# Example ESPHome config for a Samsung 2x20 serial VFD display.
#
# Copy this file into your ESPHome config folder (and add the keys below to
# your secrets.yaml), or use it as a reference for your own device config.
#
# Wiring (3-pin connector on the display, 9600 8N1):
#   pin 1 VCC <-  5-24V supply, up to 1.2A at 5V (not the ESP32 regulator)
#   pin 2 RXD <-  MAX3232 T1OUT  <-  T1IN  <-  ESP32 GPIO17 (TX)
#   pin 3 GND <-> supply GND, MAX3232 GND and ESP32 GND
#
# RXD is an RS-232 input. Without a MAX3232, wire GPIO17 straight to RXD and
# set `inverted: true` under uart.

esphome:
  name: samsung-vfd
  friendly_name: Samsung VFD
  on_boot:
    priority: -100
    then:
      - samsung_vfd.clear:
          id: vfd
      - samsung_vfd.print:
          id: vfd
          text: "Hello World! ~"  # "~" is the heart defined below
          centered: true
      - delay: 3s
      # Bring back the last text Home Assistant set for the top line.
      - samsung_vfd.print:
          id: vfd
          line: 0
          text: !lambda "return id(vfd_line1).state;"

external_components:
  - source:
      type: git
      url: https://mangavalk.com/mangavalk/esphome-samsung-vfd
      ref: main
    components: [samsung_vfd]
    refresh: 1d
  # While developing the component, use the checkout instead:
  # - source:
  #     type: local
  #     path: ../components

esp32:
  board: esp32dev
  framework:
    type: arduino

logger:
  level: INFO

api:
  encryption:
    key: !secret api_key

ota:
  - platform: esphome
    password: !secret ota_password

wifi:
  ssid: !secret wifi_ssid
  password: !secret wifi_password
  # Uncomment to pin a fixed address.
  # manual_ip:
  #   static_ip: 10.1.1.60
  #   gateway: 10.1.1.1
  #   subnet: 255.255.255.0
  ap:
    ssid: "Samsung VFD Fallback"
    password: !secret fallback_password

captive_portal:

# SNTP so samsung_vfd.printf can show the local time.
time:
  - platform: sntp
    id: sntp_time
    timezone: Europe/Amsterdam
    servers:
      - 0.pool.ntp.org
      - 1.pool.ntp.org

# Must match the display's jumpers; all open (factory default) = 9600, no parity.
uart:
  id: uart_vfd
  tx_pin:
    number: GPIO17
    inverted: false   # true when wired directly, without a MAX3232
  baud_rate: 9600
  parity: NONE
  # The display is output-only for us; no rx_pin needed.

samsung_vfd:
  id: vfd
  uart_id: uart_vfd
  cols: 20
  rows: 2
  brightness: 100%
  code_table: PC437           # glyphs for é, ü, °, ½, box drawing ... (match jumpers 6-8)
  international_charset: USA
  # Up to 4 custom glyphs, replacing a printable ASCII character you don't use.
  user_characters:
    - code: "~"
      pattern:
        - ".#.#."
        - "#####"
        - "#####"
        - "#####"
        - ".###."
        - "..#.."
        - "....."

# Bottom line shows the SNTP clock every second, except while a status banner is up.
interval:
  - interval: 1s
    then:
      - if:
          condition:
            not:
              script.is_running: show_status
          then:
            - samsung_vfd.printf:
                id: vfd
                time_id: sntp_time
                line: 1
                format: "%a %d %b  %H:%M:%S"

# Full-screen centred banner for a while, then back to line 1 + clock.
script:
  - id: show_status
    mode: restart
    parameters:
      msg: string
    then:
      - samsung_vfd.print:
          id: vfd
          text: !lambda "return msg;"
          centered: true
      - delay: 10s
      - samsung_vfd.print:
          id: vfd
          line: 0
          text: !lambda "return id(vfd_line1).state;"
      - samsung_vfd.printf:
          id: vfd
          time_id: sntp_time
          line: 1
          format: "%a %d %b  %H:%M:%S"

# Two Home Assistant text entities you can type into from HA.
text:
  - platform: template
    id: vfd_line1
    name: "VFD line 1"
    icon: mdi:text-box-outline
    mode: text
    max_length: 20
    optimistic: true
    restore_value: true
    initial_value: ""
    on_value:
      then:
        - if:
            condition:
              not:
                script.is_running: show_status
            then:
              - samsung_vfd.print:
                  id: vfd
                  line: 0
                  text: !lambda "return x;"

  - platform: template
    id: vfd_status
    name: "VFD status"
    icon: mdi:information-outline
    mode: text
    max_length: 40
    optimistic: true
    initial_value: ""
    on_value:
      then:
        - if:
            condition:
              lambda: "return !x.empty();"
            then:
              - script.execute:
                  id: show_status
                  msg: !lambda "return x;"

# Brightness (4 levels) and power from Home Assistant.
select:
  - platform: template
    name: "VFD brightness"
    icon: mdi:brightness-6
    optimistic: true
    restore_value: true
    options: ["40%", "60%", "80%", "100%"]
    initial_option: "100%"
    on_value:
      then:
        - samsung_vfd.set_brightness:
            id: vfd
            brightness: !lambda "return (i + 2) * 0.2f;"

switch:
  - platform: template
    name: "VFD display"
    icon: mdi:monitor
    optimistic: true
    restore_mode: RESTORE_DEFAULT_ON
    turn_on_action:
      - samsung_vfd.turn_on:
          id: vfd
    turn_off_action:
      - samsung_vfd.turn_off:
          id: vfd