Compare commits

..
10 Commits
Author SHA1 Message Date
mangavalkandClaude Opus 5.5 640ac243be Docs: WEMOS D1 R1 (ESP8266) instead of ESP32
The reference build now uses a D1 R1. The example config targets
esp8266/d1 and sends on GPIO2 (header pin D9, UART1 TX), which leaves
UART0 free for the USB logger. The README wiring and signal-level notes
are updated to match.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-02 18:19:24 +01:00
mangavalkandClaude Opus 5.5 4aaa1a4610 Case: two more body screws near the front
The base only screwed to the body at the back. New bosses in the side walls sit just behind the display, clear of the bezel's slide-in path; the base rim gets a gap around them and the feet part now has 6 feet.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-01 21:24:44 +01:00
mangavalkandClaude Opus 5.5 6a52f1af0b Case: 4.2 mm insert holes, M3x8 base screws with the feet
The 4.0 mm holes printed too tight for CNC Kitchen M3x5.7 inserts.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-01 18:01:28 +01:00
mangavalkandClaude Opus 5.5 b8e045d8d6 Case: 12 inserts, M3x6 for the display
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-01 16:35:55 +01:00
mangavalkandClaude Opus 5.5 bd773982f8 Case: add TPU feet held by the base screws
Each foot has a spigot that locates in the base's screw counterbore and a
pocket for the screw head; base screws become M3x10. Base unchanged.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-01 13:06:07 +01:00
mangavalkandClaude Opus 5.5 bf17b9c0ba Case README: keep measurement list together
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-01 13:04:01 +01:00
mangavalkandClaude Opus 5.5 02f8289852 Case: mount the display the right way up
The glass is 4.4 mm off-centre on the display PCB. Turning the display
180 degrees so the text reads correctly moved the glass partly behind the
window edge. New disp_rotated option (default on) moves the bezel bosses
to match. Only the bezel changes.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-01 13:03:53 +01:00
mangavalkandClaude Opus 5.5 17d0c1be3b Add 3D-printable desk case for the VFD and a WEMOS D1 R1
Parametric OpenSCAD design: 15 degree bezel holding the display on M3
heat-set inserts, slides into the body; base carries the board with the
DC jack and USB reachable through the back. Includes STLs, previews and
collision checks.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 19:32:43 +01:00
mangavalkandClaude Opus 5.5 49546ce3b3 Support every datasheet command and map text to the CG-ROM fonts
- Brightness, blink, screen on/off, annunciators, cursor control, display
  modes, user-defined characters, code table, international charset,
  peripheral select, self-test, raw writes and reinit
- UTF-8 text is encoded with the selected code table (tables generated
  from Python codecs by tools/gen_charmaps.py), falling back to
  accent-stripping
- Settings survive reinit and the self-test
- Example gains brightness select and display switch, and uses the git
  source on mangavalk.com

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 17:55:36 +01:00
mangavalkandClaude Opus 5.5 a4e5694a1d Add photos and datasheet; correct wiring and protocol docs
The 20L203 input is RS-232 (reference build uses a MAX3232), it runs on
5-24 V, and it boots in non-scrolling overwrite mode.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 17:44:07 +01:00
6 changed files with 4 additions and 28 deletions

No files matched your search

+4 -20
View File
@@ -82,26 +82,10 @@ through a MAX3232. The [desk case](case/README.md) is made for that board.
### Power
The display takes 4.5–26 V. Its supply current with all dots lit (datasheet
section 4.6):
| Supply | Typical | Maximum | Inrush at power-on (5 × max) |
|--------|---------|---------|------------------------------|
| 5 V | 0.8 A | 1.2 A | up to 6 A |
| 12 V | 0.35 A | 0.55 A | up to 2.75 A |
| 24 V | 0.2 A | 0.3 A | up to 1.5 A |
The inrush current sets the size of the supply, not the running current. A
12 V 1 A adapter is **not enough**: it current-limits at power-on and the
display browns out during start-up. A dev-board regulator can't supply this
either, so give the display its own supply and connect the grounds together:
- **12 V, 3 A or more** (recommended). The D1 R1 can share it through its
barrel jack, which accepts up to 12 V.
- **12 V, 2 A plus a bulk capacitor** of 2200 µF / 25 V or more across VCC and
GND at the display connector, so the capacitor supplies the inrush peak.
- **24 V, 2 A.** This has the lowest current, but don't feed it to the D1 R1's
barrel jack: power the board separately, e.g. over USB.
The display takes 5–24 V. At 5 V it draws about 0.8 A typical and 1.2 A
maximum, and the inrush current at power-on can be up to five times that. A
dev-board regulator can't supply this, so give the display its own supply,
for example 12 V at 1 A, and connect the grounds together.
### Signal levels
-8
View File
@@ -10,14 +10,6 @@ back wall.
<img src="section.png" alt="Cross-section: display on the bezel, board on the base" width="49%">
</p>
The printed build, assembled and with the body removed (D1 R1 with a
proto shield carrying the MAX3232):
<p>
<img src="build-front.jpg" alt="Printed case, assembled" width="49%">
<img src="build-inside.jpg" alt="Inside the case: display on the bezel, D1 R1 on the base" width="49%">
</p>
Outer size: about 208 × 112 × 86 mm (W × D × H). The parts need a print bed of
at least 210 × 115 mm.
Binary file not shown.

Before

Width:  |  Height:  |  Size: 3.3 MiB

Binary file not shown.

Before

Width:  |  Height:  |  Size: 2.5 MiB

BIN
View File
Binary file not shown.

Before

Width:  |  Height:  |  Size: 1.4 MiB

After

Width:  |  Height:  |  Size: 1.4 MiB

BIN
View File
Binary file not shown.

Before

Width:  |  Height:  |  Size: 3.1 MiB

After

Width:  |  Height:  |  Size: 3.1 MiB