Compare commits

...
2 Commits
Author SHA1 Message Date
mangavalkandClaude Opus 5.5 6a52f1af0b Case: 4.2 mm insert holes, M3x8 base screws with the feet
The 4.0 mm holes printed too tight for CNC Kitchen M3x5.7 inserts.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-01 18:01:28 +01:00
mangavalkandClaude Opus 5.5 b8e045d8d6 Case: 12 inserts, M3x6 for the display
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-01 16:35:55 +01:00
6 changed files with 10 additions and 9 deletions

No files matched your search

+7 -6
View File
@@ -27,15 +27,16 @@ works if the case stays out of the sun.
## Hardware
- 10 × M3 heat-set inserts (about 4.6 mm OD, 5.7 mm long; the holes are 4.0 mm
and 6 mm deep):
- 12 × M3 heat-set inserts, CNC Kitchen M3 × 5.7 (about 4.6 mm OD; the holes
are 4.2 mm and 6 mm deep, set by `insert_d` if your printer runs tighter or
looser):
- 4 in the bezel's display bosses
- 2 in the bezel's feet
- 2 in the body's rear corners
- 4 on the base's board standoffs
- 4 × M3×8 to bolt the display to the bezel
- 4 × M3×6 to bolt the display to the bezel
- 4 × M3×6 to hold the D1 board on its standoffs
- 4 × M3×8 to hold the base on, from below; **M3×10** with the TPU feet
- 4 × M3×8 to hold the base on, from below (also with the TPU feet)
## Assembly
@@ -48,8 +49,8 @@ works if the case stays out of the sun.
the anchor on the base.
6. Put the body on the base and screw it together from below. The base holds
the bezel in place. With the feet, put a foot on each screw first (the
spigot faces the base) and use M3×10. Tighten until the foot is snug; the
TPU only needs light compression.
spigot faces the base); M3×8 is still long enough. Tighten until the foot
is snug; the TPU only needs light compression.
## Measure before printing
BIN
View File
Binary file not shown.
Binary file not shown.
BIN
View File
Binary file not shown.
BIN
View File
Binary file not shown.
+3 -3
View File
@@ -8,7 +8,7 @@
// Assembly:
// 1. Melt M3 heat-set inserts into: 4 display bosses + 2 feet on the bezel,
// 2 rear corner bosses in the body, 4 board standoffs on the base.
// 2. Bolt the display to the bezel from behind (4x M3x8).
// 2. Bolt the display to the bezel from behind (4x M3x6).
// 3. Screw the D1 board onto the base (4x M3x6).
// 4. Slide the bezel (with display) up into the body's side grooves from below.
// 5. Wire up, put the body on the base and screw it together from below (4x M3x8).
@@ -55,14 +55,14 @@ win_r = 2;
win_chamfer = 1.5;
/* [Heat-set inserts, M3] */
insert_d = 4.0; // hole for the insert
insert_d = 4.2; // hole for the insert (CNC Kitchen M3x5.7; 4.0 printed too tight)
insert_depth = 6;
boss_d = 7; // display bosses (larger would touch the glass)
screw_d = 3.4; // M3 clearance
head_d = 6.2; // M3 head counterbore in the base
head_depth = 2;
/* [TPU feet, held by the base screws (use M3x10 instead of M3x8)] */
/* [TPU feet, held by the base screws (M3x8 still fits)] */
foot_d = 14; // fits inside the base outline at the rear corners
foot_h = 4.5; // below the base
foot_spigot_h = 1.8; // locates in the base's screw counterbore