome defaults to it or newer.
- "Last Restart Reason" reports Power-On even after software restarts.
## Status
Verified:
- Alarm and sunset settings are echoed by the MCU.
- Wednesday-only rang on a Wednesday, which fits bit 0 = Monday. A Tuesday-only silent test was skipped.
- Sunset starts and stops. Its sound was heard, and a glow was seen but not clearly caused by it.
- A manual scan found 2 stations, while a scan started from the firmware found 0.
